SCHUNK JR4 Valve Adapter Owner’s Manual

SCHUNK JR4 Valve Adapter

Charging Your Phone or Tablet Using Charging Cables

Working Status| Wireless Charging

Indicator

| Battery Level

Indicator

---|---|---
Charging / Fully charged| Off| Solid white

Charging the iPhone 12 Series and Other Devices Wirelessly

Charge the iPhone 12 Series

1.  To activate the wireless charging function, press the power button. The wireless charging indicator will breathe blue.
2.  Place your iPhone 12 on the charger as illustrated below and it will be held in place magnetically. The wireless charging indicator will turn solid blue, indicating it is charging your phone.

Charge Other Devices
For other phones that support wireless charging, align your smartphone with the charging logo on the charger. If no charging icon shows on your device, try adjusting the position of your phone.

Note: You cannot charge your device wirelessly in these scenarios:

•  When using a case with a pop socket
•  When using an ultra-thick (> 5 mm) protective phone
•  Do not use an adapter with an output of 5V/1A (5W) or less.
•  Wireless chargers make charging more convenient than wired chargers, but confined by current wireless technology, their charging speed is slower than that of wired chargers.
• High temperatures will reduce charging speed and restrict power, which is something that happens to all wireless chargers. It is recommended that you charge your device in environments with temperatures below 25°C / 77°F.
• Both the protective phone case and the position of your device on the wireless charger will affect the charging speed. The farther it is placed from the center of the wireless charger, the slower the charging speed will be.

Recharging Your Portable Charger

You can simultaneously recharge your PowerCore while charging your device wirelessly. The wireless charging indicator will turn solid blue, and the battery level indicator will show the current battery level.

Specifications

Cell Capacity/

USB-C Input/

| 5000mAh 3.7Vdc/18.5Wh
---|---
USB-C Output/USB-C| 5V 2.2A
Wireless Output/| 5V 2A

Total Output/

| 5W Max /     5W

10W Max / 10W

 |

Important Safety Instructions

When using this product, basic precautions should always be followed, including the following:

1.  Store product in a cool and dry place.
2.  Do not store the product in hot or humid environment.
3.  Use of a power supply or charger not recommended or sold by the product manufacturer may result in a risk of fire or injury to persons.
4.  Operating temperature should be between 32°F to 77°F / 0℃ to 25℃ .
5.  Do not disassemble the product. Take it to a qualified service person when service or repair is required. Incorrect reassembly may result in a risk of fire or injury to persons.
6.  If the product is not used for long periods of time, you should change and discharge once every three months.
7.  When charging a device, the product may feel warm, this is a normal operating condition and should not be cause for concern.
8.  In normal conditions, the battery performance will decline over several years.
9.  Do not dispose of the product in heat or fire.
10.  Do not clean the product with harmful chemicals or detergents
11.  Misuse, dropping or excessive force may cause product damage.
12. When disposing of secondary cells or batteries, keep cells or batteries of different electrochemical systems separate from each other.
13.  Be aware discharged battery may cause fire or smoke, tape the terminals to insulate them.

Notice

This product complies with the radio interference requirements of the European Community.

EU Declaration of Conformity
Hereby, Anker Innovations Limited declares that the product type A1619 is in compliance with Directives 2014/53/EU,2011/65/EU. The full text of the EU declaration of conformity is available at the following internet address: https://www.anker.com Frequency Range: 111-205kHz Max H-field: 23.74dbμA/m@3m

DISPOSAL

This symbol indicates that this product shall not be treated as household waste. Instead it shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment.

FCC Statement

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Warning: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Note : This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

•  Reorient or relocate the receiving antenna.
•  Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio / TV technician for help.

Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance of 20 cm between the radiator & your body.
The following importer is the responsible party.

References

• SCHUNK – Competence leader for toolholding and workholding, gripping technology and automation technology
• SCHUNK – Competence leader for toolholding and workholding, gripping technology and automation technology

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>