ZKTECO SBTL6000 Series Swing Barrier User Manual

: June 6, 2024
: ZKTECO

User Manual
Swing Barrier-SBTL6000 Series
Date: August 2020
Doc Version: 2.1

Thank you for choosing our product. Please read the instructions carefully before operation. Follow these instructions to ensure that the product is functioning properly. The images shown in this manual are for illustrative purposes only.
For further details, please visit our Companys’s website www.Zkteco.com.

Copyright © 2020 ZKTECO CO., LTD. All rights reserved.
Without the prior written consent of ZKTeco, no portion of this manual can be copied or forwarded in any way or form. All parts of this manual belong to ZKTeco and its subsidiaries (hereinafter the “Company” or “ZKTeco”).

Trademark

ZkTeco ncreco is a registered trademark of ZKTeco. Other trademarks involved in this manual are owned by their respective owners.

Disclaimer
This manual contains information on the operation and maintenance of the ZKTeco equipment. The copyright in all the documents, drawings, etc. in relation to the ZKTeco supplied equipment vests in and is the property of ZKTeco.

The contents hereof should not be used or shared by the receiver with any third party without express written permission of ZKTeco. The contents of this manual must be read as a whole before starting the operation and maintenance of the supplied equipment. If any of the content(s) of the manual seems unclear or incomplete, please contact ZKTeco before starting the operation and maintenance of the said equipment.

It is an essential pre-requisite for the satisfactory operation and maintenance that the operating and maintenance personnel are fully familiar with the design and that the said personnel have received thorough training in operating and maintaining the machine/unit/equipment. It is further essential for the safe operation of the machine/unit/equipment that personnel has read, understood and followed the safety instructions contained in the manual.

In case of any conflict between terms and conditions of this manual and the contract specifications, drawings, instruction sheets or any other contract- related documents, the contract conditions/documents shall prevail. The contract-specific conditions/documents shall apply in priority.
ZKTeco offers no warranty, guarantee or representation regarding the completeness of any information contained in this manual or any of the amendments made thereto. ZKTeco does not extend the warranty of any kind, including, without limitation, any warranty of design, merchantability or fitness for a particular purpose.
ZKTeco does not assume responsibility for any errors or omissions in the information or documents which are referenced by or linked to this manual. The entire risk as to the results and performance obtained from using the information is assumed by the user.

ZKTeco in no event shall be liable to the user or any third party for any incidental, consequential, indirect, special, or exemplary damages, including, without imitation, loss of business, loss of profits, business interruption, loss of business information or any pecuniary loss, arising out of, in connection with, or relating to the use of the information contained in or referenced by this manual, even if ZKTeco has been advised of the possibility of such damages.

This manual and the information contained therein may include technical, other inaccuracies or typographical errors. ZKTeco periodically changes the information herein which will be incorporated into new additions/amendments to the manual. ZKTeco reserves the right to add, delete, amend or modify the information contained in the manual from time to time in the form of circulars, letters, notes, etc. for better operation and safety of the machine/unit/equipment. The said additions or amendments are meant for improvement /better operations of the machine/unit/equipment and such amendments shall not give any right to claim any compensation or damages under any circumstances.

ZKTeco shall in no way be responsible (i) in case the machine/unit/equipment malfunctions due to any non-compliance of the instructions contained in this manual (ii) in case of operation of the machine/unit/equipment beyond the rate limits (iii) in case of operation of the machine and equipment in conditions different from the prescribed conditions of the manual.

The product will be updated from time to time without prior notice. The latest operation procedures and relevant documents are available on http://www.Zkteco.com
If there is any issue related to the product, please contact us.

ZKTeco Headquarters
Address ZKTeco Industrial Park, No. 26, 188 Industrial Road,
Tangxia Town, Dongguan, China.
Phone +86 769 – 82109991
Fax +86 755 – 89602394 For business-related queries, please write to us at:sales@oktero.com.
To know more about our global branches, visit www.zkteco.com.

About the Company

ZKTeco is one of the world’s largest manufacturers of RFID and Biometric (Fingerprint, Facial, Finger-vein) readers. Product offerings include Access Control readers and panels, Near & Far-range Facial Recognition Cameras, Elevator/floor access controllers, Turnstiles, License Plate Recognition (LPR) gate controllers and Consumer products including battery-operated fingerprint and face-reader Door Locks. Our security solutions are multi-lingual and localized in over 18 different languages. At the ZKTeco state-of-the-art 700,000 square foot 1509001-certified manufacturing facility, we control manufacturing, product design, component assembly, and logistics/shipping, all under one roof.

The founders of ZKTeco have been determined for independent research and development of biometric verification procedures and the productization of biometric verification SDK, which was initially widely applied in PC security and identity authentication fields. With the continuous enhancement of the development and plenty of market applications, the team has gradually constructed an identity authentication ecosystem and smart security ecosystem, which are based on biometric verification techniques. With years of experience in the industrialization of biometric verifications, ZKTeco was officially established in 2007 and now has been one of the globally leading enterprises in the biometric verification industry owning various patents and being selected as the National High-tech Enterprise for 6 consecutive years. Its products are protected by intellectual property rights.

About the Manual

This manual introduces the operations of the SBTL6000 Series product.
All figures displayed are for illustration purposes only. Figures in this manual may not be exactly consistent with the actual products.

Document Conventions

Conventions used in this manual are listed below:
GUI Conventions

For Softa

Convention| Description
Bold font| Used to identify software interface names e.g. OK Confirm, Cancel >

| Multilevel menus are separated by these brackets. For example, File > Create > Folder.

ak-

For Device

Convention| Description

< >| Button or key names for devices. For example, press [ ]| Window names, menu items, data table, and field names are inside square brackets. For example, pop up the [New User] window ⁄| Multilevel menus are separated by forwarding slashes. For example, [File/Create/Folder].

Symbols

Convention	Description
This implies about the notice or pays attention to, in the manual
The general information which helps in performing the operations faster
The information which is significant
Care taken to avoid danger or mistakes
The statement or event that warns of something or that serves as a

cautionary example.

Product Introduction

Model Number and Access Control

Access Model| None| C3-200 and Two
KR800E reader| InBio 260 and Two
FR1500 reader| Two visible light
products
---|---|---|---|---
SBTL6000| √| | |
SBTL6011| | √| |
SBTL6022| | | √|
SBTL6033| | | | √
SBTL6200| √| | |
SBTL6211| | √| |
SBTL6222| | | √|
SBTL6233| | | | √

Chassis Design and Dimensions

SBTL6000 series comes with SUS304 housing which provides a simple and beautiful design with corrosion protection. It provides legal access to the persons and restricts illegal personnel access. In case of emergency, it ensures that evacuation passage runs smoothly and is convenient for personnel.
SBTL6000’s appearance and dimensions are shown in Figure 1-1:

Mechanical System of the Swing Barrier

The mechanical system of a swing barrier turnstile includes the chassis and the core component. The chassis is a carrier where the direction indicator, the reader, the Infrared sensor, and the door lock are installed. The core component mainly consists of the motor, the frame, the belt, and the swingarm.

Electronic control system

The electronic control system of a swing barrier turnstile is mainly composed of the reader, the master control panel, the infrared sensor, the direction indicator and the alarm.

Reader: The reader reads the data in the card and sends it to the controller.
Master control panel: The master control panel is the system’s control center that receives signals from the reader and the photoelectric switch, performs logical judgment and processing of these signals, and sends executive commands to the direction indicator, the electric motor, and the alarm.
Infrared sensor: It detects the position of a pedestrian and plays the role of safety protection.
Direction indicator: This indicator displays the pedestrian passage path, and directs them to pass through the lane in a safe and orderly manner.
Alarm: The alarm gives an alarmed voice if the system detects any unauthorized entry to the lane.

Working Principle of Swing Barrier

After supplying power to the device, the system performs self-check. The device starts normally if no failure is detected. If a failure is detected, the system displays related messages on the LCD display screen so that the user can have a quick knowledge of and solve the problem.
When the reader detects a valid card, the buzzer will give a positive audible prompt to the pedestrian, indicating that the card is being read successfully. And then, the reader sends signals to the access controller to request permission to pass through the lane. The access controller will send the signal to the master control panel.
After receiving the signal from the access controller, the master control panel sends valid control signals to the direction indicator and the electric motor. At last the direction arrow turns green.
Pedestrians pass through the lane according to the direction indicator signs. Infrared sensors keep on detecting the pedestrian during the whole process, and continue to send signals to the master control board until the pedestrian passes completely through the lane.
If the pedestrian enters the passage but forgets to flash the card, or if the card held by the pedestrian is invalid, the system will prompt an audible alarm to stop and retreat the pedestrian from the lane The pedestrian can pass through the lane only after a valid card is read by the card reader.

System Composition of the Product

The single-lane management system is composed of two single-core swing barriers. The multi-lane management system is composed of two single-core barriers and multiple dual-core barriers.

Working modes of the system
To make the product more versatile, this system provides multiple working modes for the user, including normal working mode, normally open and normally close mode, testing mode. After supplying power to the device, the LCD screen on the control board will display a default state, which displays the current work mode.

Specification

Dimension(mm)	SBTL6000 Series: L = 1400, W = 180, H =1000
Communication	RS485
Input control signal	Switching signal

Installation of the Product

Installation Notes

It is recommended that the swing barrier must be installed on a horizontal solid platform with a height of 50mm to 100mm.
It is also recommended that the swing barrier turnstile should not be used in corrosive environments.
Make sure the protective ground wire of the system is reliably connected to avoid personal injuries or other accidents.
After installation, check if the connection is done correctly at the connecting points of the protective ground wire, at the connector assemblies and wiring points of the circuits, as well as at each movable part of the swing barrier turnstile. Any loose nuts, screws and other fasteners should be tightened in time to avoid swing barrier turnstile failures caused by longer operations.

Installation Position of the Swing Barrier

A distance of 100mm between the swing barrier turnstile and the wall needs to be reserved for ease of opening the top cover of the machine to perform maintenance and adjustment. The reference figure is shown below:

Cables Installation and Fixing

For the outlets of the concealed cables, please refer to the drawing indicating the mounting holes. The input voltage for this swing barrier turnstile is AC100-120V/200-240V and its master and slave are connected by a 5-core cable (signal) and a 2-core cable (power). When installing the swing barrier turnstile, the user only needs to connect it to the corresponding ports. Note that the PVC conduits are laid 100mm under the ground, with the height of the exposed part not exceeding 100mm. In addition, the conduit outlet is bent back to prevent ingress of water into the conduit.
SBTL6000 series installation holes and cabling positions is shown in Figure 2-2:

Mark the screw hole at the center of the stand, and the edge of the chassis base on the ground according to the sizes as shown on the Figure 2-2. Use a hammer drill to make M12 screw holes and then install the screws. Place the swing barrier turnstile according to the sizes and positions as shown in the figure before installation and fixing. Connect the online cables and perform the power-on test. If the test is OK, tighten the screws. It is recommended that a warning line be marked on the ground after installing the device, so as to prompt the pedestrian to stand behind the warning line when swiping the card. As shown in Figure 2-3:

Function Introduction

After powered on, the LCD screen on the control board will display the default state showing the current working model.
There are 4 buttons on the control board:
UP, DOWN, ENT, and ESC, show in Figure 3-1: UP: to move upwards or increase the value.
DOWN: to move downwards or decrease the value.
ENT: to enter a menu setting item or confirm the current modified value.
ESC: to return to the previous menu or cancel the current operation.

3. Operation and instruction of menu
Press the ENT button and enter the password input interface. The default password is UP, UP, DOWN, DOWN, DOWN, DOWN. You may press the ESC button to erase the last input. After entering the menu, press UP or DOWN to choose a menu item, then press ENT to enter the interface and adjust such function or value.
There are four keys on the control panel, including “UP”, “DOWN”, “ENT”, and “ESC”. Press “ENT” to modify settings, press the “UP” and “DOWN” buttons to select a function, and press “ESC” to exit.

Menu Introduction

After inputting the correct password then press “OK” and the menu operation interface is displayed. The menu has the following options:

Barrier positioning
Zero position (Default).
Left opening position.
Right opening position.
Opening mode
Bi-direction swiping card. (Default)
Left free + Right swiping card.
Left swiping card + Right free.
Bi-direction control by IR sensor.
Left forbidden + Right swiping card.
Left swiping card + Right forbidden.
Left forbidden + Right free.
Left free + Right forbidden.
Bi-direction forbidden.
Open duration
5-60s (The default is 10s).
False direction entry
Close door and voice alarm.
Voice alarm (Default).
Alarm disabled.
Speed of barrier closing and opening
Low speed.
Middle speed (Default).
High speed.
Anti-tailgate
The alarm is disabled.
Voice alarm (Default).
Close door and voice alarm.
Reset counter
Exit counter (Default).
Entry counter. Both.
Gate closing delay time
0-10s (The default is 0).
Unlock brake Delay to unlock (Default).
Unlock after card swiping.
Brake starting angle
3-10° (The default is 3′ ).
Fire signal setting
Right opening (Default).
Left opening.
Disable.
System working mode (Default).
Test mode.
Factory reset.
Volume setting
Disable.
1-16(The default is 5).
Exchange voice of door opening
No (Default).
Yes.
IR anti-pinch setting
Disable.
Stop turning for anti-pinch (Default).
Open the barrier for anti-pinch.
Memory function
Disable (Default).
Enable.
Select anti-pinch area
No anti-pinch (Default).
All IR areas for anti-pinch.
Master device speed compensation
0-20 (The default is 0).
Slave device speed compensation
0-20 (The default is 0).
Swiping card mode
Allow swiping the card in the passage (Default).
Not allowed swiping card in the passage.
. Version
V6.0.4.

Troubleshooting

Number	Failure description	Analysis and solution
1	No response from direction indicator or indication is not correct.	Check

whether the connection of the roof lamp is correct or not.
2| After swiping the card, there is only a swing arm action.| Check the master and slave machine type setting and the 5-core, 2-core connection line.
3| Delay in barrier opening doesn’t close.| Check whether the time of the opening is too long or the IR sensor is covered.
4| The motor doesn’t rotate, the resistance is much, or the belt is loose.| The motor works properly, but the rotated angle is not sufficient, so it may cause loosening of the belt.
5| When powered ON, the swing doesn’t return to the initial position.| Ensure that no obstacle is in the sensing area, then restart the equipment.

Product Maintenance

Chassis Maintenance

The chassis is made up of SAE 304 stainless steel. If it is in service for a longer period, then there may be rust stains on its surface, regularly sand the surface along the grain softly and carefully. Coat the surface with anti- rust oil, do not cover the infrared sensor.

Movement Maintenance

Switch off the power supply before maintenance. Open the door, clean surface dust, lubricate the transmission mechanism. Check the belt movement, if found loose, adjust the position of the motor to tighten the belt. Check and tighten others connection parts.

Power maintenance

Switch off the power supply before maintenance. Check the plug connection, if found loose, fix it properly. Do not change any connection position randomly. Check the external power supply insulation periodically. Do periodic checks for any kind of leakage. Check if the technical parameters of the interface are normal. Check the service life of the electronic components and replace accordingly.
Caution: Above mentioned maintenance method for the swing barrier must be carried out by professional personnel. Especially the movement and the electric control part, first switch off the power supply, ensure the operation safety.

Appendix Internal Wiring Diagram

https://www.zkteco.com/en/

ZKTeco Industrial Park, No. 26, 188 Industrial Road,
Tangxia Town, Dongguan, China.
Phone :+86 769 – 82109991 Fax : +86 755 – 89602394
www.zkteco.com
Copyright © 2020 ZKTECO CO., LTD. All Rights Reserved.