cudy LT500 4G LTE AC1200 Dual Band Wi-Fi Router Installation Guide
- June 6, 2024
- cudy
Table of Contents
Quick Installation Guide
Email:support@cudy.com
**Website:www.cudy.com**
Package Content
1 x 4G LTE Router
1 x Power Adapter
1 x Quick Installation Guide
1 x Ethernet Cable
1 x SIM Adapter
Quick Installation
-
Insert the Micro SIM card into the slot until you hear a click.
-
Connect the power adapter and turn on the router. Waiting for 2 minutes for it to start.
-
Check the status of the system LED.
If the system LED turns to solid blue, means connecting to 4G network successfully.
If the system LED turns to solid purple, means connect to 2/3G network.
If the system LED turns to solid red, please follow the instructions of Customize the 4G Router.
Customize The 4G Router
-
Connect the router via ethernet cable or Wi-Fi. The network name and password is printed on the bottom of the router.
-
Launch a web browser and enter http://cudy.net/ (or http://192.168.10.1/) in the address bar, use admin as a password to log in.
-
The below page would pop up if your SIM card needs a PIN to unlock. Please enter your PIN and click Save & Apply, then wait 15 seconds to connect to the Internet.
-
Then please check 4G information card of the status page. If the status is connected, means connected to the internet successfully.
-
If 4G is not connected, or if you want to customize the router yourself, click “Quick Setup” and follow the step-by-step instructions to configure the router.
Note:
- If you are not sure about APN parameters, please contact your internet provider.
- If you meet any other problems, don’t hesitate to contact our technical support team: support@cudy.com
Enjoy the internet!
LED and Button
| Name | Status | I indication |
|---|
System
LED|
Solid On
| Red| Internet is not connected
Blue| 4G or WAN Internet is connected
Purple| 2/3G is Connected
Flashing
| Red| The system is starting up
Blue| WPS is in progress
Red-Purple-Blue| Software Upgrading
Off| The power adapter is not connected to the device.
Ethernet
LED| On| The corresponding Ethernet port is connected.
Off| The corresponding Ethernet port is not connected.
Button| WPS| Press and hold 1 second to enable the WPS function.
Reset| Press and hold this button for about 6 seconds to reset the router to
its factory default settings.
Need Help?
Q1. What should I do if I cannot access the web management page?
Al: If the computer is set to a static IP address, change its settings to
obtain an IP address automatically.
A2: Make sure http://cudy.net/or http://192.168.10.1/ is correctly entered
in the web browser.
A3: Use another web browser and try again. A4: Reboot your router and try
again.
AS: Disable and enable the active network adapter in use.
Q2. How do I restore the router to its factory default settings?
Al: With the router powered on, press and hold the RESET button for 6 seconds
before release. Wait the router resets.
A2: Log in to the web management page of the router, and go to Advanced
Settings >Reset, click Perform Reset and wait until the reset process is
complete.
FCC Statement
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Caution: Any changes or modifications to this device not explicitly approved by
the manufacturer could void your authority to operate this equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
RF Exposure Information
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
a minimum distance 20cm between the radiator and your body.
Model: LT500www.cudy.com
Support@cudy.com
Company: Shenzhen
Cudy Technology Co., Ltd
Documents / Resources
| cudy
LT500 4G LTE AC1200 Dual Band Wi-Fi
Router
[pdf] Installation Guide
LT01, 2APRGLT01, LT500 4G LTE AC1200 Dual Band Wi-Fi Router, 4G LTE AC1200
Dual Band Wi-Fi Router
---|---
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>