RICHTEK RTQ2539CGQWF Evaluation Board User Guide
- June 13, 2024
- RICHTEK
Table of Contents
- RICHTEK RTQ2539CGQWF Evaluation Board
- General Description
- Performance Specification Summary
- Power-up & Measurement Procedure
- Detailed Description of Hardware
- Typical Applications
- Measure Result
- Evaluation Board Layout
- More Information
- Important Notice for Richtek Evaluation Board
- References
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
RICHTEK RTQ2539CGQWF Evaluation Board
Specifications
The RTQ2539C Evaluation Board (EVB) is a high-current, ultra-low noise, ultra
low-dropout (LDO) linear regulator with the following key features:
- Input Voltage Range: 1.1V to 6.5V
- Output Voltage Range: 0.5V to 5.5V
- Line Regulation: 0.05% per Volt
- Load Regulation: 0.08% per Ampere
- Dropout Voltage: 55mV to 130mV
- Package: WQFN-12L 2.2×2.5 (FC)
Suggested Equipments
- RTQ2538H evaluation board
- DC power supply capable of at least 6.5V and 3A
- Electronic load capable of 3A
- Function generator
Notifications
- Do not turn on input power supply before all connections are ready.
- Avoid using oscilloscope probe with long ground lead for output ripple voltage measurement.
Detailed Description of Hardware
Headers Description and Placement:
Carefully inspect all components according to the Bill of Materials table
to ensure correct installation and no damage.
Test Points
| Test Point | Pin Name | Description |
|---|---|---|
| GP1 | VIN | Positive terminal for supply input voltage. |
| GP2 | GND | Negative terminal for supply input voltage. |
| GP3 | VOUT | Positive terminal for output voltage. |
| GP4 | GND | Negative terminal for output voltage. |
Frequently Asked Questions (FAQ)
Q: What should I do if I encounter issues with output voltage regulation?
A: Check the load and ensure it is within the specified range. Verify the
connections and components for any faults or errors.
Evaluation Board
General Description
The RTQ2539C is a high-current, ultra-low noise, ultra-low-dropout (LDO) linear regulator. This document explains the function and use of the RTQ2539C evaluation board (EVB) and provides information for the setup and operating instructions, a schematic diagram, a printed circuit board (PCB) layout, and a bill of materials (BOM). For more detail information, please refer to the RTQ2539C datasheet.
Performance Specification Summary
The RTQ2539C Evaluation Board (EVB) is a four-layer board measuring 50mm x
33.5mm with a copper thickness of 1oz, and the Table 1 is the summary of the
EVB performance specification.
Table 1. RTQ2539C Evaluation Board Performance Specification Summary
| Key Features | Test Conditions | Min | Typ | Max | Unit |
|---|
Input Range
Input Voltage| | 1.1| 1.1| 6.5| V
Enable Input Voltage| | 1.1| —| 6.5| V
Output Range
Output Voltage| Using external resistive voltage divider| 0.5| 0.5| 5.5| V
Line Regulation| IOUT = 1mA, 1.1V ≤ VIN ≤ 6.5V| —| 0.05| —| %/V
Load Regulation| 1mA ≤ IOUT ≤ 3A| —| 0.08| —| %/A
Dropout Voltage| VIN = 1.1V to 6.5V, IOUT = 3A, VFB = 0.5V – 3%| —| 55| 130|
mV
Package
WQFN-12L 2.2×2.5 (FC)
Power-up & Measurement Procedure
Suggestion Required Equipments:
- RTQ2538H evaluation board
- DC power supply capable of at least 6.5V and 3A
- Electronic load capable of 3A
- Function generator
- Oscilloscope
Test Procedure with Suitable Measurement Equipment:
- Connect input power supply with wide and short as possible to VIN and GND through GP1/GP2 terminals.
- Connect the electronic load to VOUT and GND through GP3/GP4 terminals.
- Turn on the power supply and make sure that the input voltage does not exceeds 6V.
- Check output voltage regulation with different IOUT for normal operation.
Notifications:
- Do not turn on input power supply before all connections are ready.
- Do not use the oscilloscope probe with long ground lead for output ripple voltage measurement, it is recommended to touch the probe tip and groundring directly across the last output capacitor.
Detailed Description of Hardware
Carefully inspect all the components used in the EVB according to the following Bill of Materials table, and then make sure all the components are undamaged and correctly installed. If there is any missing or damaged component, which may occur during transportation, please contact our distributors or e-mail us at evb_service@richtek.com
Test Points
The EVB is provided with the test points and pin names listed in the table
below.
| Test Point | Pin Name | Description |
|---|---|---|
| GP1 | VIN | Positive terminal for supply input voltage. |
| GP2 | GND | Negative terminal for supply input voltage. |
| GP3 | VOUT | Positive terminal for output voltage. |
| GP4 | GND | Negative terminal for output voltage. |
| GP5 | GND | Reference ground test point. |
| TP1 | VIN | For supply input voltage measurement. |
| TP2 | EN | Enable voltage input pin. |
| TP3 | PGOOD | For power good measurement. |
| TP4 | VOUT | For output voltage measurement. |
| JP1 | Enable | Connection for Enable voltage. |
| JP2 | PGOOD | Connection for power good pu-ll high voltage. |
Bill of Materials
| Reference | Count | Part Number | Description | Package | Manufacturer |
|---|---|---|---|---|---|
| U1 | 1 | RTQ2539CGQWF | Linear Regulator | WQFN-12L 2.2×2.5 (FC) | RICHTEK |
| C3, C6 | 2 | 1210X476K160CT | Capacitor, Ceramic, 47µF, 16V, X5R | C-1210 | WALSIN |
| C4, C5 | 2 | 0603B104K500CT | Capacitor, Ceramic, 0.1µF, 50V, X7R | C-0603 | WALSIN |
| C9, C11 | 2 | 0603B103K500CT | Capacitor, Ceramic, 10nF, 50V, X7R | C-0603 | WALSIN |
| C10 | 1 | 0603B105K250CT | Capacitor, Ceramic, 1µF, 25V, X5R | C-0603 | WALSIN |
| R1 | 1 | WR06X1072FTL | Resistor, Chip, 10.7k, 1% | R-0603 | WALSIN |
| R2 | 1 | WR06X1911FTL | Resistor, Chip, 1.91k, 1% | R-0603 | WALSIN |
| R3, R5 | 2 | WR06X1003FTL | Resistor, Chip, 100k, 1% | R-0603 | WALSIN |
Typical Applications
EVB Schematic Diagram
Measure Result
Evaluation Board Layout
Figure 1 to Figure 4 are the RTQ2539C evaluation board layout.
More Information
For more information, please find the related datasheet or application notes from Richtek website http://www.richtek.com
Important Notice for Richtek Evaluation Board
THIS DOCUMENT IS FOR REFERENCE ONLY, NOTHING CONTAINED IN THIS DOCUMENT SHALL BE CONSTRUED AS RICHTEK’S WARRANTY, EXPRESS OR IMPLIED, UNDER CONTRACT, TORT OR STATUTORY, WITH RESPECT TO THE PRESENTATION HEREIN. IN NO EVENT SHALL RICHTEK BE LIABLE TO BUYER OR USER FOR ANY AND ALL DAMAGES INCLUDING WITHOUT LIMITATION TO DIRECT, INDIRECT, SPECIAL, PUNITIVE OR CONSEQUENTIAL DAMAGES.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>