IntesisHome IHWFIFGL001R000 Universal IR Air Conditioner to AC Cloud Control Interface Installation Guide
- October 30, 2023
- IntesisHome
Table of Contents
IntesisHome IHWFIFGL001R000 Universal IR Air Conditioner to AC Cloud
Control Interface
Product Information
The IntesisHome device is a device that allows you to control your air conditioning system remotely. It comes with a lid, LED indicator, push button, AC connector, and DIP-Switch. The device can be connected to a Wi-Fi access point or router, RWB connector,and a remote controller (RC). The device has four switches that allow you to configure its performance and Wi-Fi range.
Product Usage Instructions
Safety Instructions
Please follow the safety and installation instructions carefully to avoid causing harm to your health and damaging the device or AC indoor unit.
Device Connection
Connect the IntesisHome device to your Wi-Fi access point or router, RWB connector, and remote controller (RC) as shown in the figure provided in the manual.
Switch Configuration
Please make sure that switches 1, 2, 3, and 4 are placed in the right position as per your desired settings. The switch configuration determines the performance and Wi-Fi range of the device. Switch 3 determines the performance of the device while switch 4 determines the Wi-Fi range of the device. Please note that changing switch 4 may affect the device’s Wi-Fi communication and cause it not to reach the current access point or Wi-Fi network to which it is connected. In case no external supply is used, decrease the device consumption by using switches 3 and 4.
Ambient Temperature
In order to obtain the ambient temperature, please set the AC unit to provide it as per the instructions provided in the manual.
Intesis Software SLU
© 2019 Intesis Software SLU All rights reserved.
This document has been carefully written by Intesis Software SLU and a lot of
effort has been made to ensure no errors or mistakes are present in the
document. Intesis Software SLU is not responsible for printing or clerical
errors.
Information in this document is subject to change without notice. No part of
this publication may be reproduced, stored in a retrieval system or
transmitted in any form or any means electronic or mechanical, including
photocopying and recording for any purpose other than the purchaser’s personal
use without the written permission of Intesis Software SLU
Intesis Software SLU
Milà i Fontanals, 1 bis
08700 Igualada
Spain
IntesisHome® is a trademark of Intesis Software SLU. Third party product names
or company names used in this document may be trademarks of their respective
companies. Its use in this document is purely for information purposes only.
Safety instructions
WARNING
Follow carefully this safety and installation instructions. Improper work may lead to serious harmful for your health and may damage seriously the interface and/or the AC indoor unit.
- This interface must be installed by accredited technical personnel (electrician, installer or authorized technical personnel) and following all the safety instructions.
- This interface must only be installed in a restricted access location.
- Before manipulating the AC indoor unit be sure it is completely disconnected from Mains power.
- In case of installation of the interface inside the AC indoor unit, fix the interface and communication cables preferably to any appropriate point of the plastic cover of the unit taking care of no blocking free movement of mobile parts and as far as possible from tubes containing liquids and power cables.
Device information
- A. Lid
- B. LED indicator
- C. Push button
- D. AC connector
- E. DIP-Switch
Device connection
- Unplug the Air Conditioner (AC) unit from mains.
- Access to the main Printed Circuit Board.
- Locate the RWB socket connector.
- Select a location for the device.
- Connect the IntesisHome device to the Air Conditioner.
- Close the Air Conditioner unit.
- Plug the AC to the power supply line.
- IntesisHome device
- Wi-Fi Access Point or Router
- RWB connector
- Remote Controller (RC)
Switch configuration
Please, make sure that switches are placed in the right position as per your desired settings.
| Switches 1 2 3 4 | Description |
|---|---|
| 0 X X X | Slave – A Fujitsu Controller must be present in BWR bus, configured |
as Master (Default value)
1 X X X| Master – Fujitsu Controller not needed in BWR bus. If it exists, it
must be configured as Slave
X 0 X X| Machine type: RAC inverter model G series, VRF J-II, VRF V-II or VRF
VR-II 10 (Default value)
X 1 X X| Machine type: RAC inverter, RAC non-inverter, VRF V, VRF S or VRF J
X X 0 X| Low Power Mode
X X 1 X| High Performance Mode (Default value)
X X X 0| WIFI power is limited
X X X 1| Max WIFI power (Default value)
Switch 3
This switch determines the performance of the device. Running in High
Performance Mode means maximum consumption and maximum device performance.
Switch 4
This switch determines the Wi-Fi range of the device. Maximum range is set by
default. Consider that changing this switch may affect to device Wi-Fi
communication, happening a device in a running installation not to reach the
current access point or Wi-Fi network to which is connected.
In case no external supply is used: In very specific installations, AC port
consumption may be overpassed, leading the device to reboot. If that happened,
decrease device consumption by using SW3 and SW4.
NOTE: Remember that you need to power cycle the climate system or the
IntesisHome device for the changes in the switches to be applied.
Ambient Temperature
In order to obtain the ambient temperature please set the AC unit to provide it as follows.
- Connect the Intesis Home device to the AC unit with a Standard Remote Controller present and the room sensor on the Remote Controller activated.
- Detailed information on how to set up this in the Remote Controller can be found in the following extract from the Fujitsu remote controller manual.
© Intesis Software SLU – All rights reserved This information is subject to
change without notice
IntesisHome® is a registered trademark of Intesis Software SLU
http://www.intesishome.com
info@intesishome.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>