RICHTEK RD0001-01 Wrenboard General USB-I2C GPIO PWM Tool Kit User Manual
- October 27, 2023
- RICHTEK
Table of Contents
RICHTEK RD0001-01 Wrenboard General USB-I2C GPIO PWM Tool Kit
Introduction
Nowadays, most of ICs contain digital interface in order to control
increasingly complex ICs easily. Richtek
Technology developed a bridge board to control the device with digital
interface. The bridge board, Wrenboard, provides I2C and GPIO, which can be
utilized as 1-wire/PWM. In addition, we also provide the PC-based software
(Richtek Bridgeboard Utilities). Users can control the devices by graphical
user interface (GUI). This user manual describes the hardware setting and how
to update the firmware on the Wrenboard. For the information about software
operation, please refer to “Bridgeboard Control Panel User Manual”.
Getting Started
Figure 1. The Connection of Wrenboard
Figure 1. Summarizes the purpose of Wrenboard. This section describes how to install the required components.
System requirements
- Operating system: Windows 7, or Windows 10.
Software installation
Install Richtek Bridgeboard Utilities downloaded from
http://www.richtek.com/shareEVB/RTBridgeboardUtilities.exe
Hardware installation
- Connect Wrenboard and target device via connect cable.
- Insert Wrenboard into a USB port.
Graphical User Interface
After software and hardware installation, you can run Richtek Bridgeboard
Control Panel to control the target device by GUI (Figure 2). For details
regarding the operation, please refer to “Bridgeboard Control Panel User
Manual”.
Figure 2. The GUI of Richtek Bridgeboard Control Panel
Hardware Description
-
Standard USB A plug
It can be connected to PC directly. -
Micro-B USB port
It is an alternative to connect Wrenboard to PC when the long distance between Wrenboard and PC is needed. -
I2C voltage LED
The Red LED indicates that the I2C pins are operated in 3.3V. -
I2C voltage LED
The Blue LED indicates that the I2C pins are operated in 1.8V. -
System LED
If the Wrenboard execute a command, the white LED will be switched on/ off. -
I2C voltage exchange / Firmware update button
-
To exchange I2C voltage
Click FN button in normal operation mode, the I2C voltage will be exchanged between 3.3V and 1.8V level. -
To enable firmware download mode
Connect Wrenboard to PC and press FN button. If the red and blue LEDs are blinking alternatively, it means firmware download mode is ready.
-
-
I2C and GND pins
-
SCL (Serial Clock Line)
SCL is a serial clock line with a 2.7kΩ pull-up resistor. It is used to synchronize the data transfers on the I2C bus. -
SDA (Serial Data Line)
SDA is a serial data line with a 2.7kΩ pull-up resistor. It is used to send data and address.
-
-
3V power pin
It is suggested to limit the output current within 100mA. -
1.8V power pin
It is suggested to limit the output current within 100mA. -
GPIO
The GPIO pin can be configured as GPIO (P0.1), 1-wire (GSOW) and PWM function according to programming setting. User can connect this pin to control device in either function.
Firmware Update
Step 1. Connect Wrenboard to PC
To avoid impacting the other device, please disconnect all available pins on
the Wrenboaord.
Step 2. Run Richtek Wrenboard Flasher
(Start > Richtek Technology Corporation > Richtek Bridgeboard Utilities >
Firmware Update Tool >Richtek Wrenboard Flasher)
Step 3. Use force download mode if the firmware cannot operate normally.
Otherwise go to Step 4.
Press FN button until the red and blue LEDs are blinking alternatively.
Step 4. Load firmware
Click “Load Firmware” and select the file you want to install on the
Wrenboard.
Step 5. Install firmware
Notes :
When popup following message. It is suggested to update newest firmware.
Click Richtek Auto Update Engine icon in lower right corner.
Click “Start Batch Flash” and “Make this device reboot”.
More Information
For more information, please find the related datasheet or application notes
from Richtek website http://www.richtek.com.
Important Notice for Richtek Reference Design
THIS DOCUMENT IS FOR REFERENCE ONLY, NOTHING CONTAINED IN THIS DOCUMENT SHALL
BE CONSTRUED AS RICHTEK’S WARRANTY, EXPRESS OR IMPLIED, UNDER CONTRACT, TORT
OR STATUTORY, WITH RESPECT TO THE PRESENTATION HEREIN. IN NO EVENT SHALL
RICHTEK BE LIABLE TO BUYER OR USER FOR ANY AND ALL DAMAGES INCLUDING WITHOUT
LIMITATION TO DIRECT, INDIRECT, SPECIAL, PUNITIVE OR CONSEQUENTIAL DAMAGES.
Richtek Technology Corporation
14F, No. 8, Tai Yuen 1st Street, Chupei City
Hsinchu, Taiwan, R.O.C.
Tel: (8863)5526789
Window: RDC / SRD
Copyright © 2022 Richtek Technology Corporation. All rights reserved. is a
registered trademark of Richtek Technology Corporation
RD0001-01_01 August 2022
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>