JULA 010258 Laminating Machine Instruction Manual
- June 4, 2024
- JULA
Table of Contents
JULA 010258 Laminating Machine
SAFETY INSTRUCTIONS
- Read the instructions carefully before use and save them for future reference.
- For indoor use only.
- Check that the mains voltage corresponds to the rated voltage on the type plate.
- Place the product on a stable surface, so that it cannot fall off and get damaged or cause personal injury.
- Do not attempt to laminate sheets thicker than 0.4 mm.
- Never insert objects in the product other than those described in these instructions. Keep your hair, clothing, hands, jewellery and other foreign objects away from the product.
- Switch off the product with the power switch after use.
- Switch off the product and pull out the plug before cleaning and/or servicing, before moving the product and if the product is not going to be used for some time.
- Switch off the product immediately and pull out the plug if the product is not working properly. Contact the retailer.
- Keep the product under careful supervision when it is used near children.
- Be careful with the power cord. Do not pull the power cord to pull out the plug. Do not use the product if the power cord or plug are damaged, or if the product is not working properly.
- Do not dismantle the product or attempt to modify, or repair it. Contact the retailer in the event of any problems.
WARNING!
- Do not overload the power cord or power point – risk of fire and/or electric shock.
- Do not cover the ventilation openings on the product – risk of overheating.
- Do not expose the product to rain or moisture.
- Do not touch the power cord or the plug with wet hands.
- Do not immerse the product in water or any other liquid.
SYMBOLS
- Read the instructions.
- Approved in accordance with the relevant directives.
- Recycle discarded product in accordance with local regulations.
TECHNICAL DATA
- Rated voltage 230 V, 50~60 Hz
- Thickness, laminating pouches 80-125 μm
- Lamination width 238 mm
- Max thickness of sheets
- to be laminated 0.4 mm
- Feed speed 300 mm/min
- Size 315x115x68 mm
- Weight 1.1 kg
DESCRIPTION
Power switch/mode selector- Power light
- Status light
- lnfeed opening
- Outfeed opening
- Power cord
USE
- Check that the power switch is switched off before plugging in the power cord.
- Plug in the power cord.
- The red status light goes on and the motor starts. The green status light is off.
- Wait until the product has warmed up (4-8 minutes). The product is ready to start laminating when the green status light goes on.
- Place the sheet to be laminated in a laminating pouch. Leave 3-10 mm between the sheet and the closed end of the laminating pouch. Cut the laminating pouch if the sheet to be laminated is smaller than the laminating pouch.
- Insert the laminating pouch in the product w ith the closed end first, otherwise there is a risk of the pouch folding and getting stuck.
- The laminating pouch is fed automatically through the product.
- When the laminating pouch is fed out it is warm and soft. Handle it with care. Allow it to cool on a flat surface or pressed between flat objects, e.g. books.
NOTE:
The first fw times the product is used some materials in the product may emit
a slight smell. This is quite normal. Contact the retailer if the smell does
not go away after a few hours.
MAINTENANCE
- Unplug the power cord before cleaning. Clean the product casing with a damp cloth.
- Clean the rollers regularly for the best laminating quality.
- Clean the rollers by running a clean sheet of pape r through the appliance several times.
WARNING!
Do not use abrasive or solvent-based detergents, or aerosol products.
TROUBLESHOOTING
Laminating pouch gets stuck
The status lights are on but the laminating pouch does not feed through the
product, which resu lts in abnormal noise and burning.
Cause
- The laminating pouch has not been cut to fit the sheet to be laminated, which makes the laminating film fasten on the rollers, or the sheet has been placed too far from the closed end of the laminating pouch.
- The sheet to be laminated is too thick (> 0.4 mm)
Action
Switch off the product immediately if the laminating pouch gets stuck. Pull
out the laminating pouch through the infeed opening and try again with new
material. Contact the retailer if the problem persists. Do not attempt to
correct the problem yourself.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>