Fanvil i10S SIP Mini Intercom Installation Guide

June 6, 2024
Fanvil

Fanvil i10S SIP Mini Intercom

Fanvil i10S SIP Mini Intercom
PROD

Package Contents

Fanvil i10S SIP Mini Intercom
FIG1

Physical specification

Device size 88 x 88 x 32 mm
i10S No camera, 1 button
i10SV With camera, 1 button
i10SD No camera, 2 button

PanelFanvil i10S SIP Mini Intercom FIG2

Interface description

Open the rear case of the device, there is a row of terminal blocks for connecting the power supply, indoor switch. The connection is as follows:Fanvil i10S SIP Mini Intercom FIG3

Serial number Description

| Ethernet interface: standard

RJ45 interface, 10/100M adaptive, it is recommended to use five or five types of network cable

②| Power interface: 12V/1A input
③| A set of short-circuit output interfaces
④| A set of short-circuit input interfaces

Installation Diagram

Fanvil i10S SIP Mini Intercom
FIG4

Installation of rubber plug:

  • Wall mount: Attach the installation dimension drawing to the position to be installed, use the electric drill to punch the hole in the 2 screw holes marked, and use the hammer to drive the rubber plug into the drilled hole.
  • Built-in: Attach the installation dimension drawing to the position to be installed, open a groove of the same size according to the size, use the electric drill to punch the hole in the 2 screw holes marked, and use the hammer to drive the rubber plug into the drilled hole.
  • Remove the cover;
  • Use a screwdriver to remove the 4 screws on the main body to separate the main body from the rear case;
  • Pass all the wires through the hole in the lower right corner of the bottom case. All lines must be reserved for a length of 15~20CM;
  • Fix the housing
  • Wall Mount: Align the bottom case with the position of the screw hole that was previously punched on the wall, and screw in the two screws with a screwdriver to fix the bottom case to the wall;
  • Built-in: Place the bottom case into the previously opened groove and screw in the two screws with a screwdriver to secure the bottom case to the wall;
  • Connect power, network and control cables, and the test whether there is electricity by doing the following:
  • Long press DSS key for 3 seconds(after power-on for 30 seconds), and when the speaker beeps rapidly, press DSS key again quickly, the beeps stop ,the intercom will report the IP address by itself.
  • If the work is normal, continue with the next steps.
  • Lock the 4 screws removed in step 3;
  • Cover the cover removed in step 2;

Searching device

Methods 1:
Download address: http://download.fanvil.com/tool/iDoorPhoneNetworkScanner.exe Open the door phone Network Scanner. Press the Refresh button to search the device and find the IP address.Fanvil i10S SIP Mini Intercom FIG5

Method 2:
Long press DSS key for 3 seconds(after power-on for 30 seconds), and when the speaker beeps rapidly, press DSS key again quickly, the beeps stop ,the intercom will report the IP address by itself.

Method 3:
In addition, device provides the device surface DSS key operation to switch IP address acquisition mode: In the standby mode, long-press the DSS key for 3 seconds and the beep will last for 5 seconds. Within 5 seconds, press the DSS key three times quickly to switch to the network mode.

  • If it is in the mode of DHCP and doesn’t receive the IP address, switch it to the mode of static IP (192.168.1.128), broadcast the IP address after the successful switch.
  • If it is in the mode of static IP address (192.168.1.128), switch it to the DHCP mode, broadcast the IP address after the successful switch.
  • If it is in the mode of DHCP and obtain the IP address, the mode will not be switched and directly broadcast the IP.

Default Setting

Default DHCP Client|

Enabled by default

| Static IP address|

192.168.1.128

Default DHCP Client

| Hold the DSS key for 3 seconds, then press the DSS key again.|

Default Web port

|

80

Fast settings

Step 1: Log in to the device page
Use the web browser input IP (for example http://192.168.1.128) access. The default user and password are admin.Fanvil i10S SIP Mini Intercom
FIG6

Step 2: Set SIP account
Set SIP server address, port, user name, password and SIP user with assigned SIP account parameters. Select “Activate”, and then click [Apply] to save this setting.Fanvil i10S SIP Mini Intercom FIG7

Step 3: Set the volume (if not connected can skip) Intercom settings => Media Settings => Media Settings Set the device volume size, as shown below, click [Apply].

Speakerphone volume setting: set the speaker volume of normal calls.

Handsfree Mic Gain: set the microphone volume of call.Fanvil i10S SIP
Mini Intercom FIG8

Step 4: Set function key (if not connected can skip)
Set the function key as shown below for a quick start, click [Apply] to save this setting.

Type: Memory key
Number 1 (Value): the function key will dial to this number 1
Number 2 (Value 2): if number 1 is unavailable, it will be forwarded to number 2.

Subtype: speed dial
Line: working lineFanvil i10S SIP Mini Intercom
FIG9

Step 5: Set the security function
1 set of short-circuit input and output settings, tamper alarm server settings.

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals