Bellababy BLA8042 Wearable Breast Pump User Manual

Bellababy BLA8042 Wearable Breast Pump

Please read the user manual carefully to ensure you have the best experience.

(Question?)

Contact Bellababy service team at

• Service-US@Bellababy-med.com
• Service-EU@Bellababy-med.com
• Service-JP@Bellababy-med.com

Symbols & Meanings

• Product serial number(The first 5 digits are the year and month.and the last 6digits are the serial number.)
• Manufacturer name and address
• Please refer to the instruction manual
• Waste electrical materials should be sent to a dedicated collection point for recycling
• The level of dust and water repellency
• Applied parts: Type BF
• DC symbol

Read before Use

1. Hold the (9 for 3~5 seconds to turn on or turn off, press the to switch modes
2. The device is intended for a single user. Use by more than one person may bring health risk and voids the warranty.
3. The washable parts must be cleaned and sterilized before first use. They should be replaced when worn down or damaged. Replacement parts are available at www.amazon.com/bellababy
4. Fully charge the Hub before the first use. Do not use while charging or low battery.
5. Recharge the Hub regularly (at least 1 time per month)to keep the battery active when it is left unused for long term.
6. The operating life of the Hub is defined to be approximately 400 hours.
7. Do not immerse or rinse the Hub in water or other liquids.just wipe it by a clean, damp cloth. If milk or water spills on the operating panel, wipe it immediately. The Hub is not waterproof.
8. Make sure every part is assembled correctly and tightly before use. Any question about assembling needed assistance please contact with Bellababy service team for assistance.
9. Do not overload milk to prevent spill while pour in bottle.
10. Any problem arises during use please contact us at Service-US@Bellababy-med.com 

The Parts

Tip: The replaceable parts should be replaced when they are worn down or damaged. If your need extra parts or to replace the parts, please visit Bella baby store: www.amazon.com/bellababy or contact us at Service-US@Bellababy-med.com

1. Hub
2. Milk Collector/Breast Shield
3. Membrane
4. Connector
5. Valve
6. Silicone Flange

Know Your Pump

• Stimulation mode: The default mode when turn on.slighter and faster pumping rhythm for stimulation. Friendly for new moms.
• Expression mode: Slower rhythm but stronger and more efficient, suitable for new and experienced moms.
• Variation mode: The rhythm varies during pumping, suitable for experienced moms.
• Depth mode: The intensity gets stronger, then release, suitable for experienced moms.

How to Disassemble

1. Pull up and detach the Hub.
2. Take off the silicone flange.
3. Pull out the connector with a little muscle.
4. Detach the membrane and valve.

How to Assemble

1. Set the membrane and valve to the connector.
2. Set the connector into the milk collector.the ears of connector should be buckled completely in the indention in the milk collector.
3. Attach the silicone flange to the milk collector, the indention on the flange should match the vent on the milk collector.
4. Pinch and press the silicone flange edge all around to ensure it is attached to the milk collector closely and tightly.no air leak.
5. Connect the Hub with milk collector.pay attention to the direction.the charging port on the Hub should be outward.

How to Pour Milk

Detach the Hub then pour milk out from the spout.

Cleaning and Sterilization

Note: Except the Hub, the other parts should be cleaned and sterilized before the first use. Wipe the Hub with a clean, damp cloth. Clean and air dry the parts after every use to prevent the build-up of milk residue, which may cause bacteria growth.

Washable parts:

Cleaning

1. Rinse in clear, cold water to remove milk residue.
2. Wash in warm water with mild dish washing fluid.
3. Rinse with clear, cold water to clean thoroughly. Or:Place on the top shelf of the dishwasher.

Sterilization:

Boil in water for 5 minutes. Or:

1. Sterilize the parts with steam for 5 minutes.
2. Microwave with medium heat for no more than 5minutes.
   Please make sure every part is dry completely before use, moisture may damage the inside circuit board and battery.

How to Charge

1. Use the original Type-c cord to charge your pump, if the cord missing please order a replacement from Bellababy Amazon Store or contact the service team for assistance.
2. Recharge your pump regularly (at least once per month) to keep the battery active when the pump is left unused for long term.
3. Stop using when battery is low to extend the battery life.
4. DO NOT get the charging port wet, if milk/water spills in the port accidentally, stop charging and wipe it until dry.

Plug the USB into a computer, power bank or USB adapter.

Silicone Flange Sizing

1. This wearable pump comes with a silicone pad in 24mm, if it doesn’t fit you well, please find the 21 mm or 28mm available through www.amazon.com/bellababy.
2. Using silicone pad that doesn’t fit may lead to pain and injury. To determine the correct size, follow the below steps:

Tip: Lanolin cream can be used for lubrication to reduce the likelihood of sore nipples

Note: Lactation Women’s bodies may change during the pumping life cycle, silicone pad in other size may become a better fit.

Aligning Your Nipples

Your nipple should be positioned correctly in the silicone pad tunnel before pumping to avoid discomfort and pain. There are no two nipples point in the same direction. Align the silicone pad to the direction of your nipples when you are putting it on.

Important Safeguards

When using electrical products, especially when children are present. basic safety precautions should always be followed.

DANGER: To reduce the risk of electrocution:

• Do not use while bathing.
• Do not place or store product where it can fall or be pulled into a tub or sink.
• Do not place or drop into water or other liquid.
• Do not reach for a product if it has fallen into water. Unplug immediately.

WARNING: To avoid fire, electrocution, or serious bums:

• Danger of electrocution1 Keep the device dry! Never immerse in water or other liquids! Do not run water over the pump.
• The Bellababy breast pump and accessories are not heat-resistant: keep away from radiators and open flames.
• Keep the power adaptor away from heated surfaces.
• Do not reach for any electrical device if it has fallen into water. Unplug immediately.
• The Bellababy breast pump should never be left unattended when plugged into a power source.
• Never operate an electrical device if it has a damaged cord, plug or battery pack, if it is not working properly, if it has been dropped or damaged, or dropped into water. If damage is found, immediately discontinue use of power adaptor or battery pack and contact with Bellababy Customer service team at service-us@bellababy-med.com.
• Do not use the Bellababy breast pump while bathing or showering.
• Close supervision is necessary when the Bellababy breast pump is used in the vicinity of children.
• Only use the original charging cord with the Bella baby breast pump.
• Make sure the voltage of the power adaptor is compatible with the power source.

WARNING: To avoid health risk and reduce the risk of injury:

• Repairs must be performed only by an authorized service agency. Do not repair yourself! No modifications to the device are permitted.
• Never use a damaged device. Replace damaged or worn parts.
• Use the Bellababy breast pump only for its intended use as described in this manual.
• Do not use the Bellababy breast pump while sleeping or overly drowsy.
• This is a single user product. Use by more than one person may present a health risk.
• Do not drive while pumping.
• Inspect all appropriate pump components before each use.
• Do not thaw frozen breast milk in a microwave or in a pan of boiling water.
• If any part becomes moldy, discontinue use and replace it.
• Never use while pregnant, as pumping can induce labor.
• Clean and sanitize all parts that come into contact with your breast and breast milk prior to first use.
• Wash all parts that come into contact wrth your breast and breast milk after every use.
• If you are a mother who is infected with Hepatitis B, Hepatitis C, or Human Immunodeficiency Virus(HIV), pumping breast milk will not reduce or remove the risk of transmrtting the virus to your baby through your breast milk.
• Do not use the Bellababy breast pump while operating a moving vehicle.
• The Bellababy breast pump should not be used adjacent to or stacked with other equipment. If adjacent or stacked use is necessary, the Bellababy electric breast pump should be observed to verify normal operation in the configuration in which it will be used.

CAUTION: Can lead to minor injury:

• Do not expose the breast pump to direct sunlight.
• Separation from power is only assured through the disconnection of the power adaptor from the wall socket outlet.
• If you feel pain in your breast or nipple, turn the pump off or slide a finger between the flange and your breast to immediately break the suction.
• Contact a healthcare professional or breastfeeding specialist if you experience problems or pain.
• Portable and mobile radio frequency communications equipment can affect the Bellababy breast pump.
• Use only the power adaptor that is with no more than fN output voltage.
• Make sure the voltage of the power adaptor is compatible with the power source.
• Wash hands thoroughly with soap and water before touching breast pump, kit and breasts and avoid touching the inside of containers or lids.
• Separate and wash all parts that come in contact with breast milk immediately after use to avoid dry up of breast milk residue and prevent growth of bacteria. Always inspect breast shields, flanges, valves, membranes to use for cleanliness.
• Only use drinking-quality tap or bottled water for cleaning your breast pump and parts.
• Do not store wet or damp parts as mold may develop.
• If any part becomes moldy, discontinue use and replace it. Contact Bellababy Customer Service at service-us@bellababy-med.com.
• Do not run pump with wet parts. Doing so will harm the pump motor.
• While some discomfort may be felt when first using a breast pump, using a breast pump should not cause pain.
• If you are experiencing discomfort at the base of the nipple due to rubbing of your breast tissue with the breast shield tunnel, use of a lubricant such as Tender Care TM Lanolin may be beneficial. For assistance with correct breast shield sizing and comfort please refer to the “Silicone flange sizing” or see a lactation consultanVbreastfeeding specialist.
• Contact your healthcare professional or breastfeeding specialist if you can express only minimal or no milk or if expression is painful.
• Do not try and express with vacuum that is too high and uncomfortable(painful). The pain, along with potential breast and nipple trauma, may decrease milk output.
• Do not thaw frozen breast milk in a microwave or in a pan of boiling water.
• Do not microwave breast milk Microwaving can cause severe bums to baby’s mouth from hot spots that develop in the milk during microwaving.(Microwaving can also change the composition of breast milk)

Guidance and manufacturer’s

declaration-electromagnetic emission-for all EQUIPMENT AND SYSTEMS

1. This equipment has been tested and found to comply wrth the limrts for medical devices in IEC 60601-1-2. These limits are designed to provide reasonable protection against harmful interference in a typical medical installation.
2. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to other devices in the vicinrty. However, there is no guarantee that interference will not occur in a particular installation.
3. lf this equipment does cause harmful interference to other devices, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
   • Reorient or relocate the receiving device.
   • lncrease the separation between the equipment.
   • Connect the equipment into an outlet on a circuit different from that to which the other device(s) are connected.
   • Consult the manufacturer or field service technician for help.

Table1: Guidance and manufactures Declaration-electromagnetic emissions

The RI A8042/BLA8042-2 is intended for use in ten electromagnetic environment specified below. Ten customer or the user of The BLA8042/BLA8042-2 should assure that it is used in such an environment

its internal function. Therefore, its PF emissions are not likely to cause any interference in nearby electronic equipment.
RF emissions CLSPR 11| Class B| Ten BLA8042/BLA8042-2 is suitable for use in all Establishments, including domestic establishments and those directly connected to the public low-voltage power supply network that supplies buildings used for domestic purposes.
Harmonic emissions IEC 61000-3-2| A| –
Voltage fluctuations/Flicker emissions IEC 61000-3-3| Complies| –

Warning

• The electric breast pump should not be used adjacent to or stacked with other equipment. If adjacent or stacked use is necessary, the electric breast pump should be monitored to verify normal operation in the configuration in which it will be used.
• Do not use other accessories than those specified or sold by the manufacturer as replacement parts for internal components as it may result in increased emissions or decreased immunity of the Symphony device.

Table 2: Guidance and manufacturer’s declaration electromagnetic immunity

The BLA8042/BLA8042-2 is intended for use in the electromagnetic environment specified below. The customer or the user of the BLA8042/BLA8042-2 should assure that it is used in such an environment.

Immunity test| Test level| Compliance level| Electromagnetic environment – guidance
---|---|---|---
Electrostatic Discharge (ESD) IEC 61000-4-2| +2, 4, 6, 8 kV contact, +2, 4, 8, 15 kV air| +2, 4, 6, 8 kV contact, +2, 4, 8, 15 kV air| Floors should be wood, concrete or ceramic tile. If floors are covered with synthetic material, the relative humidity should be at least 30%.
Electrical fast transient/burst IEC 61000-4-4| +2 kV for power supply lines| +2 kV for power supply lines| Mains power quality should be that of a typical commercial or hospital environment.
Surge IEC 61000-4-5| +1 kV lines to lines| +1 kV lines to lines| Mains power quality should be that of a typical commercial or hospital environment.
Voltage dips, short interruptions and voltage variations on power supply input lines IEC 61000-4-11| <5% UT (>95% dip in UT) for 0,5 cycle 40%/UT for 5 cycle 70%/UT for 25 cycle >95% dip in UT for 5 cycle| <5% UT (>95% dip in UT) for 0,5 cycle 40%/UT for 5 cycle 70%/UT for 25 cycle >95% dip in UT for 5 cycle| Mains power quality should be that of a typical commercial or hospital environment.
Power frequency (50/60 Hz) magnetic field IEC 61000-4-8| 30A/m| 30A/m| Power frequency magnetic fields should be at levels characteristic of a typical location in a typical commercial or hospital environment.

Guidance and manufacturer’s declaration-electromagnetic immunity for ME EQUIPMENT and ME SYSTEM that are not LIFE-SUPPORTING.

Table 3: Guidance and manufacturer’s declaration – electromagnetic immunity

The BLA8042/BLA8042-2 intended for use in the electromagnetic environment specified below, The customer or the user of the BLA8042/BLA8042-2 should assure that it is used in such an environment

Immunity test| Test level| Compliance level| Electromagnetic environment – guidance
---|---|---|---
Conducted RF IEC 61000-4-6| 3 Vrms 150 kHz to 80 MHz| 3 Vrms| Portable and mobile RF communications equipment should not be used closer to any part of the BLA8042/BLA8042-2, including cables, than the recommended separation distance calculated from the equation applicable to the frequency of the transmitter.
Radiated RF IEC 61000-4-3| 3 V/m 80 MHz to 2.5 GHz| 6 V/m| Field strengths from fixed RF transmitters, as determined by an electromagnetic site survey, should be less than the compliance level in each frequency range. Interference may occur in the vicinity of equipment marked with the following symbol:

• NOTE 1 At 80 MHz and 800 MHz, the higher frequency range applies.
• NOTE 2 These guidelines may not apply in all situations. Electromagnetic propagation is affected by absorption and reflection from structures, objects and people.

Field strengths from fixed transmitters, such as base stations for radio.(cellular/cordless telephones and land mobile radios, amateur radio, AM and FM radio broadcast and TV broadcast cannot be predicted theoretically with accuracy. To assess the electromagnetic environment due to fixed RF transmitters, an electromagnetic site survey should be considered. If the measured field strength in the location in which the BLA8042/BLA8042-2 is used exceeds the applicable RF compliance level above. The Medical BLA8042/BLA8042-2 should be observed to verify normal operation. If abnormal performance is observed, additional measures may be necessary, such as reorienting or relocating the BLA8042/BLA8042-2.

Over the frequency range 1 50 kHz to 80 MHz, field strengths should be less than 3V/m.

Recommended separation distances between portable and mobile RF communications equipment and the ME EQUIPMENT and ME SYSTEM

Recommended separation distances between portable and mobile RF communications equipment and the BLA8042/BLA8042-2 The BLA8042/BLA8042-2 is intended for use in an electromagnetic environment in which radiated RF disturbances are controlled, The customer or the user of the BLA8042/BLA8042-2 can help prevent electromagnetic interference by maintaining a minimum distance between portable and mobile RF communications equipment (transmitters) and the BLA8042/BLA8042-2 as recommended below, according to the maximum output power of the communications equipment.

Rated Maximum Output Power of Transmitter (W)| Separation distance according to frequency of transmitter (m)
---|---
| 150 kHz to 80 MHz
0.01| d=1.2
0.1| d=3.8
1| d=12
10| d=38
100| d=120

?=1.5×??or?=3.5×??or?=7×??d=W1.5×P​​ord=W3.5×P​​ord=W7×P

For transmitters rated at a maximum output power not listed above, the recommended separation distanced in meters (m) can be estimated using the equation applicable tothe frequency of the transmitter, where P is the maximum output power rating of the transmitter in watts (W) according to the transmitter manufacturer.

• NOTE 1 At 80 MHz and 800 MHz, the separation distance for the higher frequency range applies.

• NOTE 2 These guidelines may not apply in all situations. Electromagnetic propagation is affected by absorption and reflection from structures, objects and people.​​

Technical specifications

Bella baby Warranty

Bellababy products include a 1 year warranty after the date of original purchase, please contact us at Service-US@bellababy-med.com with your order number and a video showing the issue if any problem arises during use or if you have any question.Bellababy is dedicated to customer satisfaction.

• Manufacturer: Ningbo Huiyoo Baby Products Co. Ltd.
• Mdress: 523# Cizhang Road, Zhangqi Industrial Area Cixi, CN 315313
• Email:
  • Service-US@Bellababy-med.com
  • Service-EU@Bellababy-med.com
  • Service-JP@Bellababy-med.com
• www.bellababy-med.com
• www.facebookcom/Bellababy.med
• www.instagram.com/bellababy.med
• www.tiktokcom/@bellababy.med

FREQUENTLY ASKED QUESTIONS

What are the special features of the Bellababy BLA8042 Wearable Breast Pump?

The special features of the Bellababy BLA8042 Wearable Breast Pump include hands-free operation, lightweight design, low noise, and wearability.

What is the price of the Bellababy BLA8042 Wearable Breast Pump?

The price of the Bellababy BLA8042 Wearable Breast Pump is $29.99.

What are the product dimensions of the Bellababy BLA8042 Wearable Breast Pump?

The product dimensions of the Bellababy BLA8042 Wearable Breast Pump are 6.69 x 5.91 x 3.94 inches.

How much does the Bellababy BLA8042 Wearable Breast Pump weigh?

The Bellababy BLA8042 Wearable Breast Pump weighs 1.1 pounds.

Where is the Bellababy BLA8042 Wearable Breast Pump manufactured?

The Bellababy BLA8042 Wearable Breast Pump is manufactured in China.

Does the Bellababy BLA8042 Wearable Breast Pump come with a warranty?

Yes, the Bellababy BLA8042 Wearable Breast Pump comes with a 1-year warranty.

How do I utilize the hands-free feature of the Bellababy BLA8042 Wearable Breast Pump effectively?

To utilize the hands-free feature, securely attach the breast pump to your clothing using the provided attachments or accessories. Adjust the straps or clips as needed for a comfortable and secure fit, allowing you to move freely while pumping.

Why is my Bellababy BLA8042 Wearable Breast Pump not turning on?

Ensure that the pump is fully charged or has fresh batteries inserted. Check if the power button is pressed correctly. If the pump still doesn't turn on, there may be an issue with the power source or internal components.

What should I do if my Bellababy BLA8042 Wearable Breast Pump is not producing suction?

Check if all parts are assembled correctly and securely. Ensure that the pump is positioned properly on the breast and that there are no leaks in the tubing or connections. If suction is still not generated, there may be an issue with the motor or suction mechanism.

My Bellababy BLA8042 Wearable Breast Pump is making unusual noises during operation. What could be the problem?

Unplug the pump and inspect it for any loose parts or foreign objects. Check if all parts are properly aligned and connected. If the noise persists, there may be an issue with the motor or internal components.

Why is my Bellababy BLA8042 Wearable Breast Pump not charging properly?

Ensure that the charging cable is securely connected to both the pump and the power source. Check for any damage to the charging cable or port. If the pump still doesn't charge, there may be an issue with the battery or charging circuit.

What should I do if the suction strength of my Bellababy BLA8042 Wearable Breast Pump is insufficient?

Check if all parts are clean and properly assembled. Adjust the suction level if possible. If suction strength remains weak, there may be an issue with the pump's motor or suction mechanism.

How do I clean and maintain my Bellababy BLA8042 Wearable Breast Pump?

Disassemble the pump and wash all parts that come in contact with milk with warm, soapy water. Rinse thoroughly and allow to air dry. Sterilize the parts according to the manufacturer's instructions. Avoid submerging the motor unit in water.

Why is the battery life of my Bellababy BLA8042 Wearable Breast Pump shorter than expected?

Ensure that the pump is fully charged before each use and that it's not being overused. If the battery life remains short, there may be an issue with the battery or power management system.

What should I do if my Bellababy BLA8042 Wearable Breast Pump is leaking?

Check if all parts are assembled correctly and securely. Inspect for any cracks or damage in the silicone parts. If the pump continues to leak, there may be an issue with the seal or valve.

DOWNLOAD THE PDF LINK:Bellababy BLA8042 Wearable Breast Pump User Manual

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>