ASRock H570 Steel Legend Instructions
- June 6, 2024
- ASRock
Table of Contents
- Package Contents
- Specifications
- Installing the CPU Fan and Heatsink
- Installing Memory Modules (DIMM)
- Expansion Slots (PCI Express Slots)
- Jumpers Setup
- Onboard Headers and Connectors
- M.2 WiFi/BT Module and Intel® CNVi (Integrated WiFi/BT)
- M.2_SSD (NGFF) Module Installation Guide (M2_1)
- M.2_SSD (NGFF) Module Support List (M2_1)
- M.2_SSD (NGFF) Module Installation Guide (M2_2)
- ASRock Polychrome SYNC
- ASRock Polychrome SYNC Utility
- References
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
http://www.asrock.com/manual.asp?Model=H570%20Steel%20Legend
Version 1.0
Published February 2021
Copyright©2021 ASRock INC. All rights reserved.
Copyright Notice:
No part of this documentation may be reproduced, transcribed, transmitted, or
translated in any language, in any form or by any means, except duplication of
documentation by the purchaser for backup purpose, without written consent of
ASRock Inc.
Products and corporate names appearing in this documentation may or may not be
registered trademarks or copyrights of their respective companies, and are
used only for identification or explanation and to the owners’ benefit,
without intent to infringe.
Disclaimer:
Specifications and information contained in this documentation are furnished
for informational use only and subject to change without notice, and should
not be constructed as a commitment by ASRock. ASRock assumes no responsibility
for any errors or omissions that may appear in this documentation. With
respect to the contents of this documentation, ASRock does not provide
warranty of any kind, either expressed or implied, including but not limited
to the implied warranties or conditions of merchantability or fitness for a
particular purpose.
In no event shall ASRock, its directors, officers, employees, or agents be
liable for any indirect, special, incidental, or consequential damages
(including damages for loss of profits, loss of business, loss of data,
interruption of business and the like), even if ASRock has been advised of the
possibility of such damages arising from any defect or error in the
documentation or product.
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference
that may cause undesired operation.
CALIFORNIA, USA ONLY
The Lithium battery adopted on this motherboard contains Perchlorate, a toxic
substance controlled in Perchlorate Best Management Practices (BMP)
regulations passed by the
California Legislature. When you discard the Lithium battery in California,
USA, please follow the related regulations in advance.
“Perchlorate Material-special handling may apply, see
www.dtsc.ca.gov/hazardouswaste/perchlorate”
ASRock Website: http://www.asrock.com
AUSTRALIA ONLY
Our goods come with guarantees that cannot be excluded under the Australian
Consumer Law. You are entitled to a replacement or refund for a major failure
and compensation for any other reasonably foreseeable loss or damage caused by
our goods. You are also entitled to have the goods repaired or replaced if the
goods fail to be of acceptable quality and the failure does not amount to a
major failure. If you require assistance please call ASRock Tel
: +886-2-28965588 ext.123 (Standard International call charges apply)
The terms HDMI® and HDMI High-Definition Multimedia Interface, and the HDMI
logo are trademarks or registered trademarks of HDMI Licensing LLC in the
United
States and other countries.
INTEL END USER SOFTWARE LICENSE AGREEMENT
IMPORTANT – READ BEFORE COPYING, INSTALLING OR USING.
LICENSE. Licensee has a license under Intel’s copyrights to reproduce Intel’s
Software only in its unmodified and binary form, (with the accompanying
documentation, the “Software”) for Licensee’s personal use only, and not
commercial use, in connection with Intel-based products for which the Software
has been provided, subject to the following conditions:
(a) Licensee may not disclose, distribute or transfer any part of the
Software, and You agree to prevent unauthorized copying of the Software.
(b) Licensee may not reverse engineer, decompile, or disassemble the Software.
(c) Licensee may not sublicense the Software.
(d) The Software may contain the software and other intellectual property of
third party suppliers, some of which may be identified in, and licensed in
accordance with, an enclosed license.txt file or other text or file.
(e) Intel has no obligation to provide any support, technical assistance or
updates for the Software.
OWNERSHIP OF SOFTWARE AND COPYRIGHTS. Title to all copies of the Software
remains with Intel or its licensors or suppliers. The Software is copyrighted
and protected by the laws of the United States and other countries, and
international treaty provisions. Licensee may not remove any copyright notices
from the Software. Except as otherwise expressly provided above, Intel grants
no express or implied right under Intel patents, copyrights, trademarks, or
other intellectual property rights. Transfer of the license terminates
Licensee’s right to use the Software.
DISCLAIMER OF WARRANTY. The Software is provided “AS IS” without warranty of
any kind, EITHER EXPRESS OR IMPLIED, INCLUDING WITHOUT LIMITATION, WARRANTIES
OF MERCHANTABILITY OR FITNESS FOR ANY PARTICULAR PURPOSE. LIMITATION OF
LIABILITY. NEITHER INTEL NOR ITS LICENSORS OR SUPPLIERS WILL BE LIABLE FOR ANY
LOSS OF PROFITS, LOSS OF USE, INTERRUPTION OF BUSINESS, OR INDIRECT, SPECIAL,
INCIDENTAL, OR CONSEQUENTIAL DAMAG-
ES OF ANY KIND WHETHER UNDER THIS AGREEMENT OR OTHERWISE, EVEN IF INTEL HAS
BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. LICENSE TO USE COMMENTS AND
SUGGESTIONS. This Agreement does NOT obligate Licensee to provide Intel with
comments or suggestions regarding the Software. However, if Licensee provides
Intel with comments or suggestions for the modification, correction,
improvement or enhancement of (a) the Software or (b) Intel products or
processes that work with the Software, Licensee grants to Intel a non-
exclusive, worldwide, perpetual, irrevocable, transferable, royalty-free
license, with the right to sublicense, under Licensee’s intellectual property
rights, to incorporate or otherwise utilize those comments and suggestions.
TERMINATION OF THIS LICENSE. Intel or the sublicensor may terminate this
license at any time if Licensee is in breach of any of its terms or
conditions. Upon termination, Licensee will immediately destroy or return to
Intel all copies of the Software. THIRD PARTY BENEFICIARY. Intel is an
intended beneficiary of the End User License Agreement and has the right to
enforce all of its terms. U.S. GOVERNMENT RESTRICTED RIGHTS. The Software is a
commercial item (as defined in 48 C.F.R. 2.101) consisting of commercial
computer software and commercial computer software documentation (as those
terms are used in 48 C.F.R. 12.212), consistent with 48 C.F.R. 12.212 and 48
C.F.R 227.7202-1 through 227.7202-4. You will not provide the Software to the
U.S. Government. Contractor or Manufacturer is Intel Corporation, 2200 Mission
College Blvd., Santa Clara, CA 95054.
EXPORT LAWS. Licensee agrees that neither Licensee nor Licensee’s subsidiaries
will export/re-export the Software, directly or indirectly, to any country for
which the U.S.
Department of Commerce or any other agency or department of the U.S.
Government or the foreign government from where it is shipping requires an
export license, or other governmental approval, without first obtaining any
such required license or approval. In the event the Software is exported from
the U.S.A. or re-exported from a foreign destination by Licensee, Licensee
will ensure that the distribution and export/re-export or import of the
Software complies with all laws, regulations, orders, or other restrictions
of the U.S.Export Administration Regulations and the appropriate foreign
government. APPLICABLE LAWS. This Agreement and any dispute arising out of or
relating to it will be governed by the laws of the U.S.A. and Delaware,
without regard to conflict of laws principles. The Parties to this Agreement
exclude the application of the United Nations Convention on Contracts for the
International Sale of Goods (1980). The state and federal courts sitting in
Delaware, U.S.A. will have exclusive jurisdiction over any dispute arising out
of or relating to this Agreement. The Parties consent to personal jurisdiction
and venue in those courts. A Party that obtains a judgment against the other
Party in the courts identified in this section may enforce that judgment in
any court that has jurisdiction over the Parties.
Licensee’s specific rights may vary from country to country.
H570 Steel Legend
Motherboard Layout
No | Description |
---|---|
1 | ATX 12V Power Connector (ATX12V1) |
2 | ATX 12V Power Connector (ATX12V2) |
3 | CPU Fan Connector (CPU_FAN1) |
4 | 2 x 288-pin DDR4 DIMM Slots (DDR4_A1, DDR4_B1) |
5 | 2 x 288-pin DDR4 DIMM Slots (DDR4_A2, DDR4_B2) |
6 | CPU/Water Pump Fan Connector (CPU_FAN2/WP) |
7 | RGB LED Header (RGB_LED2) |
8 | Addressable LED Header (ADDR_LED2) |
9 | Chassis/Water Pump Fan Connector (CHA_FAN3/WP) |
10 | ATX Power Connector (ATXPWR1) |
11 | USB 3.2 Gen1 Header (USB3_3_4) |
12 | Chassis/Water Pump Fan Connector (CHA_FAN1/WP) |
13 | Front Panel Type C USB 3.2 Gen2x2 Header (F_USB31_TC_1) |
14 | USB 3.2 Gen1 Header (USB3_5_6) |
15 | SATA3 Connectors (SATA3_4)(Upper), (SATA3_5)(Lower) |
16 | SATA3 Connectors (SATA3_2)(Upper), (SATA3_3)(Lower) |
17 | SATA3 Connectors (SATA3_0)(Upper), (SATA3_1)(Lower) |
18 | Chassis/Water Pump Fan Connector (CHA_FAN4/WP) |
19 | System Panel Header (PANEL1) |
20 | Power LED and Speaker Header (SPK_PLED1) |
21 | SPI TPM Header (SPI_TPM_J1) |
22 | Clear CMOS Jumper (CLRMOS1) |
23 | USB 2.0 Header (USB_5_6) |
24 | USB 2.0 Header (USB_3_4) |
25 | RGB LED Header (RGB_LED1) |
26 | Addressable LED Header (ADDR_LED1) |
27 | Front Panel Audio Header (HD_AUDIO1) |
28 | Thunderbolt AIC Connector (TB1) |
29 | Chassis/Water Pump Fan Connector (CHA_FAN2/WP) |
I/O Panel
No. | Description |
---|---|
1 | USB 2.0 Ports (USB_1_2) |
2 | USB 3.2 Gen2 Type-A Port (USB31_TA_1) |
3 | 2.5G LAN RJ-45 Port* |
4 | Line In (Light Blue)** |
5 | Front Speaker (Lime)** |
6 | Microphone (Pink)** |
7 | USB 3.2 Gen1 Ports (USB3_1_2) |
8 | USB 3.2 Gen2 Type-C Port (USB31_TC_1) |
9 | DisplayPort 1.4 |
10 | HDMI Port |
11 | PS/2 Mouse/Keyboard Port |
- There are two LEDs on each LAN port. Please refer to the table below for the LAN port LED indications.
Activity / Link LED
Status | Description |
---|---|
Off | No Link |
Blinking | Data Activity |
On | Link |
Off | 10Mbps connection |
Orange | 100Mbps/1Gbps connection |
Green | 2.5Gbps connection |
** Function of the Audio Ports in 7.1-channel Configuration:
Port | Function |
---|---|
Light Blue (Rear panel) | Rear Speaker Out |
Lime (Rear panel) | Front Speaker Out |
Pink (Rear panel) | Central /Subwoofer Speaker Out |
Lime (Front panel) | Side Speaker Out |
Chapter 1 Introduction
Thank you for purchasing ASRock H570 Steel Legend motherboard, a reliable
motherboard produced under ASRock’s consistently stringent quality control. It
delivers excellent performance with robust design conforming to ASRock’s
commitment to quality and endurance.
Because the motherboard specifications and the BIOS software might be updated,
the content of this documentation will be subject to change without notice. In
case any modifications of this documentation occur, the updated version will
be available on ASRock’s website without further notice. If you require
technical support related to
this motherboard, please visit our website for specific information about the
model you are using. You may find the latest VGA cards and CPU support list on
ASRock’s website as well. ASRock website
http://www.asrock.com.
Package Contents
- ASRock H570 Steel Legend Motherboard (ATX Form Factor)
- ASRock H570 Steel Legend Quick Installation Guide
- ASRock H570 Steel Legend Support CD
- 2 x Serial ATA (SATA) Data Cables (Optional)
- 4 x Screws for M.2 Sockets (Optional)
- 1 x Standoff for M.2 Socket (Optional)
- 1 x I/O Panel Shield
Specifications
Platform| • ATX Form Factor
• Solid Capacitor design
---|---
CPU| • Supports 10 the Gen Intel® Core TM Processors and 11 the Gen
Intel® Core TM Processors (LGA1200)
• Digi Power design
• 8 Power Phase design
• Supports Intel® Turbo Boost Max 3.0 Technology
Chipset| • Intel® H570
Memory| • Dual Channel DDR4 Memory Technology
• 4 x DDR4 DIMM Slots
• 11 the Gen Intel® Core TMProcessors support DDR4 non-ECC, un-buffered
memory up to 4800+(OC) th
• 10 Gen Intel® Core TMProcessors support DDR4 non-ECC, un-buffered memory up
to 4666+(OC) the 11 Gen Intel® Core TM(i9/i7/i5) support DDR4 up to
3200; TM
Core (i3), Pentium® and Celeron® support DDR4 up to 2666. the 10 Gen Intel®
Core
TM (i9/i7) support DDR4 up to 2933; Core TM (i5/i3), Pentium® and Celeron®
support DDR4 up to 2666. Please refer to Memory Support List on ASRock’s
website for
more information. (http://www.asrock.com/) • Supports ECC UDIMM memory
modules (operate in nonECC mode)
• Max. capacity of system memory: 128GB
• Supports Intel® Extreme Memory Profile (XMP) 2.0
Expansion| 11 th Gen Intel® Core TM Processors
Slot| • 2 x PCI Express x16 Slots (PCIE1/PCIE3: single at Gen4x16
(PCIE1); dual at Gen4x16 (PCIE1) / Gen3x4 (PCIE3)) th 10 Gen Intel® Core TM
Processors
• 2 x PCI Express x16 Slots (PCIE1/PCIE3: single at Gen3x16 (PCIE1); dual at
Gen3x16 (PCIE1) / Gen3x4 (PCIE3)) Supports NVMe SSD as boot disks• 3 x PCI
Express 3.0 x1 Slots • Supports AMD Quad CrossFireX TM and CrossFireX TM
• 1 x M.2 Socket (Key E), supports type 2230 WiFi/BT module and Intel® CNVi
(Integrated WiFi/BT)
Graphics| * Intel® UHD Graphics Built-in Visuals and the VGA outputs can
be supported only with processors which are GPU integrated.
• 11 th Gen Intel® Core TM Processors support Intel® X e Graphics
Architecture (Gen 12). 10 th Gen Intel® Core TM Processors support Gen 9
Graphics
• Graphics, Media & Compute: Microsoft DirectX 12, OpenGL 4.5, Intel® Built In
Visuals, Intel® Quick Sync Video, Hybrid / Switchable Graphics, OpenCL 2.1
• Display & Content Security: Rec. 2020 (Wide Color Gamut), Microsoft
PlayReady 3.0, UHD/HDR Blu-ray Disc
• Dual graphics output: support HDMI and DisplayPort 1.4 ports by independent
display controllers
• Supports HDMI 2.0 with max. resolution up to 4K x 2K (4096×2160) @ 60Hz
• Supports DisplayPort 1.4 with max. resolution up to 4K x 2K (4096×2304) @
60Hz
• Supports Auto Lip Sync, Deep Color (12bpc), xvYCC and HBR (High Bit Rate
Audio) with HDMI 2.0 Port (Compliant HDMI monitor is required)
• Supports HDCP 2.3 with HDMI 2.0 and DisplayPort 1.4 Ports
• Supports 4K Ultra HD (UHD) playback with HDMI 2.0 and DisplayPort 1.4 Ports
-
11 th Gen Intel® Core TM Processors support HDMI 2.0. 10 thGen Intel® Core
TM Processors support HDMI 1.4.
Audio| • 7.1 CH HD Audio (Realtek ALC897 Audio Codec)
• Supports Surge Protection
• Nahimic Audio
LAN| • 2.5 Gigabit LAN 10/100/1000/2500 Mb/s
• Dragon RTL8125BG
• Supports Dragon 2.5G LAN Software
– Smart Auto Adjust Bandwidth Control
– Visual User Friendly UI
– Visual Network Usage Statistics
– Optimized Default Setting for Game, Browser, and Streaming Modes
– User Customized Priority Control
• Supports Wake-On-LAN
• Supports Lightning/ESD Protection
• Supports Energy Efficient Ethernet 802.3az
• Supports PXE
Rear Panel| • 1 x PS/2 Mouse/Keyboard Port
I/O| • 1 x HDMI Port
• 1 x DisplayPort 1.4
• 1 x USB 3.2 Gen2 Type-A Port (10 Gb/s) (ReDriver) (Supports ESD Protection)
• 1 x USB 3.2 Gen2 Type-C Port (10 Gb/s) (ReDriver) (Supports ESD Protection)
• 2 x USB 3.2 Gen1 Ports (Supports ESD Protection)
• 2 x USB 2.0 Ports (Supports ESD Protection)
• 1 x RJ-45 LAN Port with LED (ACT/LINK LED and SPEED LED)
• HD Audio Jacks: Line in / Front Speaker / Microphone
Storage| • 6 x SATA3 6.0 Gb/s Connectors, support RAID (RAID 0,
RAID 1, RAID 5, RAID 10, Intel Rapid Storage Technology 18), NCQ, AHCI and Hot Plug* -
If M2_2 is occupied by a SATA-type M.2 device, SATA3_1 will be disabled.
-
If M2_2 is occupied by a PCIe-type M.2 device, SATA3_0 will be disabled.
-
If M2_3 is occupied by a SATA-type M.2 device, SATA3_2 will be disabled.• 1 x Hyper M.2 Socket (M2_1), supports M Key type
2260/2280 M.2 PCI Express module up to Gen4x4 (64 Gb/s) (Only supported with 11
Processors)
• 1 x Ultra M.2 Socket (M2_2), supports M Key type 2260/2280 M.2 SATA3 6.0 Gb/s module and M.2 PCI Express module up to Gen3 x4 (32 Gb/s)
• 1 x Ultra M.2 Socket (M2_3), supports M Key type 2260/2280/22110 M.2 SATA3 6.0 Gb/s module and M.2 PCI Express module up to Gen3 x4 (32 Gb/s) th Gen Intel® Core TM Technolog y
Supports NVMe SSD as boot disks
Supports ASRock U.2 Kit
Supports Intel® Optane TM
Connector| • 1 x SPI TPM Header
• 1 x Power LED and Speaker Header
• 2 x RGB LED Headers -
Support in total up to 12V/3A, 36W LED Strip
• 2 x Addressable LED Headers -
Support in total up to 5V/3A, 15W LED Strip
• 1 x CPU Fan Connector (4-pin) -
The CPU Fan Connector supports the CPU fan of maximum 1A (12W) fan power.
• 1 x CPU/Water Pump Fan Connector (4-pin) (Smart Fan Speed Control) -
The CPU/Water Pump Fan supports the water cooler fan of maximum 2A (24W) fan power.
• 4 x Chassis/Water Pump Fan Connectors (4-pin) (Smart Fan Speed Control) -
The Chassis/Water Pump Fan supports the water cooler fan of maximum 2A (24W) fan power.
-
CPU_FAN2/WP, CHA_FAN1/WP, CHAFAN2/WP, CHA FAN3/WP and CHA_FAN4/WP can auto detect if 3-pin or 4-pin fan is in use.
• 1 x 24 pin ATX Power Connector
• 1 x 8 pin 12V Power Connector (Hi-Density Power Connector)
• 1 x 4 pin 12V Power Connector (Hi-Density Power Connector)
• 1 x Front Panel Audio Connector
• 1 x Thunderbolt AIC Connector (5-pin) (Supports ASRock Thunderbolt 4 AIC Card)
• 2 x USB 2.0 Headers (Support 4 USB 2.0 ports) (Supports ESD Protection)
• 2 x USB 3.2 Gen1 Headers (Support 4 USB 3.2 Gen1 ports) (ASMedia ASM1074 hub) (Supports ESD Protection)
• 1 x Front Panel Type C USB 3.2 Gen2x2 Header (20 Gb/s) (Supports ESD Protection)
BIOS| • AMI UEFI Legal BIOS with multilingual GUI support
Feature| • ACPI 6.0 Compliant wake up events
• SMBIOS 2.7 Support
• CPU Core/Cache, CPU GT, DRAM, VCCIO, VCCSA,
VCCST, VCCIN AUX, VPPM Voltage Multi-adjustment
Hardware| • Fan Tachometer: CPU, CPU/Water Pump, Chassis/Water
Pump Fans
---|---
Monitor| • Quiet Fan (Auto adjust chassis fan speed by CPU temperature): CPU, CPU/Water Pump, Chassis/Water Pump Fans
• Fan Multi-Speed Control: CPU, CPU/Water Pump, Chassis/ Water Pump Fans
• Voltage monitoring: CPU Vcore, PCH, DRAM, VCCIO,
VPPM, VCCSA, CPU PLL, +12V, +5V, +3.3V
OS| • Microsoft® Windows® 10 64-bit
Certifications| • FCC, CE
• ErP/EuP ready (ErP/EuP ready power supply is required) -
For detailed product information, please visit our website: http://www.asrock.com
Please realize that there is a certain risk involved with overclocking, including adjusting the setting in the BIOS, applying Untied Overclocking Technology, or using third-party overclocking tools. Overclocking may affect your system’s stability, or even cause damage to the components and devices of your system. It should be done at your own risk and expense. We are not responsible for possible damage caused by overclocking.
Chapter 2 Installation
This is an ATX form factor motherboard. Before you install the motherboard,
study the configuration of your chassis to ensure that the motherboard fits
into it.
Pre-installation Precautions
Take note of the following precautions before you install motherboard
components or change any motherboard settings.
-
Make sure to unplug the power cord before installing or removing the motherboard components. Failure to do so may cause physical injuries and damages to motherboard
components. -
In order to avoid damage from static electricity to the motherboard’s components, NEVER place your motherboard directly on a carpet. Also remember to use a grounded wrist strap or touch a safety grounded object before you handle the components.
-
Hold components by the edges and do not touch the ICs.
-
Whenever you uninstall any components, place them on a grounded anti-static pad or in the bag that comes with the components.
-
When placing screws to secure the motherboard to the chassis, please do not overtighten the screws! Doing so may damage the motherboard.
2.1 Installing the CPU
- Before you insert the 1200-Pin CPU into the socket, please check if the PnP cap is on the socket, if the CPU surface is unclean, or if there are any bent pins in the socket. Do not force to insert the CPU into the socket if the above situation is found. Otherwise, the CPU will be seriously damaged.
- Unplug all power cables before installing the CPU.
Please save and replace the cover if the processor is removed. The cover must be placed if you wish to return the motherboard for after service.
Installing the CPU Fan and Heatsink
Installing Memory Modules (DIMM)
This motherboard provides four 288-pin DDR4 (Double Data Rate 4) DIMM slots, and supports Dual Channel Memory Technology.
- For dual channel configuration, you always need to install identical (the same brand, speed, size and chip-type) DDR4 DIMM pairs.
- It is unable to activate Dual Channel Memory Technology with only one or three memory module installed.
- It is not allowed to install a DDR, DDR2 or DDR3 memory module into a DDR4 slot; otherwise, this motherboard and DIMM may be damaged.
Dual Channel Memory Configuration
Priority | DDR4_A1 | DDR4_A2 | DDR4_B1 | DDR4_B2 |
---|---|---|---|---|
1 | Populated | Populated | ||
2 | Populated | Populated | Populated | Populated |
The DIMM only fits in one correct orientation. It will cause permanent damage to the motherboard and the DIMM if you force the DIMM into the slot at incorrect orientation.
Expansion Slots (PCI Express Slots)
There are 5 PCI Express slots on the motherboard.
Before installing an expansion card, please make sure that the power supply is switched off or the power cord is unplugged. Please read the documentation of the expansion card and make the necessary hardware settings for the card before you start the installation.
PCIe slots:
11th Gen Intel® Core TM Processors:
PCIE1 (PCIe 4.0 x16 slot) is used for PCI Express x16 lane width graphics
cards.
PCIE2 (PCIe 3.0 x1 slot) is used for PCI Express x1 lane width cards.
PCIE3 (PCIe 3.0 x16 slot) is used for PCI Express x4 lane width graphics
cards.
PCIE4 (PCIe 3.0 x1 slot) is used for PCI Express x1 lane width cards.
PCIE5 (PCIe 3.0 x1 slot) is used for PCI Express x1 lane width cards.
10th Gen Intel® Core TM Processors:
PCIE1 (PCIe 3.0 x16 slot) is used for PCI Express x16 lane width graphics
cards.
PCIE2 (PCIe 3.0 x1 slot) is used for PCI Express x1 lane width cards.
PCIE3 (PCIe 3.0 x16 slot) is used for PCI Express x4 lane width graphics
cards.
PCIE4 (PCIe 3.0 x1 slot) is used for PCI Express x1 lane width cards.
PCIE5 (PCIe 3.0 x1 slot) is used for PCI Express x1 lane width cards.
PCIe Slot Configurations
11th Gen Intel® Core TM Processors
| PCIE1| PCIE3
---|---|---
Single Graphics Card| Gen4x16| N/A
Two Graphics Cards in CrossFireX
TM Mode| Gen4x16| Gen3x4
10th Gen Intel® Core TM Processors
| PCIE1| PCIE3
---|---|---
Single Graphics Card| Gen3x16| N/A
Two Graphics Cards in CrossFireX
TM Mode| Gen3 x16| Gen3x4
For a better thermal environment, please connect a chassis fan to the motherboard’s chassis fan connector (CHA_FAN1/WP, CHA_FAN2/WP, CHA_FAN3/WP or CHA_FAN4/WP) when using multiple graphics cards.
Jumpers Setup
The illustration shows how jumpers are setup. When the jumper cap is placed on the pins, the jumper is “Short”. If no jumper cap is placed on the pins, the jumper is “Open”.
Clear CMOS Jumper
(CLRMOS1)
(see p.1, No. 22)
CLRMOS1 allows you to clear the data in CMOS. To clear and reset the system parameters to default setup, please turn off the computer and unplug the power cord from the power supply. After waiting for 15 seconds, use a jumper cap to short the pins on CLRMOS1 for 5 seconds. However, please do not clear the CMOS right after you update the BIOS. If you need to clear the CMOS when you just finish updating the BIOS, you must boot up the system first, and then shut it down before you do the clear-CMOS action. Please be noted that the password, date, time, and user default profile will be cleared only if the CMOS battery is removed. Please remember toremove the jumper cap after clearing the CMOS.
Onboard Headers and Connectors
Onboard headers and connectors are NOT jumpers. Do NOT place jumper caps over these headers and connectors. Placing jumper caps over the headers and connectors will cause permanent damage to the motherboard.
System Panel Header (9-pin PANEL1) (see p.1, No. 19)
Connect the power button, reset button and system status indicator on the chassis to this header according to the pin assignments below. Note the positive and negative pins before connecting the cables.
PWRBTN (Power Button):
Connect to the power button on the chassis front panel. You may configure the
way to turn off your system using the power button.
RESET (Reset Button):
Connect to the reset button on the chassis front panel. Press the reset button
to restart the computer if the computer freezes and fails to perform a normal
restart.
PLED (System Power LED):
Connect to the power status indicator on the chassis front panel. The LED is
on when the system is operating. The LED keeps blinking when the system is in
S1/S3 sleep
state. The LED is off when the system is in S4 sleep state or powered off
(S5).
HDLED (Hard Drive Activity LED):
Connect to the hard drive activity LED on the chassis front panel. The LED is
on when the hard drive is reading or writing data.
The front panel design may differ by chassis. A front panel module mainly
consists of power button, reset button, power LED, hard drive activity LED,
speaker and etc.
When connecting your chassis front panel module to this header, make sure the
wire assignments and the pin assignments are matched correctly.
Power LED and Speaker
Header
(7-pin SPK_PLED1)
(see p.1, No. 20)| | Please connect the
chassis power LED and
the chassis speaker to this
header.
---|---|---
Serial ATA3 Connectors
Right-Angle:
(SATA3_0:
see p.1, No. 17)(Upper)
(SATA3_1:
see p.1, No. 17)(Lower)
(SATA3_2:
see p.1, No. 16)(Upper)
(SATA3_3:
see p.1, No. 16)(Lower)
(SATA3_4:
see p.1, No. 15)(Upper)
(SATA3_5:
see p.1, No. 15)(Lower)| | These six SATA3
connectors support SATA
data cables for internal
storage devices with up to
6.0 Gb/s data transfer rate.
-
If M2_2 is occupied by
a SATA-type M.2 device,
SATA3_1 will be disabled. -
If M2_2 is occupied by
a PCIe-type M.2 device,
SATA3_0 will be disabled. -
If M2_3 is occupied by
a SATA-type M.2 device,
SATA3_2 will be disabled.
---|---|---
USB 2.0 Headers
(9-pin USB_3_4)
(see p.1, No. 24)
(9-pin USB_5_6)
(see p.1, No. 23)| | There are two USB
2.0 headers on this
motherboard. Each USB
2.0 header can support two
ports.
---|---|---
USB 3.2 Gen1 Headers
Vertical:
(19-pin USB3_3_4)
(see p.1, No. 11)| | There are two headers on
this motherboard. Each
USB 3.2 Gen1 header can
support two ports.
Right-Angle:
(19-pin USB3_5_6)
(see p.1, No. 14)| |
Front Panel Audio Header
(9-pin HD_AUDIO1)
(see p.1, No. 27)| | This header is for connecting audio devices
to the front audio panel.-
High Definition Audio supports Jack Sensing, but the panel wire on the chassis must support HDA to function correctly. Please follow the instructions in our
manual and chassis manual to install your system. -
If you use an AC’97 audio panel, please install it to the front panel audio header by the steps below:
A. Connect Mic_IN (MIC) to MIC2_L.
B. Connect Audio_R (RIN) to OUT2_R and Audio_L (LIN) to OUT2_L.
C. Connect Ground (GND) to Ground (GND).
D. MIC_RET and OUT_RET are for the HD audio panel only. You don’t need to connect them for the AC’97 audio panel.
E. To activate the front mic, go to the “FrontMic” Tab in the Realtek Control panel and adjust “Recording Volume”.
-
Chassis/Water Pump Fan
Connectors
(4-pin CHA_FAN1/WP)
(see p.1, No. 12)
(4-pin CHA_FAN2/WP)
(see p.1, No. 29)
(4-pin CHA_FAN3/WP)
(see p.1, No. 9)
(4-pin CHA_FAN4/WP)
(see p.1, No. 18)| | This
motherboard provides four 4-Pin water cooling chassis fan connectors. If you
plan to connect a 3-Pin chassis water cooler fan,
please connect it to Pin 1-3.
---|---|---
CPU Fan Connector
(4-pin CPU_FAN1)
(see p.1, No. 3)| | This motherboard provides a 4-Pin CPU fan (Quiet Fan)
connector. If you plan to connect a 3-Pin CPU fan, please connect it to Pin
1-3.
CPU/Water Pump Fan Connector
(4-pin CPU_FAN2/WP) (see p.1, No. 6)| | This motherboard provides a 4-Pin
water cooling CPU fan connector. If you plan
to connect a 3-Pin CPU water cooler fan, please connect it to Pin 1-3.
ATX Power Connector
(24-pin ATXPWR1)
(see p.1, No. 10)| | This motherboard provides a 4-Pin water cooling CPU fan
connector. If you plan
to connect a 3-Pin CPU water cooler fan, please connect it to Pin 1-3.
ATX 12V Power Connector
(8-pin ATX12V1)
(see p.1, No. 1)| | This motherboard provides an 8-pin ATX 12V power
connector. To use a 4-pin ATX power supply, please plug it along Pin 1 and Pin
5. Warning: Please make sure that the power cable connected is for the CPU
and not the graphics card. Do not plug the PCIe power cable to this
connector.
ATX 12V Power
Connector
(4-pin ATX12V2)
(see p.1, No. 2)| | Please connect an ATX 12V power supply to this
connector.
The power supply plug fits into this connector in only one orientation.
Connecting an ATX 12V 4-pin cable to ATX12V2 is optional.
For advanced overclocking we suggest
using this connector together with ATX12V1.
Front Panel Type C USB
3.2 Gen2x2 Header
(20-pin F_USB31_TC_1(see p.7, No. 13)| | There is one Front Panel Type C USB
3.2
Gen2x2 Header on this motherboard. This header is used for connecting a USB
3.2 Gen2x2 module for additional USB 3.2 Gen2x2 ports.
SPI TPM Header
(13-pin SPI_TPM_J1)
(see p.1, No. 21)| | This connector supports SPI Trusted
Platform Module (TPM) system, which can securely store keys, digital
certificates,
passwords, and data. A TPM system also helps enhance network security,
protects digital identities, and ensures platform integrity.
Thunderbolt AIC
Connector
(5-pin TB1)
(see p.1, No. 28)| | Please connect a Thunderbolt™ add-in card
(AIC) to this connector via the GPIO cable.
Please install the Thunderbolt™
AIC card to PCIE3 (default slot).
RGB LED Headers
(4-pin RGB_LED1)
(see p.1, No. 25)| | RGB headers are used to connect RGB LED extension
cables which allow users to choose from various LED lighting effects.
(4-pin RGB_LED2)
(see p.1, No. 7)| | Caution: Never install the RGB LED cable in the
wrong orientation; otherwise, the cable may be damaged.
Please refer to page 39 for further instructions on this header.
Addressable LED Headers
(3-pin ADDR_LED1)
(see p.1, No. 26)| | These headers are used to connect Addressable LED
extension cables which allow users to choose from various LED lighting
effects.
(3-pin ADDR_LED2)
(see p.1, No. 8)| | Caution: Never install the Addressable
LED cable in the wrong orientation; otherwise,the cable may be damaged.
*Please refer to page 40 for further instructions on this header.
M.2 WiFi/BT Module and Intel® CNVi (Integrated WiFi/BT)
Installation Guide
The M.2, also known as the Next Generation Form Factor (NGFF), is a small size and versatile card edge connector that aims to replace mPCIe and mSATA. The M.2 Socket (Key E) supports type 2230 WiFi/BT module and Intel® CNVi (Integrated WiFi/BT).
- The M.2 socket does not support SATA M.2 SSDs.
Before you install Intel® Integrated Connectivity (CNVi) module, be sure to turn off the AC power.
Installing the WiFi/BT module
Step 1
Prepare a type 2230 WiFi/BT module or Intel® CNVi (Integrated WiFi/BT) and the
screw.
Step 2
Find the nut location to be used.
Step 3
Gently insert the WiFi/BT module or Intel® CNVi (Integrated WiFi/ BT) into the
M.2 slot. Please be aware that the module only fits in one orientation.
Step 4
Tighten the screw with a screwdriver to secure the module into place. Please
do not overtighten the screw as this might damage the module.
M.2_SSD (NGFF) Module Installation Guide (M2_1)
The M.2, also known as the Next Generation Form Factor (NGFF), is a small size
and versatile card edge connector that aims to replace mPCIe and mSATA. The
Hyper M.2 Socket (M2_1) supports M Key type 2260/2280 M.2 PCI Express module
up to Gen4x4 (64 Gb/s) (Only supported with 11 th Gen Intel® Core TM
Processors).
Installing the M.2_SSD (NGFF) Module
Step 1
Prepare a M.2_SSD (NGFF) module and the screw.
Step 2
Before installing a M.2 (NGFF) SSD module, please loosen the screws to remove
the M.2 heatsink.
*Please remove the protective films on the bottom side of the M.2 heatsink before you install a M.2 SSD module.
Step 3
Depending on the PCB type and length of your M.2_SSD (NGFF) module, find the
corresponding nut location to be used.
No. | 1 | 2 |
---|---|---|
Nut Location | A | B |
PCB Length | 6cm | 8cm |
Module Typ | Ty pe2260 | Ty pe 2280 |
Step 4
Prepare the M.2 standoff that comes with the package. Then hand tighten the
standoff into the desired nut location on the motherboard. Align and gently
insert the M.2 (NGFF) SSD module into the M.2 slot. Please be aware that the
M.2 (NGFF) SSD module only fits in one orientation.![ASRock H570 Steel Legend
- Tighten the screw t](https://manuals.plus/wp- content/uploads/2022/03/ASRock-H570-Steel-Legend-Tighten-the- screw-t-550x296.png)
Step 5
Tighten the screw that comes with the package with a screwdriver to secure the
module into place.
Step 6
Tighten the screw with a screwdriver to secure the module and M.2 heatsink
into place. Please do not overtighten the screw as this might damage the
module and M.2 heatsink.
M.2_SSD (NGFF) Module Support List (M2_1)
Vendor | Interface | P/N |
---|---|---|
ADATA | PCIe3 x4 | ASX7000NP-128GT-C |
ADATA | PCIe3 x4 | ASX8000NP-256GM-C |
ADATA | PCIe3 x4 | ASX7000NP-256GT-C |
ADATA | PCIe3 x4 | ASX8000NP-512GM-C |
ADATA | PCIe3 x4 | ASX7000NP-512GT-C |
Apacer | PCIe3 x4 | AP240GZ280 |
Corsair | PCIe3 x4 | CSSD-F240GBMP500 |
Intel | PCIe3 x4 | SSDPEKKF256G7 |
Intel | PCIe3 x4 | SSDPEKKF512G7 |
Kingston | PCIe3 x4 | SKC1000/480G |
Kingston | PCIe3 x4 | SH2280S3/480G |
OCZ | PCIe3 x4 | RVD400 -M2280-512G (NVME) |
PATRIOT | PCIe3 x4 | PH240GPM280SSDR NVME |
Plextor | PCIe3 x4 | PX-128M8PeG |
Plextor | PCIe3 x4 | PX-1TM8PeG |
Plextor | PCIe3 x4 | PX-256M8PeG |
Plextor | PCIe | PX-512M8PeG |
Plextor | PCIe | PX-G256M6e |
Plextor | PCIe3 x4 | PX-G512M6e |
Samsung | PCIe3 x4 | SM961 MZVPW128HEGM (NVM) |
Samsung | PCIe3 x4 | PM961 MZVLW128HEGR (NVME) |
Samsung | PCIe3 x4 | 960 EVO (MZ-V6E250) (NVME) |
Samsung | PCIe3 x4 | 960 EVO (MZ-V6E250BW) (NVME) |
Samsung | PCIe3 x4 | SM951 (NVME) |
Samsung | PCIe3 x4 | SM951 (MZHPV256HDGL) |
Samsung | PCIe3 x4 | SM951 (MZHPV512HDGL) |
Samsung | PCIe3 x4 | SM951 (NVME) |
Samsung | PCIe | XP941-512G (MZHPU512HCGL) |
SanDisk | PCIe | SD6PP4M-128G |
SanDisk | PCIe3 x4 | SD6PP4M-256G |
TEAM | PCIe3 x4 | TM8FP2240G0C101 |
TEAM | PCIe3 x4 | TM8FP2480GC110 |
WD | PCIe3 x4 | WDS256G1X0C-00ENX0 (NVME) |
WD | PCIe3 x4 | WDS512G1X0C-00ENX0 (NVME) |
For the latest updates of M.2_SSD (NFGG) module support list, please visit our website for details: http://www.asrock.com
M.2_SSD (NGFF) Module Installation Guide (M2_2)
The M.2, also known as the Next Generation Form Factor (NGFF), is a small size
and versatile card edge connector that aims to replace mPCIe and mSATA. The
Ultra M.2
Socket (M2_2) supports M Key type 2260/2280 M.2 SATA3 6.0 Gb/s module and M.2
PCI Express module up to Gen3 x4 (32 Gb/s).
- If M2_2 is occupied by a SATA-type M.2 device, SATA3_1 will be disabled.
- If M2_2 is occupied by a PCIe-type M.2 device, SATA3_0 will be disabled.
Installing the M.2_SSD (NGFF) Module
Step 1
Prepare a M.2_SSD (NGFF) module and the screw.
Step 2
Depending on the PCB type and length of your M.2_SSD (NGFF) module, find the
corresponding nut location to be used.
No. | 1 | 2 |
---|---|---|
Nut Location | A | B |
PCB Length | 6cm | 8cm |
Module Type | Ty pe 2260 | Ty pe 2280 |
Step 3
Move the standoff based on the module type and length. The standoff is placed
at the nut location B by default. Skip Step 3 and 4 and go straight to Step 5
if you are going to use the default nut. Otherwise, release the standoff by
hand.
Step 4
Peel off the yellow protective film on the nut to be used. Hand tighten the
standoff into the desired nut location on the motherboard.
Step 5
Gently insert the M.2 (NGFF) SSD module into the M.2 slot. Please be aware
that the M.2 (NGFF) SSD module only fits in one orientation.
Step 6
Tighten the screw with a screwdriver to secure the module into place. Please
do not overtighten the screw as this might damage the module.
Vendor | Interface | P/N |
---|---|---|
ADATA | SATA3 | AXNS330E-32GM-B |
ADATA | SATA3 | AXNS381E-128GM-B |
ADATA | SATA3 | AXNS381E-256GM-B |
ADATA | SATA3 | ASU800NS38-256GT-C |
ADATA | SATA3 | ASU800NS38-512GT-C |
ADATA | PCIe3 x4 | ASX7000NP-128GT-C |
ADATA | PCIe3 x4 | ASX8000NP-256GM-C |
DATA | PCIe3 x4 | ASX7000NP-256GT-C |
DATA | PCIe3 x4 | ASX8000NP-512GM-C |
ADATA | PCIe3 x4 | ASX7000NP-512GT-C |
Apacer | PCIe3 x4 | AP240GZ280 |
Corsair | SATA3 | CSSD-F240GBMP500 |
Corsair | SATA3 | CT120M500SSD4 |
Corsair | SATA3 | CT240M500SSD4 |
Intel | PCIe3 x4 | Intel SSDSCKGW080A401/80G |
Intel | PCIe3 x4 | SSDPEKKF256G7 |
Intel | SATA3 | SSDPEKKF512G7 |
Kingston | PCIe3 x4 | SM2280S3 |
Kingston | PCIe2 x4 S | SKC1000/480G |
Kingston | PCIe3 x4 | SH2280S3/480G |
OCZ | PCIe3 x4 | RVD400 -M2280-512G (NVME) |
PATR IOT | PCIe3 x4 | PH240GPM280SSDR NVME |
Plextor | PCIe3 x4 | PX-128M8PeG |
Plextor | PCIe3 x4 | PX-1TM8PeG |
Plextor | PCIe3 x4 | PX-256M8PeG |
Plextor | PCIe | PX-512M8PeG |
Plextor | PCIe | PX-G256M6e |
Plextor | PCIe3 x4 | PX-G512M6e |
Samsung | PCIe3 x4 | SM961 MZVPW128HEGM (NVM) |
Samsung | PCIe3 x4 | PM961 MZVLW128HEGR (NVME) |
Samsung | PCIe3 x4 | 960 EVO (MZ-V6E250) (NVME) |
Samsung | PCIe3 x4 | 960 EVO (MZ-V6E250BW) (NVME) |
Samsung | PCIe3 x4 | SM951 (NVME) |
Samsung | PCIe3 x4 | SM951 (MZHPV256HDGL) |
Samsung | PCIe3 x4 | SM951 (MZHPV512HDGL) |
Samsung | PCIe | SM951 (NVME) |
Samsung | PCIe | XP941-512G (MZHPU512HCGL) |
SanDisk | SATA3 | SD6PP4M-128G |
SanDisk | SATA3 | SD6PP4M-256G |
Team | SATA3 | TM4PS4128GMC105 |
Team | SATA3 | TM4PS4256GMC105 |
Team | PCIe3 x4 | TM8PS4128GMC105 |
Team | PCIe3 x4 | TM8PS4256GMC105 |
TEAM | SATA3 | TM8FP2240G0C101 |
TEAM | SATA3 | TM8FP2480GC110 |
Transcend | SATA3 | TS256GMTS400 |
Transcend | SATA3 | TS512GMTS600 |
Transcend | SATA3 | TS512GMTS800 |
V-Color | SATA3 | VLM100-120G-2280B-RD |
V-Color | SATA3 | VLM100-240G-2280RGB |
V-Color | SATA3 | VSM100-240G-2280 |
V-Color | SATA3 | VLM100-240G-2280B-RD |
WD | SATA3 | WDS100T1B0B-00AS40 |
WD | SATA3 | WDS240G1G0B-00RC30 |
WD | PCIe3 x4 | WDS256G1X0C-00ENX0 (NVME) |
WD | PCIe3 x4 | WDS512G1X0C-00ENX0 (NVME) |
--- | --- | --- |
2.10 M.2_SSD (NGFF) Module Installation Guide (M2_3)
The M.2, also known as the Next Generation Form Factor (NGFF), is a small size
and versatile card edge connector that aims to replace mPCIe and mSATA. The
Ultra M.2
Socket (M2_3) supports M Key type 2260/2280/22110 M.2 SATA3 6.0 Gb/s module
and M.2 PCI Express module up to Gen3 x4 (32 Gb/s).
- If M2_3 is occupied by a SATA-type M.2 device, SATA3_2 will be disabled.
I nstalling the M.2_SSD (NGFF) Module
Step 1
Prepare a M.2_SSD (NGFF) module and the screw.
Step 2
Depending on the PCB type and length of your M.2_SSD (NGFF) module, find the
corresponding nut location to be used.
No. | 1 | 2 | 3 |
---|---|---|---|
Nut Location | A | B | C |
PCB Length | 6cm | 8cm | 11cm |
Module Type | Ty pe 2260 | Ty pe 2280 Ty | Ty pe 22110 |
Step 3
Move the standoff based on the module type and length. The standoff is placed
at the nut location B by default. Skip Step 3 and 4 and go straight to Step 5
if you are going to use the default nut. Otherwise, release the standoff by
hand.
Step 4
Peel off the yellow protective film on the nut to be used. Hand tighten the
standoff into the desired nut location on the motherboard.
Step 5
Gently insert the M.2 (NGFF) SSD module into the M.2 slot. Please be aware
that the M.2 (NGFF) SSD module only fits in one orientation.
Step 6
Tighten the screw with a screwdriver to secure the module into place. Please
do not overtighten the screwas this might damage the module.
M.2_SSD (NGFF) Module Support List (M2_3)
Vendor | Interface | P/N |
---|---|---|
ADATA | SATA3 | AXNS330E-32GM-B |
ADATA | SATA3 | AXNS381E-128GM-B |
ADATA | SATA3 | AXNS381E-256GM-B |
ADATA | SATA3 | ASU800NS38-256GT-C |
ADATA | SATA3 | ASU800NS38-512GT-C |
ADATA | PCIe3 x4 | ASX7000NP-128GT-C |
ADATA | PCIe3 x4 | ASX8000NP-256GM-C |
DATA | PCIe3 x4 | ASX7000NP-256GT-C |
DATA | PCIe3 x4 | ASX8000NP-512GM-C |
ADATA | PCIe3 x4 | ASX7000NP-512GT-C |
Apacer | PCIe3 x4 | AP240GZ280 |
Corsair | SATA3 | CSSD-F240GBMP500 |
Corsair | SATA3 | CT120M500SSD4 |
Corsair | SATA3 | CT240M500SSD4 |
Intel | PCIe3 x4 | Intel SSDSCKGW080A401/80G |
Intel | PCIe3 x4 | SSDPEKKF256G7 |
Intel | SATA3 | SSDPEKKF512G7 |
Kingston | PCIe3 x4 | SM2280S3 |
Kingston | PCIe2 x4 S | SKC1000/480G |
Kingston | PCIe3 x4 | SH2280S3/480G |
OCZ | PCIe3 x4 | RVD400 -M2280-512G (NVME) |
PATR IOT | PCIe3 x4 | PH240GPM280SSDR NVME |
Plextor | PCIe3 x4 | PX-128M8PeG |
Plextor | PCIe3 x4 | PX-1TM8PeG |
Plextor | PCIe3 x4 | PX-256M8PeG |
Plextor | PCIe | PX-512M8PeG |
Plextor | PCIe | PX-G256M6e |
Plextor | PCIe3 x4 | PX-G512M6e |
Samsung | PCIe3 x4 | SM961 MZVPW128HEGM (NVM) |
Samsung | PCIe3 x4 | PM961 MZVLW128HEGR (NVME) |
Samsung | PCIe3 x4 | 960 EVO (MZ-V6E250) (NVME) |
Samsung | PCIe3 x4 | 960 EVO (MZ-V6E250BW) (NVME) |
Samsung | PCIe3 x4 | SM951 (NVME) |
Samsung | PCIe3 x4 | SM951 (MZHPV256HDGL) |
Samsung | PCIe3 x4 | SM951 (MZHPV512HDGL) |
Samsung | PCIe | SM951 (NVME) |
Samsung | PCIe | XP941-512G (MZHPU512HCGL) |
SanDisk | SATA3 | SD6PP4M-128G |
SanDisk | SATA3 | SD6PP4M-256G |
Team | SATA3 | TM4PS4128GMC105 |
Team | SATA3 | TM4PS4256GMC105 |
Team | PCIe3 x4 | TM8PS4128GMC105 |
Team | PCIe3 x4 | TM8PS4256GMC105 |
TEAM | SATA3 | TM8FP2240G0C101 |
TEAM | SATA3 | TM8FP2480GC110 |
Transcend | SATA3 | TS256GMTS400 |
Transcend | SATA3 | TS512GMTS600 |
Transcend | SATA3 | TS512GMTS800 |
V-Color | SATA3 | VLM100-120G-2280B-RD |
V-Color | SATA3 | VLM100-240G-2280RGB |
V-Color | SATA3 | VSM100-240G-2280 |
V-Color | SATA3 | VLM100-240G-2280B-RD |
WD | SATA3 | WDS100T1B0B-00AS40 |
WD | SATA3 | WDS240G1G0B-00RC30 |
WD | PCIe3 x4 | WDS256G1X0C-00ENX0 (NVME) |
WD | PCIe3 x4 | WDS512G1X0C-00ENX0 (NVME) |
--- | --- | --- |
For the latest updates of M.2_SSD (NFGG) module support list, please visit our website for details: http://www.asrock.com
ASRock Polychrome SYNC
ASRock Polychrome SYNC is a lighting control utility specifically designed for unique individuals with sophisticated tastes to build their own stylish colorful lighting system. Simply by connecting the LED strip, you can customize various lighting schemes and patterns, including Static, Breathing, Strobe, Cycling, Music, Wave and more. Connecting the LED Strip Connect your RGB LED strips to the RGB LED Headers (RGB_LED1 / RGB_LED2) on the motherboard.
- Never install the RGB LED cable in the wrong orientation; otherwise, the cable may be damaged.
- Before installing or removing your RGB LED cable, please power off your system and unplug the power cord from the power supply. Failure to do so may cause damages to motherboard components.
1. Please note that the RGB LED strips do not come with the package.
2. The RGB LED header supports standard 5050 RGB LED strip (12V/G/R/B), with a maximum power rating of 3A (12V) and length within 2 meters.
Connecting the Addressable RGB LED Strip
Connect your Addressable RGB LED strips to the Addressable LED Headers
(ADDR_LED1 /
ADDR_LED2) on the motherboard.
- Never install the RGB LED cable in the wrong orientation; otherwise, the cable may be damaged.
- Before installing or removing your RGB LED cable, please power off your system and unplug the power cord from the power supply. Failure to do so may cause damages to motherboard components.
1. Please note that the RGB LED strips do not come with the package.
2. The RGB LED header supports WS2812B addressable RGB LED strip (5V/Data/
GND), with a maximum power rating of 3A (5V) and length within 2 meters.
ASRock Polychrome SYNC Utility
Now you can adjust the RGB LED color through the ASRock Polychrome SYNC
Utility.
Download this utility from the ASRock Live Update & APP Shop and start
coloring your PC style your way!
Contact Information
If you need to contact ASRock or want to know more about ASRock, you’re
welcome to visit ASRock’s website at
http://www.asrock.com; or you may contact your dealer
for further information. For technical questions, please submit a support
request form at https://event.asrock.com/tsd.asp
ASRock Incorporation
2F., No.37, Sec. 2, Jhongyang S. Rd., Beitou District, Taipei City 112, Taiwan
(R.O.C.) ASRock EUROPE B.V. Bijsterhuizen 11-11 6546 AR Nijmegen The
Netherlands
Phone: +31-24-345-44-33
Fax: +31-24-345-44-38
ASRock America, Inc.
13848 Magnolia Ave, Chino, CA91710 U.S.A.
Phone: +1-909-590-8308
Fax: +1-909-590-1026
DECLARATION OF CONFORMITY
Per FCC Part 2 Section 2.1077(a)
Responsible Party Name: ASRock Incorporation Address: 13848 Magnolia Ave,
Chino, CA91710
+1-909-590-8308/+1-909-590-1026
Phone/fax: y declares that the product
Product Name: Motherboard
Model Number: H570 Steel Legend
informs to the following specifications: FCC Part 15, Subpart B, Unintentional
Radiators
Supplementary Information: is device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions: (1) is device may not
cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
Representative Person’s Name: James
Signature :
Date : May 12, 2017
EU Declaration of Conformity
For the following equipment:
Motherboard
(Product Name)
H570 Steel Legend / ASRock
(Model Designation / Trade Name)
ASRock Incorporation
(Manufacturer Name)
2F., No.37, Sec. 2, Jhongyang S. Rd., Beitou District, Taipei City 112,
Taiwan (R.O.C.)
(Manufacturer Address)
EMC —Directive 2014/30/EU (from April 20th, 2016)
EN 55022:2010/AC:2011 Class B
EN 55024:2010/A1:2015
EN 55032:2012+AC:2013 Class B EN 61000-3-3:2013
EN 61000-3-2:2014
LVD —Directive 2014/35/EU (from April 20th, 2016)
EN 60950-1 : 2011+ A2: 2013 EN 60950-1 : 2006/A12: 2011
RoHS — Directive 2011/65/EU CE marking
(EU conformity marking)
ASRock EUROPE B.V.
(Company Name)
Bijsterhuizen 1111 6546 AR Nijmegen The Netherlands
(Company Address)
Person responsible for making this declaration:
(Name, Surname)
A.V.P
(Position / Title)
February 5, 2021
(Date)
P/N: 15G062292000AK V1.0
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>