K RCHER IVM 100/36-3 Oss Industrial Vacuum Cleaners User Manual

K RCHER IVM 100/36-3 Oss Industrial Vacuum Cleaners

Product Information

The IVM 100/36-3 Oss is a vacuum cleaner designed for both dry and wet cleaning applications. It has a powerful suction turbine and a built-in filter that can be cleaned or replaced as needed. The device has a large capacity for storing dry debris and a separate tank for liquids. The vacuum cleaner comes with a variety of accessories for different cleaning tasks and is suitable for both commercial and residential use.

Product Usage Instructions

Before using the IVM 100/36-3 Oss, read the user manual carefully and adhere to the instructions provided. Ensure that you have read the safety instructions (no. 5.956-249.0) before the initial startup to avoid any dangers that may arise for you or other persons.

Installation

1. Connect the device to a power source with the appropriate voltage and phase.
2. Attach the desired accessory to the hose and wand assembly.
3. Place the suction hose into the suction nozzle.
4. Turn on the device and begin cleaning.

Operation

1. Clean or replace the filter as needed (refer to the manual for instructions).
2. When switching from wet to dry cleaning, make sure the filter is dried or replaced with a dry filter.

Care and Maintenance

1. Turn off the suction turbine and unplug the device from the power source.
2. Clean the device with a damp cloth and dry it thoroughly.
3. Clean or replace the filter as needed (refer to the manual for instructions).

Transport
When transporting the device, make sure it is securely fastened and cannot tip over or fall.

Storage
When storing the device, make sure it is in a dry, safe place where it will not be damaged or cause a hazard.

Disposal
Dispose of the device in accordance with local regulations for electronic waste.

Guarantee
The device comes with a warranty. Refer to the manual for details on the warranty and how to make a claim.

Product Technical specifications

The device has the following technical specifications:

• Net voltage: 220-240V
• Net frequency: 50-60Hz
• Power: 3150W
• Protection class: IPX4 I*
• Noise level: 79 dB(A)
• Cable type: H07R N-F 3G1,5 mm2

General instructions
Read these original instructions before using your device for the first time, adhere to the instructions contained therein and store them for later reference or subsequent owners.

• Be sure to read the safety instructions no. 5.956-249.0 prior to the initial startup.
• If the operating instructions and safety instructions are not observed, the device can be damaged and dangers could arise for users and other persons.
• Notify the dealer immediately in the case of shipping damage.

Safety information

Hazard levels

• DANGER
  Indication of an imminent threat of danger that will lead to severe injuries or even death.

• WARNING
  Indication of a potentially dangerous situation that may lead to severe injuries or even death.

• CAUTION
  Indication of a potentially dangerous situation that may lead to minor injuries.

• ATTENTION
  Indication of a potentially dangerous situation that may lead to damage to property.

General safety instructions
It is essential to read the enclosed safety instructions for wet/dry vacuum cleaners before using the device for the first time!

• DANGER Observe the applicable safety instructions for the materials being vacuumed.
• WARNING
  • The device is not suitable for vacuuming up dusts that are harmful to human health.
  • The device must not be used or stored outdoors in wet conditions.
  • Apply the parking brake at the steering roller to ensure a secure footing for the device. The device may move uncontrollably if the parking brake is open.
• CAUTION In case of longer breaks in operation and after use, switch off the device at the power switches and unplug the mains plug.

Behavior in the event of an emergency

DANGER
Risk of injury and damage in the event of a short-circuit or other electrical faults

The danger of electric shock, the danger of burns Switch off the device and unplug the mains plug.

Intended use

The device is intended for:

• Wet and dry cleaning of floor and wall surfaces
• For vacuuming moist or liquid substances
• For vacuuming dry, non-flammable dust from machines
• Industrial use, e.g. in storage and production areas and on production machinery

Any other use constitutes improper use. The device must not be used for the following purposes:

• Vacuuming dangerous dust
• Crane loading

Environmental protection
The packing materials can be recycled. Please dispose of the packaging in accordance with the environmental regulations.

Electrical and electronic appliances contain valuable, recyclable materials and often components such as batteries, rechargeable batteries or oil, which – if handled or disposed of incorrectly – can pose a potential threat to human health and the environment. However, these components are required for the correct operation of the appliance. Appliances marked by this symbol are not allowed to be disposed of together with household rubbish.

Notes on the content materials (REACH)
Current information on content materials can be found at: www.kaercher.com/REACH.

Accessories and spare parts
Only use original accessories and original spare parts. They ensure that the appliance will run fault-free and safely. Information on accessories and spare parts can be found at www.kaercher.com.

Description of the unit

For the illustrations, refer to the graphics page Illustration A

1. Steering roller with the parking brake
2. Floor nozzle holder
3. Dirt receptacle
4. Cable clips
5. Push handle
6. Suction pipe holder
7. Filter ring
8. Spacer
9. Type plate
10. Suction head
11. Carrying handle
12. filter
13. Sealing ring
14. Filter vibrator
15. Lever for the filter cleaning
16. Illuminated pressure switch
17. Suction turbine power switch
18. Cable hooks
19. Mains cable
20. Suction headlock
21. Spacer lock
22. Suction hose port
23. Bow handle of the dirt receptacle
24. Fill level sensor plug
25. Fill level sensor
26. Chassis

Initial startup

ATTENTION

Exceeding the grid impedance
Electrical shock in the event of a short-circuit The maximum permissible mains grid impedance at the electrical connection point (see Technical data) must not be exceeded.

Contact your electricity supplier in the case of any uncertainties regarding the mains grid impedance at your electrical connection point.

1. Bring the device into the working position.
2. Secure the device with the parking brakes.
3. Insert the suction hose into the suction connection.
4. Plug the desired accessory onto the suction hose.
5. If necessary, fit a dust collection bag in the dirt receptacle (see Chapter Fitting the dust collection bag).
6. Ensure that the dirt receptacle is correctly fitted.

Fitting the dust collection bag
A dust collection bag can be inserted into the dirt receptacle to allow dust- free emptying of the device.

Note
The dust collection bag must not be used for wet vacuum cleaning.

1. Fit the dust collection bag in the dirt receptacle and carefully press it against the wall of the container.

2. Fold the edge of the bag over the edge of the dirt receptacle.
   WARNING
   Improper handling when locking the dirt receptacle
   Risk of crushing
   Under no circumstances should you hold your hands between the dirt receptacle and filter ring or allow them to come close to the lifting mechanism while locking it. Lock the dirt receptacle by operating the bow handle with both hands.

3. Fit the dirt receptacle in the device.

Operation

After vacuuming moist or liquid substances, see chapter Switching from wet to dry vacuuming.

Switching on the unit

1. Plug the mains plug into the socket. The illuminated pressure switch lights up. Illustration B

2. Press the illuminated pressure switch. The light goes out.

3. Switch on the device via the suction turbine power switches.
   Note
   Select the required suction power via the suction turbine power switch, starting with suction turbine 1. Always switch the suction turbines on and off one after the other.

4. Start the vacuuming process.

Performing the vacuuming process

Note
The unit has a fill level sensor that automatically switches the unit off when the dirt receptacle is full.

1. If necessary, but at the latest when the fill level sensor switches off the unit, empty the dirt receptacle (see chapter Emptying the dirt receptacle).
2. If necessary, clean the filter (see chapter Cleaning the filter) or change/replace the filter (see chapter Changing/replacing the filter).

Wet vacuum cleaning

ATTENTION

Risk of damage if the dirt receptacle overflows
The dirt receptacle can fill within a few seconds and overflow when vacuuming large amounts of liquids.

Continuously monitor the filling level.

1. Remove the dust collection bag, if necessary, before wet vacuum cleaning (see chapter Emptying the dirt receptacle).
2. After wet vacuum cleaning:
   • Dry the filter.
   • Clean the dirt receptacle with a moist cloth and dry it off.

Switching from wet to dry vacuuming

ATTENTION

Switching from wet to dry vacuuming

Risk of damage to the filter
Do not vacuum dry dust with a wet filter element because this clogs the filter and can make it unusable.

1. Allow the wet filter to dry completely or replace it with a dry filter before using the device for dry vacuuming.
2. Replace the filter if necessary.

Cleaning the filter
Clean the star-pleated filter at regular intervals.

1. Switch off the device.
2. If dry suction material has been extracted, move the filter cleaning lever back and forth at least 5 times.

If this cleaning does not bring any improvement, remove the star pleated filter and wash or replace it (see chapter Care and Maintenance).

Switching off the device

1. Switch off the device via the suction turbine power switches.
2. Pull out the mains plug.

Each time after use

1. Remove the accessories.
2. Remove the accessories and, if necessary, flush with water and allow to dry.
3. Empty the dirt receptacle (see chapter Emptying the dirt receptacle).
4. Vacuum the inside and outside of the device and clean it with a moist cloth.
5. Remove the filter for drying if the wet suction material has been vacuumed.

Emptying the dirt receptacle

WARNING

Risk of crushing
When removing or replacing the container, watch for moving parts.

Note
Empty the dirt receptacle when the unit switches off automatically and the illuminated pressure switch lights up.

1. Switch off the device at the power switches.

2. Secure the device with the parking brakes.

3. If dry suction material has been extracted, move the filter cleaning lever back and forth at least 5 times. Illustration C

4. Pull the bow handle up. The dirt receptacle is unlocked and lowered.

5. Pull the dirt receptacle out of the device by the bow handle.

6. Remove the dust collection bag if necessary.

   • Close the dust collection bag and remove it from the dirt receptacle.
   • Dispose of the dust collection bag and contents according to the applicable waste disposal regulations.

7. Empty the dirt receptacle.
   Note
   The dirt receptacle can be lifted by a crane at the handle. The maximum load for transport by crane is 50 kg.
   CAUTION
   Exceeding the permissible total weight
   Risk of injury and damage
   Observe the total weight of the dirt receptacle when transporting it by crane. Do not overload the receptacle. Observe the valid instructions for crane operation.

8. WARNING
   Improper handling when locking the dirt receptacle
   Risk of crushing
   Under no circumstances should you hold your hands between the dirt receptacle and filter ring or allow them to come close to the lifting mechanism while locking it. Lock the dirt receptacle by operating the bow handle with both hands.

9. Insert the dirt receptacle into the device in reverse order. Illustration B

10. Press the illuminated pressure switch. The light goes out.

Transport

CAUTION

Failure to observe the weight
Risk of injury and damage

Be aware of the weight of the device during transportation.

1. Secure the device against slipping and tipping over when transporting in vehicles.

Storage

CAUTION

Failure to observe the weight
Risk of injury and damage

Be aware of the weight of the device during storage.

1. Store the device indoors only.

Care and maintenance

DANGER

Disconnecting the fill level sensor plug
Risk of electric shock

The fill level sensor plug may only be disconnected by trained specialists or service personnel.

Inspection and maintenance work
Have the device regularly inspected according to the respective national accident prevention regulations. Maintenance work as specified by the manufacturer must be performed by a technically qualified person at the specified regular intervals and in ac-cordance with the applicable regulations and safety requirements. Work on electrical components may only be performed by a qualified electrician. Please contact a KÄRCHER branch office if you have any questions.

Maintenance intervals/user maintenance
No periodic maintenance intervals are specified for this device. The following maintenance is to be performed as necessary:

• Wash the filter.
• Change the filter.
• Replace the filter.

Wash the filter

ATTENTION

Use of detergents or bleach
Damage to the filter.

Clean the filter with water only. Only fit the filter in the device when it is completely dry. The star-folded filter can be washed out under running water.

1. Always flush the star-folded filter from the inside to the outside so that no remaining particles impair the filter performance.

Changing/replacing the filter

1. Switch off the device.

2. Pull out the mains plug.
   ATTENTION
   Incorrect removal of the suction head Damage to the plug of the fill level sensor Is careful not to damage the fill level sensor connector when removing the suction head. Place the suction head near the unit so that the cable of the level sensor plug is not stretched.

3. Unlock and remove the suction head.

4. Unlock and remove the spacer.

5. Remove the star-pleated filter.

6. Check the sealing ring for damage.

7. Insert the new star pleated filter:

   • Pull the new star-pleated filter over the filter vibrator on the spacer such that the vibrating elements are aligned centrally in the filter bags.
   • Place the spacer with star pleated filter and filter vibrator on the filter ring.
   • Lock the spacer.

8. Fit and lock the suction head.

Troubleshooting guide

DANGER

Unintentional start-up of the device/electric shock
Unintentional start-up of the suction motor can cause injuries. Voltage present on electrical parts can cause an electric shock. Switch off the device and unplug the mains plug before performing any work on the device.

Have all checks and work on electrical parts performed by a qualified technician.

Note
The device must be switched off immediately in the event of a malfunction. The malfunction must be eliminated before switching the device on again. If the malfunction cannot be corrected, the device must be checked by the Customer Service department.

The suction turbine does not start up

1. Check the socket and the power supply fuse.
2. Check the mains cable and the mains plug of the device.
3. Switch the device on.

Suction power decreases

1. Remove the blockages from the suction nozzle, the suction pipe or the suction hose.
2. Clean the filter (see chapter Cleaning the filter).
3. Empty the dirt receptacle (see chapter Emptying the dirt receptacle).

Escaping dust when vacuuming

1. Check the seating of the filter and correct if necessary.
2. Clean the filter (see chapter Cleaning the filter).
3. Replace the filter (see chapter Changing/replacing the filter).

Disposal
At the end of its service life, the device is to be disposed of in accordance with statutory regulations.

Warranty

The warranty conditions issued by our relevant sales company apply in all countries. We shall remedy possible malfunctions on your appliance within the warranty period free of cost, provided that a material or manufacturing defect is the cause. In a warranty case, please contact your dealer (with the purchase receipt) or the next authorized customer service site. (See overleaf for the address)

Technical data

Electrical connection

• Mains voltage V 220- 240
• Phase ~ 1
• Power frequency Hz 50-60
• Power W 3150
• Protection class IPX4
• Protection class I*
• Maximum permissible mains grid impedance Ω 0.195+ j0.122

Dimensions and weights

• Typical operating weight kg 76
• Length x width x height mm 1020 x 680 x 1720
• Filter area m2 2.24

Ambient conditions

• Storage temperature °C -10-40

Device performance data

• Container capacity l 100
• Vacuum (with pressure relief valve) kPa 25.4
• Air quantity l/s 3 x 74
• Suction hose connection NW DN70
• Nominal width of the suction hose DN40/50/70
• Filter order number 6.907- 611.0

Determined values in acc. with EN 60335-2-69

• Hand-arm vibration value m/s2 < 2.5
• Uncertainty K m/s2 0.2
• Sound pressure level LpA dB(A) 79
• Uncertainty KpA dB(A) 2

Mains cable

• Type H07R N-F 3G1.5 mm2
• Part number 6.650- 035.0
• Cable length m 10

With elements of protection class II arrangement Subject to technical changes without notice.

Declaration of Conformity

EU Declaration of Conformity

We hereby declare that the machine described below complies with the relevant basic safety and health requirements in the EU Directives, both in its basic design and construction as well as in the version placed in circulation by us. This declaration is invalidated by any changes made to the machine that are not approved by us.

• Product: Dry vacuum cleaner
• Product: Wet/dry vacuum cleaner
• Type: 9.990-xxx

Currently applicable EU Directives
2006/42/EC (+2009/127/EC)

• 2014/30/EU
• 2011/65/EU

Harmonized standards used

• EN 60335-1
• EN 60335-2-69
• EN 55014-1: 2017 + A11: 2020
• EN 55014-2: 2015
• EN IEC 61000-3-2: 2019
• EN 61000-3-3: 2013 + A1: 2019
• EN 61000-3-11: 2000
• EN 62233: 2008
• EN IEC 63000: 2018

National standards used
The signatories act on behalf of and with the authority of the company management.

• Managing partner
  M.Pfister

Kärcher Industrial Vacuuming GmbH

• Robert-Bosch-Straße 4-8 73550 Waldstetten (Germany)
• Ph.: +49 7171 94888-0
• Fax: +49 7171 94888-528
• Waldstetten, 21/11/01

Declaration of Conformity (UK)
We hereby declare that the product described below complies with the relevant provisions of the following UK Regulations, both in its basic design and construction as well as in the version put into circulation by us. This declaration shall cease to be valid if the product is modified without our prior approval.

• Product: Dry vacuum cleaner
• Product: Wet/dry vacuum cleaner
• Type: 9.990-xxx

Currently applicable UK Regulations

• S.I. 2008/1597 (as amended)
• S.I. 2016/1091 (as amended)
• S.I. 2012/3032 (as amended)

Designated standards used

• EN 60335-1
• EN 60335-2-69

http://www.kaercher.com/dealersearch.

References

• Cher - Official Site
• her.com
• Cleaning equipment and pressure washers | Kärcher International
• Cleaning equipment and pressure washers | Kärcher International

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>