TAOTRONICS TT-TF012 Wall Fan User Manual
- June 6, 2024
- TaoTronics
Table of Contents
TAOTRONICS
WALL FAN
User Manual
THANK YOU
FOR BEING OUR CUSTOMER
Your purchase is truly appreciated!
We hope you are over-the-moon with our product!
IMPORTANT SAFETY INSTRUCTIONS
Summon A Cool Breeze Into Your Space
BEFORE USING THIS APPLIANCE READ ALL INSTRUCTIONS AND CAUTIONARY MARKINGS IN YOUR USER MANUAL AND ON THE APPLIANCE.
| DO NOT touch or hold the mains plug with wet hands.
---|---
| DO NOT block or cover air flow to or from the fan while in operation.
| DO NOT insert fingers or objects through the grille while in operation.
INTENDED USE
- This appliance is not intended for use by people (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning the use of the appliance by person responsible for their safety.
- Close supervision is necessary when any appliance is used by or near children. Children should be supervised to ensure that they do not play with the appliance. Cleaning and user maintenance shall not be done by children unless they are older than 8 and supervised.
- Use the appliance only for intended household purposes as described in this User Manual. Any other use is not recommended that may cause fire, electric shock, or injury to people.
ELECTRICITY SAFETY
- This appliance must be provided with correct voltage via a professionally installed power socket. Make sure the voltage indicated on the label of the appliance is the same as your local supply.
- IMPORTANT – This appliance has a polarized plug (one blade is wider than the other). To reduce the risk of electric shock, this plug is intended to fit in a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician. Do not attempt to rig this safety feature.
- This product employs overload protection (fuse). A blown fuse indicates an overload or short-circuit situation. If the fuse blows, unplug the product from the outlet. Replace the fuse as per the user servicing instructions (follow product marking for proper fuse rating) and check the product. If the replacement fuse blows, a short-circuit may be present and the product should be discarded or returned to an authorized service facility for examination and/or repair.
- WARNING: To Reduce The Risk Of Fire Or Electric Shock, Do Not Use This Fan With Any Solid-State Speed Control Device.
- Include instructions pertaining to a risk of fire, electric shock, or injury to persons, for cleaning and user-maintenance, such as lubrication.
- DO NOT operate any fan with a damaged cord or plug. Discard fan or return to an authorized service facility for examination and/or repair.
- DO NOT run cord under carpeting. Do not cover cord with throw rugs, runners, or similar coverings.
- DO NOT route cord under furniture or appliances. Arrange cord away from traffic area and where it will not be tripped over.
- Disconnect the appliance from the power supply before servicing.
FOR HOUSEHOLD USE ONLY
READ AND SAVE THESE INSTRUCTIONS
| Have your wall fan checked regularly for any sign of malfunction!
---|---
Check if
• Plug, cord, or appliance is damaged.
• Excessive noise, unpleasant odor, or abnormal heat. Stop using, check FAQ
and contact TaoTronics Support Team.
Specifications
| Model | TT-TFO12 |
|---|---|
| Input | 120V~ 60Hz |
| Rated power | 55W |
ASSEMBLING YOUR FAN
Summon A Cool Breeze Into Your Space
Assemble Your Fan
1 Unscrew the rear grille nut counterclockwise.
2
- Position the rear grille onto the fan head and turn the grille nut clockwise to secure the rear grille. (Note: The three alignment holes must be aligned with the three prongs.)
- Insert the blade through the shaft and secure the blade with the blade cap. (Note: Make sure the retaining pin on shaft fits into the groove on blade.)
|
---|---
- Open up all locking clips.
- Align front and rear grilles, then snap the front grille into place as the illustration shows.
- Put all clips back to clamp tightly.
Mount Your Fan
- Measure the distance between two holes in wall bracket, drill two identical holes in wall with a proper ! drill bit as the illustration shows. !
- Push the screw anchors separately into the holes, then fix the wall bracket in position with the screws.
- Slide metal sheet into the wall bracket to hold the fan in place.
USING YOUR FAN
Control Panel
Turn OFF
Pull the right rope until the indicating mark points to “OFF”.
Fan Speed
Pull the right rope repeatedly to adjust 3-level speed LOW-MED-HI.
Oscillation
Pull the left rope to start/stop oscillating.
User Servicing Instructions
This wall fan features a fused safety plug which is designed to cut off electric current to the fan if an electrical fault occurs. If your fan loses power and you suspect that the fuse on your fan has blown,
- Grasp plug and remove from the receptacle or other outlet device. DO NOT unplug by pulling on cord.
- Open fuse cover. Slide open fuse access cover on top of attachment plug towards blades.
- Remove fuse carefully. Insert the tip of your tool into fuse slot (close with the terminal), then prize the fuse gradually and slowly, but not overexert. If you feel tight, you can try it at several times and prize the fuse little by little. When one side of the fuse has been prized, then you can get the fuse out entirely. Risk of fire. Replace fuse only with 2.5 Amp, 125 Volt fuse.
- Close fuse cover. Slide closed the fuse access cover on top of attachment plug. Risk of fire. DO NOT replace attachment plug. Contains a safety device (fuse) that should not be removed. Discard product if the attachment plug is damaged
CLEANING AND MAINTENANCE
Always take the fan off wall before cleaning for safety reasons.
A soft cloth is recommended for cleaning the blade.
To remove dust between the grilles, a pipe cleaner, flexible dust wand, vacuum
cleaner or compressed air are acceptable.
- Always make sure the wall fan is turned off and unplugged before cleaning.
- DO NOT stick any foreign objects or your fingers inside of the unit.
- Never immerse in water or allow water to drip into the motor housing.
- DO NOT clean with abrasive chemicals or flammable
TROUBLESHOOTING
| Q | A |
|---|---|
| Excessive noise. | • It is normal that there is noise during operation. |
If too loud, please set the fan to lower speed.
• Check if the blade is installed properly.
Fan does not operate.| • Make sure the fan is connected to a powered
electrical outlet.
Oscillation is not steady or fan vibrates.| • Make sure the fan is
mounted firmly on a vertical wall.
• Clean the blade regularly.
The troubleshooting guide addresses the most common problems. If problems
persist, feel free to contact our Customer Support at
[email protected]
WARRANTY AND SERVICE
Thanks for choosing TaoTronics wall fan. This product is covered with TaoTronics product and labor warranty for 12 months from the date of its original purchase.
The warranty will not apply in cases of:
- Accident, misuse, or repairs performed by unauthorized personnel.
- Any unit that has been tampered with or used for commercial purpose.
- Normal wear and tear of wearable parts.
- Use of force, damage caused by external influences.
- Damage caused by non-observance of the User Manual, e.g. connection to an unsuitable mains supply or non- .compliance with the instructions.
- Partially or completely dismantled appliances.
- Defects caused by or resulting from damages from shipping or from repairs, service, or alteration to the product or * any of its parts that have been performed by a repair person not authorized by TaoTronics.
We can only provide after sales service for products that are sold by TaoTronics or TaoTronics authorized retailers and distributors. If you have purchased your unit from a different place, please contact your seller for return and warranty issues.
* Please have your invoice and order ID ready before contacting Customer Support.
[email protected]
www.taotronics.com
Manufacturer: Shenzhen NearbyExpress Technology Development Co.,Ltd. Address:
Floor 7, Building E, Galaxy World Phase II, Shenzhen, China
Made in China
TT-TF012