Soocas PT1 Aura Electric Toothbrush User Manual
- June 17, 2024
- SOOCAS
Table of Contents
Soocas PT1 Aura Electric Toothbrush
Specifications
- Product Name: Soocas Sonic Electric Toothbrush
- Model: PT1
- Input Power: 5V 1A
- Charging Time: 6 Hours
- Charging Method: Type-C
- Made in China
- Manufactured by: Shenzhen Soocas Technology Co., Ltd.
- Product Origin: Shenzhen, China
- Address: Room 401, 402, 1101, 1102, 1103, 1104, Building 2 Chongwen Area, Nanshan iPark, No. 3370 Liuxian Avenue, Fuguang Community, Taoyuan Subdistrict, Nanshan District, Shenzhen, China
Product Introduction
Thank you for choosing the Soocas Aura Electric Toothbrush. This user
manual will provide you with detailed information on how to use and care for
your oral health.
Operating Guide
Installing Brush Head: Ensure that the bristle direction of the toothbrush head is aligned with the front of the toothbrush handle. Gently push the toothbrush head onto the motor shaft. Note that there will be a small gap between the toothbrush head and the handle to reduce friction.
To Turn On/Off and Pause: The toothbrush offers multiple cleaning modes:
- Soft: Gentle brushing for new and sensitive users.
- Gum Protection: Comfortable and powerful mode that protects and improves gum health.
- Cleaning: Fulfills the daily requirements of most users.
- Brightening: Intensive cleaning power that restores natural brightness.
- Polishing: High oscillation of the brush head for deep scrubbing of stubborn stains.
Battery Reminder Lamp: The red light indicates low power and prompts you to charge the toothbrush. A red or green light flashing indicates that the device is currently charging. A green light indicates that the equipment is fully charged.
Zone Change Reminder: Every 30 seconds, the toothbrush will vibrate to pause and remind you to replace the brushing position.
Proper Brushing Techniques:
- Guide the brush head slowly from tooth to tooth with a 40-degree angle between the bristles and the gum lines.
- Press the On/Off button to select the preferred brushing mode.
- The toothbrush will vibrate to indicate when to brush a new area of the mouth.
- Keep the brush head close to the teeth without bending the bristles.
ChargingInstructions
- The Soocas Aura Electric Toothbrush has a built-in rechargeable battery that takes approximately 6 hours to fully charge. The actual charging time may vary depending on the remaining power and charging environment.
- The battery temperature should be between 0°C and 45°C before charging.
Environmental Protection
- To open the handle tail cover, insert a flathead screwdriver into the gap between the handle tail cover and the main body. Pry it upward until the tail cover opens for the left and right locking positions.
- Press one end of the shaft against the desktop and apply downward force.
- While performing the previous step, pry out the symmetrical two locking positions of the inner bracket with a flathead screwdriver. Apply downward force while holding the machine body to push out the movement.
FAQ
Q: How long does it take to fully charge the Soocas Aura Electric
Toothbrush?
A: The Soocas Aura Electric Toothbrush takes approximately 6 hours to
fully charge.
Q: What are the different cleaning modes available on the toothbrush?
A: The toothbrush offers multiple cleaning modes, including Soft, Gum
Protection, Cleaning, Brightening, and Polishing.
Q: How do I know when to replace the brushing position?
A: The toothbrush will vibrate every 30 seconds to pause and remind you
to replace the brushing position.
Q: Can I charge the toothbrush in any environment?
A: The toothbrush should be charged in an environment with a temperature
between 0°C and 45°C.
Thank you for choosing Soocas oral care series: Soocas Aura Electric
Toothbrush.
Please read this manual carefully and the correct method of usa ge for Soocas
Aura Electric Toothbrush to fully understand its perform ance to better clean
and care for your oral health.
-
Product Name: Soocas Sonic Electric Toothbrush
-
Model: PT1
-
Input Power: 5V 1A
-
Charging Time: 6 Hours
-
Charging Method: Type-C
-
Made in China
Manufactured by: Shenzhen Soocas Technology Co., Ltd. -
Product Origin: Shenzhen, China
-
Address: Room 401, 402, 1101, 1102, 1103, 1104, Building 2 Chongwen Area, Nanshan iPark, No. 3370 Liuxian Avenue, Fuguang Community,Taoyuan Subdistrict, Nanshan District, Shenzhen, China
All products bearing this symbol are waste electrical and electronic equipment
(WEEE as in directive 2012/19/EU) which should not be mixed with unsorted
household waste.
Instead, you should protect human health and thee environment by handing over
your waste equipment to a designated collection point for the recycling of
waste electrical and electronic equipment, appointed by the government or
local authorities.
Correct disposal and recycling will help prevent potential negative
consequences to the environment and human health. Please contact installer or
local authorities for more information about the location as the well as terms
and conditions of such collection points.
Safety Tips
When using this product for the first time, it is common to experience minor discomfort with some gum bleeding. This is because the gums are not quite used to the high-vibration cleaning method. It is recommended to use gentle mode for beginners and expects this discomfort to continue for 1-2 weeks upon initial usage. If bleeding persists for longer than 2 weeks, please stop using the product immediately and consult professional assistance from your dentist.
Warning
-
For users with teeth correction, dental repair, dental implants, etc., please use this product under the guidance of a dentist or doctor.
-
This product meets the safety standards of electromagnetic devices.
For any issues related to pacemakers or other implantable devices, please consult a doctor or the manufacturer of the implant before use. -
This product is only designed for cleaning teeth, gums, and the tongue. Do not use it for any other purpose. If you feel any discomfort or pain, please stop using this product and seek professional assistance from a dentist or a doctor.
-
Do not immerse the charging port in water or any liquid.
-
Do not plug in the power supply if there is liquid on the charging port or power plug.
-
This product has a built-in rechargeable battery. Do not throw it into the fire or charge it in a high-temperature environment.
-
Do not knock or drop this product. If the product is damaged due to collision or falling, please stop using it.
-
Do not modify, disassemble or repair this product by yourself.
-
This device is not suitable for people with physical, sensory, or mental disabilities, and lack of experience and knowledge (including children) to use unless they are supervised or instructed by a person responsible for their safety.
-
Children should not play with this product.
-
Cleaning and maintenance should not be done by children without supervision.
-
Use a safe and compliant power adapter for charging.
Cautious
- Please check for obvious damage before using the product. Do not use it if it is damaged or the machine has suffered a severe fall.
- Make sure that the charging port and charging cable are dry before charging; otherwise, it may cause an electric shock or short circuit.
- This product has a built-in battery, do not throw it into the fire.
- Do not place it in a high-temperature or damp place, and avoid direct sunlight.
- The charging base cannot be used in outdoor direct sunlight.
- Do not use the toothbrush when soaking in a bath or shower.
- Do not share the brush head with others. Do not place metal objects on the charging base while it is powered on.
- Note: The product and accessory illustrations in the manual are for reference only. Due to product updates and upgrades, the actual product may differ slightly from the illustration. Please refer to the actual product.
- This product is intended for home use only. Do not use it in ac commercial setting.
Product Introduction
Operating Guide
To Charge
- Please charge first before using it for the first time. Please us e the 5V 1A charging adapter.
Installing Brush Head
Ensure the bristle direction of the toothbrush head is aligned with the front of the toothbrush handle, then push the toothbrush head o into the motor shaft gently. Note that there will be a small gap between the toothbrush head and the handle to reduce friction between the tw o parts from the vibration of the motor.
To Turn On/Off and Pause
Key Function
- Short press to start the device.
- Short press the Power Switch within 15 seconds after startup to switch speeds. Short press the switch key within 15 seconds after startup to shut down.
- In the startup state: Press and hold for 2 seconds to pause. If no action occurs within 30 seconds, the device will shut down, and if the Power Switch is pressed once again within 30 seconds, the device will once again start up and continue the countdown of the last action after the device is switched on.
Cleaning Modes
- Soft: Gentle brushing, caring for new and sensitive users
- Gum Protection: Comfortable and powerful, protects and improves gum health
- Cleaning: Fulfills the daily requirements of most users
- Brightening: Intensive cleaning power, restores the natural brightness Polishing: High oscillation of the brush head for deep scrubbing of stubborn stains
Battery Reminder Lamp
- Red light on: Low power, please charge in duetime
- Red or green light flashing: Device is charging
- Green light on: The equipment is fully charged
Zone Change Reminder
- Every 30 seconds, it vibrates to pause and to remind replacing the brushing position.
Proper Brushing Techniques
- Guide the brush head slowly from tooth to tooth with a 40-degree angle between the bristles and the gum lines.
- Press the On/Off button for the preferred brushing mode.
- The toothbrush will vibrate to indicate the user has to brush a new area of the mouth.
- Keep the brush head to the teeth closely without bending the bristles.
Charging Instructions
- Soocas aura acoustic electric toothbrush has a built-in rechargeable battery, which takes about 6 hours to fully charge. The specific charging time may vary depending on the remaining power and charging environment.
- Battery temperature should be 0 ~ 45 ℃ before charging.
Environmental Protection
When the product is at the end of its service life, according to local laws
and regulations, one must remove the internal battery and undergo proper
recycling and disposal procedures before the parts can be disposed of. If you
are having trouble displacing the battery, please dispose of the product in
accordance with the local waste clarification regulation.
Warning
- Do not throw batteries into the fire to prevent battery explosion or the release of toxic and harmful substances.
- Do not short-circuit the battery to prevent battery combustion and fire.
- Unless the intention is to discard the product, do not disassemble the product parts to prevent damaging the product.
- Strict safety procedures must be taken place. Before removing the battery, the power connection must be disconnected.
- Before discarding the product, the battery must be removed from the product.
- The product must be powered off when removing the battery.
- Batteries should be disposed of safely.
Remove the rechargeable battery
- Use a flathead screwdriver to pry open the handle end cap.
- Detach the cover and use a flathead screwdriver to pray open the inner motor. Pop out the motor.
- Cut the red wires on the inner motor.
- Insert a flathead screwdriver into the gap between the handle tail cover and the main body, and pry it upward until the tail cover opens for the left and right locking positions.
- Press one end of the shaft against the desktop and apply downward force.
- When performing the 2nd step, pry out the symmetrical two locking positions of the inner bracket with a flathead screwdriver, and apply downward force while holding the machine body to push out the movement.
- Use diagonal pliers to cut it forcibly between the plastic and PCB plate at the point indicated by the arrow until the battery solder feet are cut.
- Take out the battery and put it in the designated recycling place.
Troubleshooting
