JULA 016747 Ice Cream Maker Instruction Manual
- June 6, 2024
- JULA
Table of Contents
JULA 016747 Ice Cream Maker
SAFETY INSTRUCTIONS
IMPORTANT:
Read these instructions carefully before use, and save them for future
reference. Always take basic safety precautions when using electrical
appliances to reduce the risk of fire, electric shock and/or personal injury.
- Read these instructions carefully before use.
- Remove all packaging material. Check the product, power cord, plug and all accessories for any transport damage.
- When the product has been placed where it is going to be used, leave the transparent lid open and wait at least 2 hours before using the product for the first time.
- Only use fresh drinking water in the product.
- Check that the mains voltage corresponds to the rated voltage on the type plate. The product must only be connected to a correctly earthed power point.
- If the product, power cord or plug are damaged they must
- Do not expose the product, power cord or plug to water or any other liquid, and make sure that no liquid gets into the ventilation openings on the product – risk of electric shock.
- Pull out the plug before cleaning and when the product is not in use.
- Only use accessories recommended or supplied by the manufacturer.
- This product can be used by children from 8 years and upwards and by persons with physical, sensorial or mental disabilities, or persons who lack experience or knowledge, if they a re supervised or receive instructions concerning the safe use of the product and understand the risks involved with its use. Do not allow children to play with the product. Do not allow children to clean or maintain the product without supervision.
- Do not place or use the• Do not expose the product, power cord or plug to water or any other liquid, and make sure that no liquid gets into the ventilation openings on the product – risk of electric shock.
- Pull out the plug before cleaning and when the product is not in use.
- Only use accessories recommended or supplied by the manufacturer.
- This product can be used by children from 8 years and upwards and by persons with physical, sensorial or mental disabilities, or persons who lack experience or knowledge, if they a re supervised or receive instructions concerning the safe use of the product and understand the risks involved with its use. Do not allow children to play with the product. Do not allow children to clean or maintain the product without supervision.
- Do not place or use the product near sources of heat, such as naked flames, a stove or oven, etc.
- Never put metal foil or other conductive objects in the product – risk of fire, electric shock and/or material damage.
- Do not use the product outdoors.
- The product is intended for household use, or for use in staff rooms, hotel rooms or other similar places.
- Route the power cord so that it cannot be driven over, trod on or pinched, or tripped over.
- Children from 3 to 8 years can fill and empty cooling devices.
- Recycle the product when it has reached the end of its useful life in accordance with local regulations. Do not expose the product to naked flames or other sources of heat.
WARNING!
- Do not connect the product to a power strip or portable power supply unit.
- Do not use the product if the power cord, plug or other electrical parts are damaged or not working properly. Take the product to an authorised service centre to be checked and repaired.
- Leave at least 8 cm of free space around the inlet and outlet on the product when in use to ensure adequate cooling.
- Do not use mechanical devices or other means to speed up defrosting than those recommended by the manufacturer.
- Do not store explosive or flammable substances or objects in the product, such as spray cans with propellant gas.
- Follow the instructions below to avoid damaging or contaminating food.
- The temperature inside the product can increase if the lid is left open for a long time.
- Clean all surfaces that can come into contact with food at regular intervals.
- Clean containers containing water that have not be used for 48 hours. The water system connected to the water pipe should be flushed clean if water has not been used for s days.
- Store raw meat and fish in suitable containers in the fridge so that they do not come into contact with, or drip on other food.
- Two-star compartments for frozen food are suitable for storage of frozen food, storing or making ice cream and ice cubes.
- One-, two- and threestar compartments are not suitable for freezing fresh food.
- If the product is left empty for long periods, switch off the product, defrost, clean and dry, and leave the lid open, to prevent the formation of mould inside the product.
SYMBOLS
TECHNICAL DATA
- Rated voltage 230 V ~ 50 H z
- Output 100W
- Safety class
- Environmental classification N/SN
- Refrigerant R600a/18 g
- Vesicant Cyclopentane (CsH ,o)
- Volume 1L
- Size W 26 x H 22,75 x D 35,5 cm
- Cord length 120 cm
- Weight 7.4 kg
DESCRIPTION
- Motor
- Transparent lid
- Mixer
- Ice-cream container
- Lid
- Casing
- Base unit
CONTROL PANEL
BUTTON FUNCTIONS
Power switch button
Plug in the plug and press the power switch for one second to start the
ice-cream maker. The status light for ice-cream making mode flashes red. Press
the power switch button again for one second to switch off the ice-cream
maker.
Button START/STOP
The status light flashes red when the ice-cream maker starts. Press the button
START/STOP. The status light goes green and the product starts working. Press
the button START/STOP again to stop the ice-cream maker. The status light
flashes red and the ice-cream maker stops working. The cooling mode is not
activated in run mode and in ice-cream making mode. If the button is pressed
again in this mode the status light flashes red, the mixer stops, and cooling
function is deactivated after one minute. If the button is pressed again
within one minute the ice-cream maker returns to run mode.
Menu button
Press this button when the status light is red, to select one of the three
modes. It is not possible to select mode with the menu button when the status
light is red.
3 MODES TO CHOOSE BETWEEN
-
Mixing mode
The mixer starts when this mode is activated. The time set at the factory is 30 minutes. Ten audio prompts are given to indicate that the mixing is finished when the set time has run out or the mixture of ice cream has reached the set consistency. The ice-cream maker goes into standby mode and the status light flashes red. Select another mode, or switch off the ice-cream maker. -
Cooling mode
The compressor and cooling fan start. The time set at the factory is ten minutes. Ten audio prompts are given when the set time has run out to indicate that the cooling mode has finished. The ice-cream maker goes into standby mode and the status light flashes red. Select another mode, or -
Ice-cream making mode
The compressor, mixer and cooling fan start. Ten short audio prompts are given when the ice cream is ready. The ice cream is ready to eat. Cooling mode is activated automatically and the status light flashes green if no other steps are taken. Ten short audio prompts are given when the cooling mode has finished. The ice-cream maker goes into standby mode and the status light flashes red. Select another mode, or switch off the ice-cream maker.
STATUS LIGHT
- The status light flashes red when the ice-cream maker is in standby mode.
- The status light flashes goes green when the ice-cream maker is in run mode.
- The status light flashes green when the ice-cream maker is in cooling mode.
COOLING FUNCTION
Cooling mode is activated to prevent the ice cream melting if it is not
going to be used or frozen immediately. The ice-cream maker will continue to
switch off automatically for ten minutes and then run for six minutes to
maintain the fresh taste and texture of the ice cream if no steps are taken
when the ice-cream making process is completed. This function is active for 1
hour. During this time the status light flashes green. Ten short audio prompts
are given when the ice-cream making process is completed, the ice-cream maker
goes into standby mode, and the status light flashes red.
MOTOR SAFETY FUNCTION
The mixer can be blocked when the ice cream gets harder and the motor safety function trips to stop the motor.
COMPRESSOR SAFETY FUNCTION
If the ice-cream maker is switched off in ice-cream making mode or cooling
mode, it cannot be started again for about three minutes to protect the
compressor. When the plug is plugged in the ice-cream maker starts
automatically, without delay.
USE
ICE-CREAM MAKING
- Pour the well prepared recipe ingredients in proportion into the removable bowl, then have a uniform mixing.
- Put the ice-cream container in the ice- cream maker. Fit both ends of the handle in the slot in the upper casing. Installation position for ice-cream container
- Fit the transparent lid and motor unit.
- Fit the mixer on the transparent lid and motor unit.
- Put the mixer with the transparent lid and motor unit on the ice-cream maker and fit the mixer motor on the ice-cream container. Turn the mixer unit clockwise to lock, so that the arrow on the unit points to the lock marking.
- Plug in the plug and press the power switch for one second to start the ice- cream maker. The status light flashes red. Press the button START/STOP. The status light flashes green and the ice-cream making process starts.
- Press the power switch button for one second to switch off the ice-cream maker when the ice-cream making process is completed.
- Turn the transparent lid and motor unit anticlockwise. A faint scraping noise is heard. This is perfectly normal. When the arrow on the transparent lid points to the marking for unlocked position, lift out the mixer unit and the ice-cream container
.
NOTE:
- Before using, clean all parts that come into contact with the ice-cream mixture thoroughly, such as the cooling unit, ice-cream container, mixer and lid etc.
- Switch off the ice-cream maker and pull out the plug. Place the ice-cream maker on a level, stable surface, otherwise the compressor might not work properly.
- Do not tilt the ice-cream maker more than 45° and do not turn it upside down.
- When the ice-cream maker has been switched off, wait at least five minutes before starting it again, otherwise the compressor can be damaged.
- Do not subject the surface or edge of the container to knocks when taking out the ice cream, this can damage the container.
- Never start the ice-cream maker unless the ice-cream container and mixer are correctly fitted.
- The initial temperature of the ice-cream mixture should be 25 ± 5°C. The mixture should not be cooled or frozen before it is placed in the ice-cream maker. This will cause the ice cream to solidify too quickly, and to block and switch off the motor with the motor safety function.
- When the ice-cream making process has started, do not switch off the motor or open the transparent lid until the process is completed.
- Switch off the ice-cream maker and pull out the plug after use.
- A faint noise when the mixer scrapes against the container will be heard if the ice-cream maker is started without ice cream. This is perfectly normal.
- There are two round copper plates on the transparent lid over the motor. Wipe off any water from the copper plates and the transparent lid before using the ice-cream maker. Water can short circuit the two copper plates, which will cut out the power supply to the motor. If this happens, switch off the ice-cream maker and pull out the plug, wipe off the water and start the ice-cream maker again.
MAINTENANCE
CLEANING
- Remove the mixer and wipe it with a damp cloth.
- Remove the ice-cream container and clean it with a soft, damp cloth.
- Wipe the transparent lid and the lid over the ice-cream container with a damp cloth.
- Remove any impurities on the base unit and other parts with a damp cloth.
- Wipe thoroughly with a dry cloth and fit all the parts.
WARNING!
- Pull out the plug before cleaning and maintenance, otherwise there is a risk of electric shock.
- Do not expose the power cord or plug to water or any other liquid, or submerge the base unit, and make sure that no liquid gets into the ventilation openings on the ice-cream maker.
- Do not use detergent or metal utensils, abrasive or scratching utensils when cleaning. Do not wash the ice-cream maker in a dishwasher. Do not expose the evaporator to water.
PROBLRM
It is not possible to remove the ice-cream container when the mixing is ready.
| CAUSE
Droplets of water have frozen between the cooling unit and the ice-cream container.
| ACTION
Wait 3-8 minutes and then remove the ice-cream
container.
---|---|---
It is not possible to put the
ice-cream container correctly in
the cooling unit
| The container has been deformed as a result of
incorrect handling.
|
Get hold of a new container.
---|---|---
The mixer scrapes or fastens in the container.
| The container has been deformed as a result of incorrect handling.|
Get hold of a new container.