HOLMAN WX1 Tap Timer and Wi-Fi Hub Setup Apps User Guide
- June 6, 2024
- Holman
Table of Contents
For the #SMARTGARDENER
ADDING YOUR Wi-Fi HUB TO HOLMAN HOME USING AP MODE
-
Plug your Wi-Fi Hub into a power source near your Wi-Fi router
-
Open Holman Home and add a new device by tapping plus [a] on the HOME screen
-
Tap GARDEN WATERING [b] and choose Wi-Fi HUB [c]
-
Enter your Wi-Fi network [d] and password [e], then tap NEXT [f]
-
On the following screen, tap EZ MODE [g]
-
From the drop-down menu, tap AP MODE [h]
-
Reset the Wi-Fi Hub as per the instructions provided on-screen [i]
-
Once the Wi-Fi Hub is flashing accordingly, check the LED confirmation toggle [j] and tap NEXT [k] The Wi-Fi Hub has three flashing modes:
• Fast flash
• Slow flash
• Slow long blink -
On the following screen, tap GO TO CONNECT [l]
-
apple iOS only: If redirected to SETTINGS, tap Wi-Fi [m]
-
apple iOS only: Tap Holman-WX-XXXX [n] and wait until the network is connected
-
android Android only: Tap the Holman-WX-XXXX [o] and wait until the network is connected
apple iOS or android Android: If the Holman-WX-XXXX network does not show in your Wi-Fi settings, try the following:
Disable Wi-Fi on your smartphone, wait a few moments and turn Wi-Fi back on
You may need to reset your Wi-Fi Hub again; Hold the button for approximately 5 seconds to change to fast-flash mode, then hold the button again for approx 5 seconds to change back to slow-flash mode -
android Android only: Ignore messages such as “Connected without internet” and tap chevron-left in the Android nav bar to ignore[p]
-
android Android only: Once Holman-WX-XXXX is the active network, return to Holman Home using by tapping the multi-screen icon [q]
-
iOS only: Once Holman-WX-XXXX is the active network [r], return to Holman Home using by tapping the Holman Home shortcut [s]
-
Wait while your Wi-Fi Hub is being added to Holman Home [t]
-
If your Wi-Fi Hub [u] connects successfully, tap DONE [v]
-
After confirming the connection, tap ADD/VIEW DEVICES [w] and follow the prompts to connect the Wi-Fi Socket and WX1 Tap Timer
If this method of connecting the WX1 Tap Timer and Wi-Fi Sockedoes not work, tap the back button [x] to go back to the HOME screen, and follow the next set of instructions for an alternative connection method
ADDING YOUR WX1 TAP TIMER AND Wi-Fi SOCKET TO HOLMAN HOME
-
Ensure your WX1 Tap Timer is close to your router and install 4× 1.5v AA alkaline batteries [a]
-
From the HOME screen tap plus [b] to add the WX1 Tap Timer and Wi-Fi Socket
https://support.holmanindustries.com.au/?=qr -
Tap GARDEN WATERING [c] and choose WX1 Tap Timer [d] When a GATEWAY [e] is requested, select Wi-Fi HUB [f]
-
Reset the WX1 Tap Timer as per the instructions provided on-screen [g]
-
Once the WX1 Tap Timer is flashing accordingly, check the LED confirmation toggle [h] and tap NEXT [i] If your WX1 Tap Timer fails to add to Holman Home, restart the app, and start the process again to add your WX1 Tap Timer and Wi-Fi Socket
-
Wait until both the WX1 Tap Timer [j] and Wi-Fi Socket [k] have been added, then tap DONE [l]
WX1 Setup Process Workaround
For additional help, visit https://www.holmanindustries.com.au/
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>