RugGear PTM01G Rugged Tablet User Guide

: June 6, 2024
: RugGear

RugGear PTM01G Rugged Tablet

SIM/Micro SD

KEYS AND SPECIAL FEATURES

505 KEY: Press and hold to select an emergency number stored by you. This function can only be used with an optionally available LWP app
POWER INDICATOR, PLEASE SEE THE DETAILED DEFINITION IN 8.5
FRONT CAMER
MIC/BAROMETRIC SENSO
FUNCTION/CUSTOMIZED KEYS: F1/F2/F3, programmable keys used by different apps.
BACK KEY/HOME KEY/RECENT APPLICATION.
VOLUME KEY: Volume upNolume down.
POWER KEY: Press and hold to power the device ON/OFF. Press briefly to power. ON/OFF the standby mode
LOUDSPEAKER
4 POGOS PINS CONNECT THE DOCKING STATION FOR TABLET CHARGING
(SIM CARD/MICRO SD SLOT: Supports Nano SIM card or microSD card.
3.SMM AUDIO JAC
TYPE A; Connects the Type-A OTG device; charging is not supported
TYPE C: To charge and connect the de'(jce with the included USB cable, and also connect the Type C OTG device
BATTERY STATUS INDICATOR LED1: GJ1 Indicates the level of battery #1; please see the details in 8.5
REAR CAMERA
BATTERY STATUS INDICATOR LED2: g2 Indicates the level of battery #2; please see the details in 8.5
FLASH: Optional when taking pictures/Videos or works as a flashlight.
BATTERY 1: removable battery
BATTERY 2: removable battery
BATTERY COVER LOCK: Use to unlock/lock the battery cover
6 SCREW HOLES: Use to fasten the VESA standard mounting bracket or band strap.

INTRODUCTION

This document contains information and safety regulations that must be observed for the safe operation of device RG935 under the described onditions. Nonobservance of information and instructions can have serious consequences and may violate regulations. Please read the manual and these safety instructions before using the device. In the case of any doubt, the English version takes precedent. The current EU declaration of conformity, certificates, safety instructions and manuals can be found at www.RugGear.com or can be requested from Power Idea Technology (Shenzhen) Co., Ltd.

RESERVED

The content of this document is presented as it currently exists. Power Idea Technology (Shenzhen) Co., Ltd. does not provide any explicit or tacit guarantee for the accuracy or completeness of the content of this document, including, but not restricted to, the tacit guarantee of market suitability or fitness for a specific purpose unless applicable laws or court decisions make liability mandatory.
Power Idea Technology {Shenzhen) Co., Ltd. reserves the right to make changes to this document or to withdraw it any time without prior notice. Changes, errors and misprints may not be used as a basis for any claim for damages. All rights reserved.
Power Idea Technology {Shenzhen) Co., Ltd. cannot be held responsible for any data or other loss and direct or indirect damages caused by any improper use of this device.

EU DECLARATION OF CONFORMITY

The EU declaration of conformity can be found at the end of this manual.

SAFETY ADVICE

Do not touch the screen of the device with sharp objects. Dust particles and fingernails can scratch the screen. Keep the screen clean. Gently remove dust from the screen with a soft cloth and do not scratch the screen.
Do not leave the device in environments with excessive temperatures, as this could lead to the battery overheating, resulting in fire or explosion.
Do not charge the device near any flammable or explosive substances.
Only charge the device in dry indoor conditions,
Do not charge the device in dusty or humid environments.
Do not use the device in any areas where use is prohibited by regulations or legislation.
Do not expose the device or charger to strong magnetic fields, such as those emitted from induction ovens or microwaves.
Do not attempt to open or repair the device.
Incorrect repair or opening can lead to the destruction of the device, fire or explosion.
Only authorized personnel are permitted to repair the device.
Only use accessories approved by Power Idea Technology (Shenzhen) Co., Ltd.
Power off the device in hospitals or other places where the use of mobile phones is prohibited.
This device may adversely affect medical equipment, such as pacemakers.
Always keep a distance of at least 15 cm between the device and such equipment.
Make sure the volume level is not set at an excessive level when connecting earphones and headphones to protect your hearing.
Observe all corresponding laws that are in force in the respective countries regarding the use of devices while operating a vehicle.
Power off the device and disconnect the charging cable before cleaning the device.
Do not use any chemical cleaning agents to clean the device or the charger.
Use a damp and anti-static soft cloth for cleaning.
The adapter must be installed near the equipment and be easily accessible.
The device must only be connected to a USB interface, version USB 2.0.
Do not discard old and abandoned lithium batteries into household waste, take them to a designated waste disposal point.
The user is solely liable for any and all damages and liabilities caused by malware downloaded when using the network or other data-exchange functions of the device. Power Idea Technology (Shenzhen) Co., Ltd. cannot be held responsible for any such claims.

WARNING
Power Idea Technology (Shenzhen) Co., Ltd. will not assume any liability for damage caused by disregarding any of this advice or by any inappropriate use of the device.

BATTERY

There is a risk of explosion if the battery is replaced by an incorrect type. Dispose of used batteries according to the instructions.

PREPARATION

INSTALL THE BATTERY

With the back of the tablet facing up, as shown in Figure 1, open the upper and lower locks of the battery cover up or down respectively.
Then slide the battery cover slider lock outwards, and when it reaches the final position, use the other hand to buckle the battery cover from the side of the battery cover.
Remove the battery cover and put the battery in the battery compartment.
Remove the battery cover and put the battery in the battery compartment.
After the battery cover is installed, press the edge of the battery cover with your hand to fasten the upper and lower buckle locks.

Tips:

When the battery cover is not fully pressed into place, the upper and lower buckle locks cannot be locked.
When the upper and lower buckle locks of the battery cover are not fully opened, install the battery cover. The battery cover will not be pressed tightly.

Note:
Please ensure that the rubber cover of the device’s earphone and USB connector are perfectly sealed to make the waterproof and dustproof function work well. No special declaration will be made later on.

INSTALLATION OF THE NANO SIM CARD

The device has two slots for nano SIM cards.
Use the ejector pin to access the SIM card slot until the SIM card tray is ejected.

INSTALLATION OF THE MICROSD CARD

The device supports a microSD card (up to 256 GB). It is located in the SIM card tray. SIM slot 2 can support either a microSD card or an additional SIM card. Example: one SIM card and microSD, or two SIM cards and no microSD.

WARNING
Please insert or remove the microSD card when the device is switched off.

Note:
Make sure that the rubber cover on the earphone and USB connector of the device are fully sealed to ensure complete waterproofing and dustproofing. No special declaration will be made in the future.

CHARGING

The RG935 supports 9V/2A charging, Only use valid RugGear licensed chargers and cables because unlicensed products may cause the battery to explode or damage the device. The device must only be charged in an ambient temperature range of +0°C to +45°C. The normal operating temperature of this mobile phone is -10°Cto 50°C.

INTRODUCTION TO FUNCTIONS

Function/customized keys (F1/F2/F3)

Function keys (F1/F2/F3) are customized keys, you can choose and modify the features that you want to. When using one for the first time, it must be set it in your app (Custom Key). The F1 key can be used as a PTT key. Select PTT in the menu list, then press and hold the F1 key to enable software talkback .

Multifunctional Alarm (LWP)

The multifunctional alarm is the feature that detects the status of the mobile phone status during motion and rest and automatically notifies the emergency contact via phone call/SMS.

Default password: 1122.
After opening the application for the first time, a default phone number is requireed to be set for the alarm.
If the mobile phone uses two SIM cards, a default phone number is required to be set for calling/SMS.

Take a screenshot

Press the “power key “and “volume-” at the same time to take a screenshot.

Battery icon on the screen

When two batteries are used at the same time, the battery icon on the screen represents the total capacity percentage of battery 1 + battery 2. When a single battery is used, the battery icon indicates the percentage of this single battery’s capacity.

Indicator light description

LED indicator light (Front)	LED Status	Indication
The red light is always on.	Charging
The green light is always on.	Fully charged 100%
Red light flashes continuously.	Low battery< 15%, tablet needs to be

recharged, or just replace the battery.
Battery status indicator (Rear)| The orange light is always on.| Low battery < 30%, tablet needs to be recharged or just replace the battery.
The red light is always on.| Low battery < 15%, battery hot switch is about to disable.

I/O Interface notice (Type C & Type A)

Type A (USB 2.0): Connect the Type A OTG device. Charging is not supported.
Type C (USB 3.1 Gen): To charge and to connect the device with theincluded USB cable; to connect the Type C OTG device and support DP video output and Type C one-line extra display.
When Type C is used alone, it supports the USB 3.1 Gen speed rate.
If an 1/0 interface (Type C or Type A) is already connected to an OTG device, and the other interface is connected to an OTG device, the device connected first has a risk of reconnection.
When a Type C or Type A interface is connected to OTG device, the tablet can only be the master device (connected to OTG device), and the slave device mode (such as U drive mode) is not supported.
When a Type C and Type A interface are used at the same time, Type C does not support the USB3.1Gen speed rate and automatically changes to the USB2.0 speed rate.
Operation of all USS-compatible peripherals not guaranteed.

RECYCLING

The crossed-out wheelie-bin symbol on the product, battery, literature, or packaging is a reminder that all electrical and electronic products, batteries, and accumulators must be taken to separate collection points at the end of their working life. This requirement applies in the European Union. Do not dispose of these products as unsorted municipal waste. Always return used electronic products, batteries, and packaging materials to dedicated collection points. This helps prevent uncontrolled waste disposal and promotes the recycling of materials. More detailed information is available from the product retailer, local – waste authorities, national producer responsibility organisations, or your local Power Idea Technology (Shenzhen) Co., Ltd. representative.

INFORMATION CONCERNING CE SAR CERTIFICATION (SPECIFIC ABSORBATION RATE)

The SAR limit of Europe is 2.0W/kg for the head and Body, 4.0W/kg for the limbs. The device has been tested against this SAR limit. The highest SARvalue reported under this standard during product certification for use at the ear is 0.64W/kg and when correctly worn on the body is 1.29W/kg ,limbs is 1.35W/kg. This device was tested for typical body worn operations with the back of the handset kept 5mm from the body. The device complies with RF specifications when used at 5mm from the body. Belt clips, holsters and similar accessories used should not contain metallic components in the assembly. The use of accessories that do not satisfy these requirements may not comply with RF exposure requirements,and should be avoided.

TRADEMARKS

All other trademarks and copyrights are the properties of their respective owners.

WARRANTY

European customers, please check: https://ruggear.com/warranty-terms/
Customers in the Americas, please check: https://ruggear.com/terms-and-conditions-americas/

FCC Statement

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference.
(2) This device must accept any interference received, including interference that may cause undesired operation.
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

NOTE:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radionv technician for help.

SAR Information Statement

Your tablet PTM01Gis a radio transmitter and receiver. It is designed and manufactured not to exceed the emission limits for exposure to radiofrequency (RF) energy set by the Federal Communications Commission of the U.S. Government. These limits are part of comprehensive guidelines and establish permitted levels of RF energy for the general population. The guidelines are based on standards that were developed by independent scientific organizations through periodic and through evaluation of scientific studies. The standards include a substantial safety margin designed to assure the safety of all persons, regardless of age and health. The exposure standard for Tablets employs a unit of measurement known as the Specific Absorption Rate, or SAR. The SAR limit set by the FCC is 1.6 W/kg. Tests for SAR are conducted with the tablet PTM01 G transmitting at its highest certified power level in all tested frequency bands. Although the SAR is determined at the highest certified power level, the actual SAR level of the phone while operating can be well below the maximum value. This is because the Tablet is designed to operate at multiple power levels so as to use only the power required to reach the network. In general, the closer you are to a wireless base station antenna, the lower the power output Before a phone model is available for sale to the public, it must be tested and certified to the FCC that it does not exceed the limit established by the government adopted requirement for safe exposure. The tests are performed in positions and locations (e.g., at the ear and worn on the body) as required by the FCC for each model. The highest SAR value for this mcx:lel Tablet when tested for use 0.95 W/Kg (1g) for Body- worn; 1.06 W/Kg (1g)for Hotspot. While there may be differences between the SAR levels of tablet and at various positions, they all meet the government requirement for safe exposure. The FCC has granted an Equipment Authorization for this model Tablet with all reported SAR levels evaluated as in compliance with the FCC RF exposure guidelines. SAR information on this roodel Tablet is on file with the FCC and can be found under the Display Grant section of http://www.fcc.gov/ oet/fccid after searching on FCC ID: ZLE-RG935 Additional information on Specific Absorption Rates (SAR) can be found on the Cellular Telecommunications Industry Asso-ciation (CTIA) web-site at http://www.wow-com.com. In the United States and Canada, the SAR limit for Tablets used by the public is 1.6 watts/kg (W/kg) averaged over one gram of tissue. The standard incorporates a sub-stantial margin of safety to give additional protection for the public and to account for any variations in measurements.

IC STATEMENT

This device complies with Industry Canada licence-exempt RSS standard(s) Operation is subject to the following two conditions:

(1) This device may not cause interference, and
(2) This device must accept any interference, including interference that may cause undesired operation of the device.
This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. End user must follow the specific operating instructions for satisfying RF exposure compliance. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
These requirements set a SAR limit of 1.6 W/kg averaged over one gram of tissue.
The highest SAR value for this model phone when tested for use 1.06 W/Kg (1g) for Hotspot and when worn on the body is 0.95W/Kg. 5150-5250 MHz indoor use only.