TAURUS ATLAS 2400 CERAMIC Steam Iron Instruction Manual

: June 9, 2024
: taurus

TAURUS ATLAS 2400 CERAMIC Steam Iron

ATLAS 2400 CERAMIC Steam Iron

DESCRIPTION

A Spray button
B Steam blast button
C Steam flow control
D Auto-cleaning button
E Temperature regulator
F Pilot light
G Filling spout
H Spray nozzle
I Soleplate

Read these instructions carefully before switching on the appliance and keep them for future reference. Failure to follow and observe these instructions may result in an accident.

USE AND CARE:

Fully unroll the appliance’s power cable before each use.
Do not use the appliance if the accessories attached to it are defective. Replace them immediately.
Do not use the appliance on any part of the body of a person or animal.
Do not use the appliance with pets or animals.
Do not use the appliance to dry textiles of any kind.
Turn the thermostat control to the minimum (MIN) setting. This does not mean that the iron is switched off permanently

INSTRUCTIONS FOR USE

BEFORE USE:

Remove the appliance’s protective film.
Some parts of the appliance have been lightly greased. Consequently, the first time the appliance is used a light smoke may be detected
Prepare the appliance according to the function you wish to use.

FILLING WITH WATER:

It is essential to have filled the deposit with water to be able to work with steam.
Open the lid of the filling mouth.
Fill the deposit taking care to observe the MAX level (Fig. 1)
Close the lid of the filling mouth.

USE:

Unroll the cable completely before plugging it in.
Connect the appliance to the mains.
The pilot light (F) comes on.
Turn the thermostat control to the desired temperature position.
Do not use temperatures higher than those indicated on the garments to be treated.
● Temperature for synthetic fibres (Polyester, Nylon…).
●● Temperature for silk, wool.
●●● Temperature for cotton. (Minimum temperature for steam ironing)
Max Temperature for linen.

– If garment has various kinds of fibres, select the temperature for the fibre that requires the lowest temperature. (For example, select the temperature for polyester for an article made out of 60% polyester and 40% cotton).
– Wait until the pilot light (F) has gone out which will indicate that the appliance has reached an adequate temperature.
– During use the pilot light (F) will automatically flash on and off, thus indicating that the heating elements are operating in order to maintain the desired temperature

DRY IRONING:

The appliance has a steam flow regulator (C) that permits dry ironing (without steam) when placed in the 0 position.

STEAM IRONING:

It is possible to iron with steam whenever the deposit is filled with water and the adequate temperature is selected.

STEAM FLOW CONTROL:

The appliance has a (C) control knob that allows to get the control of the steam flow.

SPRAY:

The spray can be used in both steam and dry ironing.
Press the spray button ( A ) to use this operation.
The spray button has to be pressed repeatedly to release the first spray.

STEAM BLAST:

This function proportions extra steam for eliminating wrinkles.
Press the steam blast button (B). Wait a few seconds until vapour penetrates the fibres of the garment before pushing the button again. For optimum steam quality, do not apply more than three successive blasts.
The spray button has to be pressed repeatedly to release the first spray.

VERTICAL STEAMING

It is possible to iron hanging curtains, items of clothing on his hanger, etc. To do so, follow the instructions:
Select the maximum temperature of the iron, while turning the temperature regulator of theironzin a clockwise direction (Fig 2).
Move the iron in a top to bottom direction while pressing the steam control ( B ). Important: for cotton and linen, its recommended to put the iron base in contact with the material. For other more delicated fibres, it’s recommended to keep the iron base at some centimetres of distance.

ONCE YOU HAVE FINISHED USING THE APPLIANCE:

Select the minimum position (MIN) using the thermostat control.
Unplug the appliance to the mains.
Remove the water from the water tank.
Clean the appliance

CLEANING

Disconnect the appliance from the mains and let it cool before undertaking any cleaning task.
Clean the equipment with a damp cloth with a few drops of washing-up liquid and then dry.
Do not use solvents, or products with an acid or base pH such as bleach, or abrasive products, for cleaning the appliance.
Do not submerge the appliance in water or any other liquid, or place it under a running tap.

SELF-CLEANING FUNCTION:

It is important to self-clean the appliance at least once a month to remove calcium and any other built-up minerals inside the iron.
Fill the depository to its maximum level, as indicated on “water fill” section.
Place the iron in a vertical position, plug in to the mains and select the maximum temperature.
Leave the appliance to heat up until the pilot light indicates that it has reached its consigned temperature.
Unplug the appliance and place in the sink.
Press the self-clean button (D), and keep it pressed down.
Let the water flow out through the steam vents in the base, while lightly shaking the appliance.
Release the button after a minute or when the tank becomes empty.
Leave the iron in the vertical position until it has cooled.

HOW TO DEAL WITH LIME SCALE INCRUSTATIONS:

For the appliance to work correctly it should be kept free of lime scale or magnesium incrustations caused by the use of hard water.
To prevent this kind of problem, we recommend the use of water with low lime or magnesium mineralization.
Homemade solutions are not recommended for de-scaling this appliance, such as the use of vinegar.

Downloaded by: pm-capetown on 19-09-2022 12:41 CEST

United Arab Emirates P.O.BOX 8543, Dubai 14506246200