LG 49UN7000PUB LED TV Owner’s Manual

: June 16, 2024
: LG

Table of Contents

LG 49UN7000PUB LED TV
Specifications
Product Usage Instructions
Important Safety Instruction
Preparing
Optional Extras
FAQs
Registering Magic Remote Control User Guide
Generated Sound
WALL OR CEILING MOUNT YOUR TELEVISION
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

LG 49UN7000PUB LED TV

Specifications

Model: 43UN7300PUF, 43UN7300PUC, 43UN7300AUD, 43UN7300PUD,
43UN7100PUA, 43UN7000PUB, 43UN6950ZUA, 43UN6951ZUA, 49UN7300PUC,
49UN7300PUF, 49UN7300AUD, 49UN7300PUB, 49UN7100PUA, 49UN7000PUB,
50UN8050PUD, 50UN8000PUB, 50UN7300PUF, 50UN7300PUC, 50UN7300AUD,
50UN7300PUB, 50UN7000PUC, 50UN6950ZUF, 50UN6951ZUF, 55UN8050PUD,
55UN8000PUB, 55UN7300PUF, 55UN7300PUC, 55UN7300AUD, 55UN7300PUB,
55UN7310PUC, 55UN7100PUA, 55UN7000PUB, 55UN6950ZUA, 55UN6951ZUA,
60UN7300PUA, 60UN7310PUA, 60UN7000PUB, 60UN6950ZUA, 60UN6951ZUA,
65UN8500PUI, 65UN8500AUJ, 65UN8050PUD, 65UN8000PUB, 65UN7300PUF,
65UN7300PUC, 65UN7300AUD, 65UN7300PUB, 65UN7310PUC, 65UN7100PUA,
65UN6950ZUA, 65UN6951ZUA, 70UN7370PUC, 70UN7370AUD, 70UN7370PUB,
70UN7100PUA, 70UN7070PUA, 75UN8570PUC, 75UN7370PUE, 75UN8000PUB,
75UN8570AUD, 75UN7370AUH, 75UN7370PUB, 75UN7100PUD, 75UN7070PUC,
75UN6950ZUD, 75UN6951ZUD, 82UN8570PUC, 82UN8570PUB, 82UN8570AUD,
86UN8570PUC, 86UN8570PUB, 86UN8570AUD
LED TV with LCD screen and LED backlights

Product Usage Instructions

Safety Instructions
Before operating your set, please read and follow these safety instructions:

If the power cord or plug is damaged, or if liquid has been spilled or objects have fallen into the apparatus, do not operate it and contact customer service.
If the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped, do not use it and contact customer service.
In case of an emergency, the power plug must remain readily accessible.

Important Safety Instruction

By using this product, you agree that all disputes between you and LG arising out of or relating in any way to this product shall be resolved exclusively through binding arbitration on an individual basis. The terms of the arbitration agreement, including details on the procedure for resolving disputes, are available at www.lg.com/us/arbitration (USA) or www.lg.com/ca_en/arbitration (Canada).

Preparing

Before using the product, make sure to do the following:

Check for any optional extras that can enhance your experience.

Optional Extras

The following optional extras are available:

A – Arrow Key / Right Key
< – Arrow Key / Left Key
Power
Mute
Input
SLEEP
TV, TV/RAD
– Number Key 0 – 9
Q.View / Flashback
FAV (Favorite Channel)
Text (Teletext)
T. Opt (Teletext Option)
Return (BACK)
AV (Audio / Video) Mode
Caption/Subtitle
V (Arrow Key / Cursor Down)
My Apps
Menu / Settings
OK / Enter
Q.Menu
List, –
PICTURE
SOUND

FAQs

Q: What should I do if the power cord or plug is damaged?
A: If the power cord or plug is damaged, do not operate the apparatus and contact customer service.

Q: What should I do if water or another substance enters the product?
A: If water or another substance enters the product, immediately contact your local customer service.

Q: What should I do if the product has been damaged?
A: If the product has been damaged, do not use it and contact customer service.

LG LED TV applies LCD screen with LED backlights.
Please read this manual carefully before operating your set and retain it for future reference.

8

ENGLISH _Index

· IfyouconnectagamingdevicetotheTV,usethecablesupplied withthegamingdevice.
· Refertotheexternalequipment’smanualforoperating instructions.
· InPCmode,theremaybenoiseassociatedwiththeresolution, verticalpattern,contrastorbrightness.Ifnoiseispresent,change thePCoutputtoanotherresolution,changetherefreshrateto anotherrateoradjustthebrightnessandcontrastonthe[Picture] menuuntilthepictureisclear.Dependinguponthegraphicscard, someresolutionsettingsmaynotallowtheimagetobepositioned onthescreenproperly.
· SomeUSBHubsmaynotwork.IfaUSBdeviceconnectedthrough aUSBHubisnotdetected,connectitdirectlytotheUSBporton theTV.
· WhenconnectingviaawiredLAN,itisrecommendedtouseaCAT 7cable.
· TheTVmaybecapableofoperatingwithoutaset-top-boxfroma multichannelvideoprogrammingdistributor(MVPD).

Using Button
YoucansimplyoperatetheTVfunctions,usingthebutton.
Basic functions

Remote RS-232C setup
ToobtaintheRS-232Cexternalcontrolsetupinformation,please visitwww.lg.com.Downloadandreadthemanual,(Dependingupon model).
· Donotdroptheproductorletitfalloverwhenconnecting externaldevices.Otherwise,thismayresultininjuryor damagetotheproduct.
· Whenconnectingexternaldevicessuchasvideogame consoles,makesuretheconnectingcablesarelong enough.Otherwise,theproductmayfallover,whichmay causeinjuryordamagetheproduct.

PowerOn(Press) PowerOff1(PressandHold) MenuControl(Press2) MenuSelection(PressandHold3) 1 Allrunningappswillclose. 2 Youcanaccessandadjustthemenubypressingthebuttonwhen TVison. 3 Youcanusethefunctionwhenyouaccessmenucontrol.
Adjusting the menu
WhentheTVisturnedon,pressthe buttononetime.Youcanadjust theMenuitemsusingthebutton.
Turnsthepoweroff. Changestheinputsource. Adjuststhevolumelevel. Scrollsthroughthesavedchannels.

9

ENGLISH _Index

Using Remote Control

To use the button, press and hold for more than 1 second.

(Dependinguponmodel) Thedescriptionsinthismanualarebasedonthebuttonsontheremote control.PleasereadthismanualcarefullyandusetheTVcorrectly. Toinstallbatteries,openthebatterycover,replacebatteries(1.5VAAA) matchingthe and endstothelabelinsidethecompartment, andclosethebatterycover.Toremovethebatteries,performthe installationactionsinreverse.Thisremoteusesinfraredlight.Whenin use,itshouldbepointedinthedirectionoftheTV’sremotesensor.
Makesuretopointtheremotecontroltowardtheremotecontrolsensor ontheTV.

1

(POWER)TurnstheTVonoroff. ReturnstothelastTVchannel. (SEARCH)Checkforrecommendedcontent.(Some recommendedservicesmaynotbeavailableinsomecountries.) Showsthesearchmode.
Activatesordeactivatesthesubtitles.
(Q. Settings)AccessestheQuickSettings. (INPUT)Changestheinputsource. Number buttonEntersnumbers. Accessesthe[QuickHelp]. (DASH)Insertsa betweennumberssuchas2-1and2-2.
Accessesthesavedchannelslist. (MORE ACTIONS)Displaysmoreremotecontrolfunctions.
EditsQUICKACCESS.
– QUICKACCESSisafeaturethatallowsyoutoenteraspecifiedapp orLiveTVdirectlybypressingandholdingthenumberbuttons. Adjuststhevolumelevel. Accessesyourfavoritechannellist. Displaystheprogrameventaccordingtotimescheduler.
(MUTE)Mutesallsounds.
(MUTE)Accessesthe[Accessibility]menu. Scrollsthroughthesavedchannels. Movestothepreviousornextscreen. 1 Streaming Service buttonsConnectstotheVideoStreaming Service. (HOME)AccessestheHomemenu.
(HOME)Showstheprevioushistory. Returnstothepreviousscreen. Clearson- screendisplaysandreturnstolastinputviewing. Navigation button(up/down/left/right)Scrollsthroughmenus oroptions. (OK)Selectsmenusoroptionsandconfirmsyourinput.
Showsinformationonthecurrentprogram. EnablesSAP(SecondaryAudioProgram)Feature. Startstorecord.(OnlyTimeMachineReadysupportedmodel)
(Control buttons)Controlbuttonsformedia contents.
, , , Theseaccessspecialfunctionsinsomemenus.

(Somebuttonsandservicesmaynotbeprovideddependingupon modelsorregions.)

10

ENGLISH _Index

Using Magic Remote Control To use the button, press and hold for more than 1 second.

(Dependinguponmodel)
Thedescriptionsinthismanualarebasedonthebuttonsontheremote control.PleasereadthismanualcarefullyandusetheTVcorrectly.
Whenthemessage[Magicremotebatteryislow.Pleasechangethe battery.]isdisplayed,replacethebatteries.
Toinstallbatteries,openthebatterycover,replacebatteries(1.5VAA) matchingthe and endstothelabelinsidethecompartment, andclosethebatterycover.Besuretopointthemagicremotetoward theremotecontrolsensorontheTV.Toremovethebatteries,perform theinstallationactionsinreverse.Thisremoteusesinfraredlight.When inuse,itshouldbepointedinthedirectionoftheTV’sremotesensor.

1

(Somebuttonsandservicesmaynotbeprovideddependingupon modelsorregions.)

(POWER)TurnstheTVonoroff.
(STB POWER)Youcanturnyourset-topboxonoroffbyadding theset- topboxtotheuniversalremotecontrolforyourTV. Number buttonsEntersnumbers.
Accessesthe[QuickHelp]. (DASH)Insertsa betweennumberssuchas2-1and2-2.
Accessesthesavedchannelslist. (MORE ACTIONS)Displaysmoreremotecontrolfunctions.
EditsQUICKACCESS.
– QUICKACCESSisafeaturethatallowsyoutoenteraspecifiedapp orLiveTVdirectlybypressingandholdingthenumberbuttons. SAP(SecondaryAudioProgram)Featurecanalsobe
enabledbypressingthe button. Adjuststhevolumelevel.
(MUTE)Mutesallsounds.
(MUTE)Accessesthe[Accessibility]menu. Scrollsthroughthesavedchannels.
(Voice recognition)Networkconnectionisrequiredtousethe voicerecognitionfunction. Checkforrecommendedcontent.(Somerecommendedservicesmay notbeavailableinsomecountries.)
(Voice recognition)Speakwhilepressingandholdingthe buttontousethevoicerecognitionfeature.
(HOME)AccessestheHomemenu.
(HOME)Showstheprevioushistory.
(Q. Settings)AccessestheQuickSettings.
(Q. Settings)Displaysthe[AllSettings]menu.
Wheel (OK)PressthecenteroftheWheelbuttontoselecta menu.Youcanchangechannelsbyusingthewheelbutton.
(up/down/left/right)Presstheup,down,leftorright buttontoscrollthemenu.Ifyoupress buttonswhilethe pointerisinuse,thepointerwilldisappearfromthescreenandMagic Remotewilloperatelikeageneralremotecontrol.Todisplaythe pointeronthescreenagain,shakeMagicRemotetotheleftandright.
(BACK)Returnstothepreviousscreen. (BACK)Clearson- screendisplaysandreturnstolastinput viewing.
Displaystheprogrameventaccordingtotimescheduler. 1 Streaming Service buttonsConnectstotheVideoStreaming Service.
(INPUT)Changestheinputsource.
(INPUT)Accessesthe[HomeDashboard]. , , , Theseaccessspecialfunctionsinsomemenus. , (Control buttons)Controlsmediacontents.

11

ENGLISH _Index

Registering Magic Remote Control User Guide

How to register the Magic Remote Control
TousetheMagicRemote,firstpairitwithyourTV.
1 PutbatteriesintotheMagicRemoteandturntheTVon. 2 PointtheMagicRemoteatyourTVandpressthe Wheel (OK)on
theremotecontrol. * IftheTVfailstoregistertheMagicRemote,tryagainafterturning
theTVoffandbackon.
How to deregister the Magic Remote Control
Pressthe (BACK)and (HOME)buttonsatthesametime,for fiveseconds,tounpairtheMagicRemotewithyourTV.

Pressandholdthe buttonformorethan5secondstodisconnect andre-registertheMagicRemoteatthesametime. · Donotmixnewbatterieswitholdbatteries.Thismay causethebatteriestooverheatandleak. · Failuretomatchthecorrectpolaritiesofthebattery maycausethebatterytoburstorleak,resultinginfire, personalinjury,orambientpollution. · Thisapparatususesbatteries.Inyourcommunitythere mightberegulationsthatrequireyoutodisposeofthese batteriesproperlyduetoenvironmentalconsiderations. Pleasecontactyourlocalauthoritiesfordisposalor recyclinginformation. · Batteriesinsideorinsidetheproductshallnotbeexposed toexcessiveheatsuchassunshine,fireorthelike.

FormoreinformationaboutthisTV,readtheUSERGUIDEembeddedin theproduct.
· ToopentheUSERGUIDE [Support] [UserGuide] Troubleshooting
CannotcontroltheTVwiththeremotecontrol. · Checkifanythingsuchastapehasbeenplacedoverthereceiver. · Checkifthereisanyobstaclebetweentheproductandtheremote control. · Replacethebatterieswithnewfreshones.
Noimagedisplayandnosoundisproduced. · Checkiftheproductisturnedon. · Checkifthepowercordisconnectedtoawalloutlet. · Checkifthereisaprobleminthewalloutletbyconnectingother products.
TheTVturnsoffsuddenly. · Checkthepowercontrolsettings.Thepowersupplymaybe interrupted. · Checkiftheauto-offfunctionisactivatedinthesettingsmenu. · IfthereisnosignalwhiletheTVison,theTVwillturnoff automaticallyafter15minutesofinactivity.

12

ENGLISH _Index

Abnormal Display
· IftheTVfeelscoldtothetouch,theremaybeasmallflickerwhen itisturnedon.Thisisnormal;thereisnothingwrongwithTV. Someminutedotdefectsmaybevisibleonthescreen,appearing astinyred,green,orbluespots.However,theyhavenoadverse effectontheTV’sperformance.AvoidtouchingtheLCDscreenor holdingyourfinger(s)againstitforlongperiodsoftime.Doingso mayproducesometemporarydistortioneffectsonthescreen.
· Thispanelisanadvancedproductthatcontainsmillionsofpixels. Inaveryfewcases,youcouldseefinedotsonthescreenwhile you’reviewingtheTV.Thosedotsaredeactivatedpixelsanddonot affecttheperformanceandreliabilityoftheTV.
· Displayingastillimageforaprolongedperiodoftimemaycause animagesticking.AvoiddisplayingafixedimageontheTVscreen foraextendedlengthoftime.

Generated Sound

· Cracking noiseAcrackingnoisethatoccurswhenwatchingor turningofftheTVisgeneratedbyplasticthermalcontractiondue totemperatureandhumidity.Thisnoiseiscommonforproducts wherethermaldeformationisrequired.
· Electrical circuit humming/panel buzzingAlowlevelnoise isgeneratedfromahigh- speedswitchingcircuit,whichsuppliesa largeamountofcurrenttooperateaproduct.Itvariesdepending upontheproduct.Thisgeneratedsounddoesnotaffectthe performanceandreliabilityoftheproduct.

· Whencleaningtheproduct,becarefulnottoallowany liquidorforeignobjectstoenterthegapbetweenthe upper,leftorrightsideofthepanelandtheguidepanel, (Dependinguponmodel).
· Makesuretowringanyexcesswaterorcleanerfromthe cloth.
· DonotspraywaterorcleanerdirectlyontotheTVscreen. · Makesuretosprayjustenoughofwaterorcleanerontoa
dryclothtowipethescreen.

13

ENGLISH _Index

Specifications

Productspecificationsmaybechangedwithoutpriornoticeduetoupgradeofproductfunctions.
EstimatedyearlyenergyconsumptionindicatedontheFTClabelismeasuredinaccordancewiththeTestProceduresforTelevisionSets(USAonly).
Theactualenergyconsumptiondependsontheusageenvironment(Thecontentwatched,TVsettings,etc.).
· Forinformationofthepowersupplyandpowerconsumption,refertothelabelattachedtotheproduct. – ThetypicalpowerconsumptionismeasuredinaccordancewithIEC62087oreachcountry’senergyregulations.

Onsomemodels,thelabelisinsidetheexternaldeviceconnectionterminalcover. * Dependinguponthemodelorcountry,thetypicalpowerconsumptionmaynotbeonlabel.

CHILD SAFETY:
PROPER TELEVISION PLACEMENT MATTERS
THE CONSUMER ELECTRONICS INDUSTRY CARES
· Manufacturers, retailers and the rest of the consumer electronics industry are committed to making home entertainment safe and enjoyable. · As you enjoy your television, please note that all televisions new and old- must be supported on proper stands or installed according to the manufacturer’s recommendations. Televisions that are inappropriately situated on dressers, bookcases, shelves, desks, speakers, chests, carts, etc., may fall over, resulting in injury.

TUNE IN TO SAFETY
· ALWAYS follow the manufacturer’s recommendations for the safe installation of your television. · ALWAYS read and follow all instructions for proper use of your television. · NEVER allow children to climb on or play on the television or the furniture on which the television is placed. · NEVER place the television on furniture that can easily be used as steps, such as a chest of drawers. · ALWAYS install the television where it cannot be pushed, pulled over or knocked down. · ALWAYS route cords and cables connected to the television so that they cannot be tripped over, pulled or grabbed.

WALL OR CEILING MOUNT YOUR TELEVISION

· ALWAYS contact your retailer about professional installation if you have any doubts about your ability to safely mount your television. · ALWAYS use a mount that has been recommended by the television manufacturer and has a safety certification by an independent laboratory (such as UL, CSA, ETL). · ALWAYS follow all instructions supplied by the television and mount manufacturers. · ALWAYS make sure that the wall or ceiling where you are mounting the television is appropriate. Some mounts are not designed to be mounted to walls and ceilings with steel studs or cinder block construction. If you are unsure, contact a professional installer. · Televisions can be heavy. A minimum of two people is required for a wall or ceiling mount installation.

MOVING AN OLDER TELEVISION TO A NEW PLACE IN YOUR HOME
· Many new television buyers move their older CRT televisions into a secondary room after the purchase of a flat-panel television. Special care should be made in the placement of older CRT televisions. · ALWAYS place your older CRT television on furniture that is sturdy and appropriate for its size and weight. · NEVER place your older CRT television on a dresser where children may be tempted to use the drawers to climb. · ALWAYS make sure your older CRT television does not hang over the edge of your furniture.
CE.org/safety

19

Supplier`s Declaration of Conformity

Trade Name Responsible Party
Address

LG
LG Electronics USA, Inc.
1000 Sylvan Ave Englewood Cliffs, NJ 07632

Telephone

(201)266-2215

The model and serial number of the product are located on the back and on one side of the product. Record them below in case you ever need service.
Model Serial No.

LG Customer Information Center For inquires or comments, visit www.lg.com or call;

1-800-243-0000 1-888-865-3026 1-888-542-2623

USA, Consumer User USA, Commercial User CANADA

Register your product Online! www.lg.com

OWNER’S MANUAL
EXTERNAL CONTROL DEVICE SETUP
Please read this manual carefully before operating the set and retain it for future reference.
www.lg.com P/NO : MFL71445401 (1901-REV00)

ENEGNLGISH

2 KEY CODES

KEY CODES
· This feature is not available for all models.

Code (Hexa)

Function

00 CH +, PR +

01 CH -, PR –

02 Volume +

03 Volume –

06 > (Arrow Key / Right Key)

07 < (Arrow Key / Left Key)

08 Power

09 Mute

0B Input

0E SLEEP

0F TV, TV/RAD

10 – 19 * Number Key 0 – 9

1A Q.View / Flashback

1E FAV (Favorite Channel)

20 Text (Teletext)

21 T. Opt (Teletext Option)

28 Return (BACK)

30 AV (Audio / Video) Mode

39 Caption/Subtitle

40 (Arrow Key / Cursor Up)

41

V (Arrow Key / Cursor Down)

42 My Apps

43 Menu / Settings

44 OK / Enter

45 Q.Menu

4C List, –

4D PICTURE

52 SOUND

Note
R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button
R/C Button
R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button

Code (Hexa)

Function

53 List

5B Exit

60 PIP(AD)

61 Blue

63 Yellow

71 Green

72 Red

79 Ratio / Aspect Ratio

91 AD (Audio Description)

9E LIVE MENU

7A User Guide

7C Smart / Home

7E SIMPLINK

8E (Forward)

8F (Rewind)

AA Info

AB Program Guide

B0 (Play)

B1 (Stop / File List)

B5 RECENT

BA

(Freeze / Slow Play / Pause)

BB Soccer

BD (REC)

DC 3D

99 AutoConfig

9F App / *

9B TV / PC

Note
R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button
R/C Button
R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button

Key code 4C (0x4C) is available on ATSC/ISDB models which use major/minor channel. (For South Korea, Japan, North America, Latin America except Colombia models)

ENEGNLGISH

EXTERNAL CONTROL DEVICE SETUP 3

EXTERNAL CONTROL DEVICE SETUP
· Image shown may differ from your TV.
Connect the USB to Serial(RS-232C) converter/RS-232C(Serial) input jack to an external control device (such as a computer or an A/V control system) to control the product’s functions externally.
Note: The type of control port on the TV can be different between model series.

Please be advised that not all models support this type of connectivity. * Cable is not provided.
USB to Serial(RS-232C) converter with USB Cable
USB Type

(PC)

(TV)

USB IN

· LGTV supports PL2303 chip-based (Vendor ID : 0x0557, Product ID : 0x2008) USB to serial(RS-232C) converter which is not made nor provided by LG.
· It can be purchased from computer stores that carry accessories for IT support professionals.
RS-232C(Serial) With RS-232C(Serial) Cable
DE9 (D-Sub 9pin) Type · You need to purchase the RS-232C (DE9, D-Sub 9pin female-to-female type) to RS-232C(Serial) cable
required for the connection between the PC and the TV, which is specified in the manual.

(PC)

RS-232C IN
(CONTROL & SERVICE)

(TV)

The connection interface may differ from your TV.

ENEGNLGISH

4 EXTERNAL CONTROL DEVICE SETUP

Phone jack Type
· You need to purchase the phone-jack to RS-232 cable required for the connection between the PC and the TV, which is specified in the manual.

For other models, connect to the USB port. * The connection interface may differ from your TV.

SERVICE ONLY

1 3

(PC)

(TV)

2

– or

(PC)

1 3
2

RS-232C IN
(CONTROL & SERVICE)

(TV)

Customer Computer

1

5

RS-232C configurations
3-Wire Configurations(Not standard)

RXD

PC 2

TV 2 TXD

TXD 3 GND 5

1 RXD 3 GND

6

9

RS-232C (Serial port)

RXD TXD GND

OR 3 2 5
D-Sub 9

2 1 3 Phone

TXD RXD GND

Set ID For Set ID number, see “Real Data Mapping” on p.6

1. Press SETTINGS to access the main menus. 2. Press the Navigation buttons to scroll to (*General About this TV or OPTION) and press OK. 3. Press the Navigation buttons to scroll to SET ID and press OK. 4. Scroll left or right to select a set ID number and select CLOSE. The adjustment range is 1-99. 5. When you are finished, press EXIT.

(Depending on model)

ENEGNLGISH

EXTERNAL CONTROL DEVICE SETUP 5

Communication Parameters

· Baud rate : 9600 bps (UART) · Data length : 8 bits · Parity : None
Command reference list
(Depending on model)

· Stop bit : 1 bit · Communication code : ASCII code · Use a crossed (reverse) cable.

COMMAND1

COMMAND2

DATA (Hexadecimal)

COMMAND1

COMMAND2

DATA (Hexadecimal)

01. Power* k

02. Aspect Ratio

k

03. Screen Mute

k

04. Volume Mute

k

05. Volume Control

k

06. Contrast k

07. Brightness

k

08. Color/ Colour

k

09. Tint

k

10. Sharpness

k

11. OSD Select

k

12. Remote Control Lock k Mode

13. Treble k

a

00 to 01

15. Balance k

t

16. Color

c

(p.7)

(Colour)

x

u

Temperature

17. ISM

d

(p.7)

Method (Only j

p

Plasma TV)

e

00 to 01

18. Equalizer j

v

f

00 to 64

19. Energy Saving

j

q

g

00 to 64

20. Tune Command

m

a

21. Channel m

b

h

00 to 64

(Programme)

Add/Del(Skip)

i

00 to 64

22. Key

m

c

23. Control m

g

j

00 to 64

Backlight, Control Panel

Light

k

00 to 32

24. Input

x

select (Main)

b

l

00 to 01

25. 3D (Only x 3D models)

t

26. Extended x

v

m

00 to 01

3D (Only 3D

models)

27. Auto

j

u

r

00 to 64

Configure

00 to 64 00 to 64
(p.8) (p.9) 00 to 05 (p.9) 00 to 01
Key Codes 00 to 64
(p.11) (p.11) (p.12)
(p.12)

14. Bass

k

s

00 to 64

Note: During playing or recording media, all commands except Power (ka) and Key (mc) are not executed and treated as NG. With RS232C cable, TV can communicate “ka command” in power-on or power-off status. but with USB-to-Serial converter cable, the command works only if TV is on.

ENEGNLGISH

6 EXTERNAL CONTROL DEVICE SETUP

Transmission / Receiving Protocol

Transmission [Command1][Command2][ ][Set ID][ ][Data][Cr] [Command 1] : First command to control the TV. (j, k, m or x)

[Command 2] : Second command to control the TV. [Set ID]

: You can adjust the [Set ID] to choose desired monitor ID number in option menu.

Adjustment range in TV is 1 to 99. If [Set ID] value is selected to `0′, every connected set

can be controlled.

[Set ID] is indicated as decimal (1 to 99) on menu and as Hexadecimal (0x00 to 0x63) on

transmission/receiving protocol.

[DATA]

: To transmit command data (hexadecimal). Transmit `FF’ data to read status of command.

[Cr]

: Carriage Return – ASCII code `0x0D’

[ ]

: Space ASCII code `0x20′

OK Acknowledgement [Command2][ ][Set ID][ ][OK][Data][x] * The set transmits ACK (acknowledgement) based on this format when receiving normal data. At this time, if the data is data read mode, it indicates present status data. If the data is data write mode, it returns the data of the PC computer.

Error Acknowledgement [Command2][ ][Set ID][ ][NG][Data][x] * The set transmits ACK (acknowledgement) based on this format when receiving abnormal data from non-viable functions or communication errors.
Data 00: Illegal Code

Real data mapping (Hexadecimal b Decimal)

When you enter the [data] in hexadecimal, refer to following conversion table. * Channel Tune (ma) Command uses two-byte hexadecimal value([data]) to select channel number.

00 : Step 0 01 : Step 1 (Set ID 1) … 0A : Step 10 (Set ID 10) … 0F : Step 15 (Set ID 15) 10 : Step 16 (Set ID 16) …

32 : Step 50 (Set ID 50) 33 : Step 51 (Set ID 51) … 63 : Step 99 (Set ID 99) … C7 : Step 199 C8 : Step 200 …

FE : Step 254 FF : Step 255 … 01 00 : Step 256 … 27 0E : Step 9998 27 0F : Step 9999 …

ENEGNLGISH

EXTERNAL CONTROL DEVICE SETUP 7

Commands may work differently depending on model and signal.

01. Power (Command: k a) To control Power *On or Off of the set.
Transmission[k][a][ ][Set ID][ ][Data][Cr]

Data 00 : Power Off

01 : *Power On

Ack [a][ ][Set ID][ ][OK/NG][Data][x] To Show TV is Power On or *Off
Transmission [k][a][ ][Set ID][ ][FF][Cr] Ack [a][ ][Set ID][ ][OK][Data][x]

Similarly, if other functions transmit `FF’ data based on this format, Acknowledgement feedback presents status about each function.

Ack [d][ ][Set ID][ ][OK/NG][Data][x] * In case of video mute on only, TV will display On Screen Display(OSD). But, in case of Screen mute on, TV will not display OSD.
04. Volume Mute (Command: k e) To control volume mute on/off.
You can also adjust mute using the MUTE button on remote control. Transmission [k][e][ ][Set ID][ ][Data][Cr] Data 00 : Volume mute on (Volume off)
01 : Volume mute off (Volume on) Ack [e][ ][Set ID][ ][OK/NG][Data][x]

02. Aspect Ratio (Command: k c) (Main Picture Size)
To adjust the screen format. (Main picture format) You can also adjust the screen format using the Aspect Ratio in the Q.MENU. or PICTURE menu.

Transmission [k][c][ ][Set ID][ ][Data][Cr]

Data 01 : Normal screen 07 : 14:9

(4:3)

(Europe, Colombia, Mid-East,

02 : Wide screen Asia except South Korea and

(16:9)

Japan)

04 : Zoom

09 : * Just Scan

05 : Zoom 2

0B : Full Wide

(Latin America

(Europe, Colombia, Mid-

except Colombia East, Asia except South

Only)

Korea and Japan)

06 : Set by Program/ 10 to 1F : Cinema Zoom 1 to 16

Original

0c : 21:9 (Depending on model)

Ack [c][ ][Set ID][ ][OK/NG][Data][x]

Using the PC input, you select either 16:9 or 4:3 screen aspect ratio.
In DTV/HDMI/Component mode (high-definition), Just Scan is available.
Full wide mode may work differently based on model and is supported for DTV fully, and ATV, AV partially.

03. Screen Mute (Command: k d) To select screen mute on/off.
Transmission [k][d][ ][Set ID][ ][Data][Cr] Data 00 : Screen mute off (Picture on) Video mute off
01 : Screen mute on (Picture off) 10 : Video mute on

05. Volume Control (Command: k f) To adjust volume.
You can also adjust volume with the volume buttons on remote control. Transmission [k][f][ ][Set ID][ ][Data][Cr] Data Min : 00 to Max : 64 Ack [f][ ][Set ID][ ][OK/NG][Data][x] 06. Contrast (Command: k g) To adjust screen contrast.
You can also adjust contrast in the PICTURE menu. Transmission [k][g][ ][Set ID][ ][Data][Cr] Data Min : 00 to Max : 64 Ack [g][ ][Set ID][ ][OK/NG][Data][x] 07. Brightness (Command: k h) To adjust screen brightness.
You can also adjust brightness in the PICTURE menu. Transmission [k][h][ ][Set ID][ ][Data][Cr] Data Min : 00 to Max : 64 Ack [h][ ][Set ID][ ][OK/NG][Data][x]

ENEGNLGISH

8 EXTERNAL CONTROL DEVICE SETUP

08. Color/Colour (Command: k i) To adjust the screen Color(Colour).
You can also adjust colour in the PICTURE menu. Transmission [k][i][ ][Set ID][ ][Data][Cr] Data Min : 00 to Max : 64 Ack [i][ ][Set ID][ ][OK/NG][Data][x] 09. Tint (Command: k j) To adjust the screen tint.
You can also adjust tint in the PICTURE menu. Transmission [k][j][ ][Set ID][ ][Data][Cr] Data Red : 00 to Green : 64 Ack [j][ ][Set ID][ ][OK/NG][Data][x]

10. Sharpness (Command: k k) To adjust the screen sharpness.
You can also adjust sharpness in the PICTURE menu.
Transmission [k][k][ ][Set ID][ ][Data][Cr] Data Min : 00 to Max : 32
Ack [k][ ][Set ID][ ][OK/NG][Data][x]

11. OSD Select (Command: k l) To select OSD (On Screen Display) on/off when
controlling remotely.
Transmission [k][l][ ][Set ID][ ][Data][Cr]

Data 00 : OSD off

01 : OSD on

Ack [l][ ][Set ID][ ][OK/NG][Data][x]

12. Remote control lock mode (Command: k m) To lock the front panel controls on the monitor and
remote control.
Transmission [k][m][ ][Set ID][ ][Data][Cr]

Data 00 : Lock off

01 : Lock on

Ack [m][ ][Set ID][ ][OK/NG][Data][x]

If you are not using the remote control, use this mode. When main power is off & on (plug-off and plug-in, after 20 – 30 seconds), external control lock is released.
In the standby mode (DC off by off timer or ka’,mc’ command), and if key lock is on, TV will not turn on by power on key of IR & Local Key.

13. Treble (Command: k r) To adjust treble.
You can also adjust in the AUDIO menu.
Transmission [k][r][ ][Set ID][ ][Data][Cr] Data Min : 00 to Max : 64
Ack [r][ ][Set ID][ ][OK/NG][Data][x] (Depending on model)
14. Bass (Command: k s) To adjust Bass.
You can also adjust in the AUDIO menu.
Transmission [k][s][ ][Set ID][ ][Data][Cr] Data Min : 00 to Max : 64
Ack [s][ ][Set ID][ ][OK/NG][Data][x] (Depending on model)
15. Balance (Command: k t) To adjust balance.
You can also adjust balance in the AUDIO menu. Transmission [k][t][ ][Set ID][ ][Data][Cr] Data Min : 00 to Max : 64 Ack [t][ ][Set ID][ ][OK/NG][Data][x] 16. Color(Colour) Temperature (Command: x u) To adjust colour temperature. You can also adjust
Color(Colour) Temperature in the PICTURE menu. Transmission [x][u][ ][Set ID][ ][Data][Cr] Data Min : 00 to Max : 64 Ack [u][ ][Set ID][ ][OK/NG][Data][x] 17. ISM Method (Command: j p) (Only Plasma TV) To control the ISM method. You can also adjust
ISM Method in OPTION menu. Transmission [j][p][ ][Set ID][ ][Data][Cr] Data Min : 02: Orbiter
08: Normal 20: Color(Colour) Wash Ack [p][ ][Set ID][ ][OK/NG][Data][x]

ENEGNLGISH

EXTERNAL CONTROL DEVICE SETUP 9

18. Equalizer (Command : j v)

Adjust EQ of the set.

Transmission [j][v][ ][Set ID][ ][Data][Cr]

MSB

LSB

0000000 0

Frequency

Data

7 6 5 Frequency 4 3 2 1 0

Step

0 0 0 1st Band 0 0 0 0 0 0(decimal)

0 0 1 2nd Band 0 0 0 0 1 1(decimal)

0 1 0 3rd Band … … … … …

…

0 1 1 4th Band 1 0 0 1 1 19(decimal)

1 0 0 5th Band 1 0 1 0 1 20(decimal)

Acknowledgement [v][ ][Set ID][ ][OK/NG][Data][x]

It depends on model, and can adjust when sound mode is EQ adjustable value.

19. Energy Saving (Command: j q)
To reduce the power consumption of the TV. You can also adjust Energy Saving in PICTURE menu.
Transmission [j][q][ ][Set ID][ ][Data][Cr] Data 00 : Off 01 : Minimum 02 : Medium 03 : Maximum 04 : Auto (For LCD TV / LED TV) / Intelligent sensor (For PDP TV) 05 : Screen off

(Depending on model)
Ack [q][ ][Set ID][ ][OK/NG][Data][x]

20. Tune Command (Command: m a)

This command may work differently depending on model and signal.
· For Europe, Mid-East, Colombia, Asia except South Korea and Japan Model
Select channel to following physical number.
Transmission [m][a][ ][Set ID][ ][Data 00][ ] [Data 01][ ][Data 02][Cr]
Analog Antenna/Cable
[Data 00][Data 01] Channel Data Data 00 : High byte channel data Data 01 : Low byte channel data
– 00 00 ~ 00 C7 (Decimal : 0 ~ 199)
Data 02 : Input Source (Analog) – 00 : Antenna TV (ATV) – 80 : Cable TV (CATV)
Digital Antenna/Cable/Satellite
[Data 00][Data 01]: Channel Data Data 00 : High Channel data Data 01 : Low Channel data
– 00 00 ~ 27 0F (Decimal: 0 ~ 9999) Data 02 : Input Source (Digital)
– 10 : Antenna TV (DTV) – 20 : Antenna Radio (Radio) – 40 : Satellite TV (SDTV) – 50 : Satellite Radio (S-Radio) – 90 : Cable TV (CADTV) – a0 : Cable Radio (CA-Radio)
Tune Command Examples: 1. Tune to the Analog antenna (PAL) Channel 10.
Set ID = All = 00 Data 00 & 01 = Channel Data is 10 = 00 0a Data 02 = Analog Antenna TV = 00 Result = ma 00 00 0a 00
2. Tune to the digital antenna (DVB-T) Channel 01. Set ID = All = 00 Data 00 & 01 = Channel Data is 1 = 00 01 Data 02 = Digital Antenna TV = 10 Result = ma 00 00 01 10
3. Tune to the satellite (DVB-S) Channel 1000. Set ID = All = 00 Data 00 & 01 = Channel Data is 1000 = 03 E8 Data 02 = Digital Satellite TV = 40 Result = ma 00 03 E8 40
Ack [a][ ][Set ID][ ][OK][Data 00][Data 01] [Data 02][x][a][ ][Set ID][ ][NG][Data 00][x] · For South Korea, North/Latin America except Colombia Model
To tune channel to following physical/major/minor number.
Transmission [m][a][ ][0][ ][Data00][ ][Data01] [ ][Data02][ ][Data03][ ][Data04][ ][Data05][Cr] Digital channels have a Physical, Major, and Minor channel number. The Physical number is the actual digital channel number, the Major is the number that the channel should be mapped to, and the Minor is the sub-channel. Since the ATSC tuner automatically maps the channel from the Major / Minor number, the Physical number is not required when sending a command in Digital.

ENEGNLGISH

10 EXTERNAL CONTROL DEVICE SETUP

Analog Antenna/Cable
Data 00 : Physical Channel Number – Antenna (ATV) : 02~45 (Decimal: 2 ~ 69) – Cable (CATV) : 01, 0E~7D (Decimal : 1, 14~125)
[Data 01 ~ 04]: Major/Minor Channel Number Data 01 & 02: xx (Don’t care) Data 03 & 04: xx (Don’t care) Data 05: Input Source (Analog)
– 00 : Antenna TV (ATV) – 01 : Cable TV (CATV)
Digital Antenna/Cable
Data 00 : xx (Don’t care)
[Data 01][Data 02]: Major Channel Number Data 01 : High byte Channel Data Data 02 : Low byte Channel Data
– 00 01 ~ 27 0F (Decimal: 1 ~ 9999) [Data 03][Data 04]: Minor Channel Number Data 03 : High byte Channel Data Data 04 : Low byte Channel Data
Data 05 : Input Source (Digital) – 02 : Antenna TV (DTV) Use Physical Channel Number – 06 : Cable TV (CADTV) Use Physical Channel Number – 22 : Antenna TV (DTV) Don’t Use Physical Channel Number – 26 : Cable TV (CADTV) – Don’t Use Physical Channel Number – 46 : Cable TV (CADTV) Use Physical/Major Channel Number Only (One Part Channel) – 66 : Cable TV (CADTV) Use Major Channel Number Only (One Part Channel) – 0b : Cable DTV Plus Use Physical Channel Number – 2b : Cable DTV Plus Don’t Use Physical Channel Number – 4b : Cable DTV Plus Use Physical/Major Channel Number Only (One Part Channel) – 6b : Cable DTV Plus Use Major Channel Number Only (One Part Channel)
Two bytes are available for each major and minor channel data, but usually the low byte is used alone (high byte is 0).
Tune Command Examples: 1. Tune to the Analog cable (NTSC) channel 35.
Set ID = All = 00 Data 00 = Channel Data is 35 = 23 Data 01 & 02 = No Major = 00 00 Data 03 & 04 = No Minor = 00 00 Data 05 = Analog Cable TV = 01 Total = ma 00 23 00 00 00 00 01

2. Tune to the digital antenna (ATSC) channel 30-3. Set ID = All = 00 Data 00 = Don’t know Physical = 00 Data 01 & 02 = Major is 30 = 00 1E Data 03 & 04 = Minor is 3 = 00 03 Data 05 = Digital Antenna TV = 22 Total = ma 00 00 00 1E 00 03 22
Ack [a][ ][Set ID][ ][OK][Data 00][Data 01] [Data 02][Data 03][Data 04][Data 05] [x][a][ ][Set ID][ ][NG][Data 00][x] · For Japan Model To tune channel to following physical/major/minor
number.
Transmission [m][a][ ][0][ ][Data00][ ][Data01] [ ][Data02][ ][Data03][ ][Data04][ ][Data05][Cr] * Digital Antenna/Satellite Data 00: xx (Don’t care)
[Data 01][Data 02]: Major Channel Number Data 01: High byte Channel Data Data 02: Low byte Channel Data
– 00 01 ~ 27 0F (Decimal: 1 ~ 9999)
[Data 03][Data 04]: Minor/Branch Channel Number (Don’t care in Satellite)
Data 03: High byte Channel Data Data 04: Low byte Channel Data
Data 05 : Input Source (Digital/Satellite for Japan) – 02 : Antenna TV (DTV) – 42 : Antenna TV (DTV) Use Physical/Major Channel Number Only (One Part Channel) – 62 : Antenna TV (DTV) Use Major Channel Number Only (One Part Channel) – 07 : BS (Broadcasting Satellite) – 08 : CS1 (Communication Satellite 1) – 09 : CS2 (Communication Satellite 2)

Tune Command Examples: 1 Tune to the digital antenna (ISDB-T) channel 17-1.
Set ID = All = 00 Data 00 = Don’t know Physical = 00 Data 01 & 02 = Major is 17 = 00 11 Data 03 & 04 = Minor/Branch is 1 = 00 01 Data 05 = Digital Antenna TV = 02 Total = ma 00 00 00 11 00 01 02

ENEGNLGISH

EXTERNAL CONTROL DEVICE SETUP 11

2. Tune to the BS (ISDB-BS) channel 30. Set ID = All = 00 Data 00 = Don’t know Physical = 00 Data 01 & 02 = Major is 30 = 00 1E Data 03 & 04 = Don’t Care = 00 00 Data 05 = Digital BS TV = 07 Total = ma 00 00 00 1E 00 00 07

This feature is varied based on the model. Ack [a][ ][Set ID][ ][OK][Data 00][Data 01] [Data 02][Data 03][Data 04][Data 05] [x][a][ ][Set ID][ ][NG][Data 00][x] 21. Channel(Programme) Add/Del(Skip) (Command: m b)
To skip current channel(programme) for next time. Transmission [m][b][ ][Set ID][ ][Data][Cr] Data 00 : Del(ATSC,ISDB)/Skip(DVB) 01 : Add
Ack [b][ ][Set ID][ ][OK/NG][Data][x] * Set the saved channel status to del(ATSC, ISDB)/ skip(DVB) or add.
22. Key (Command: m c) To send IR remote key code.
Transmission [m][c][ ][Set ID][ ][Data][Cr] Data Key code – p.2.
Ack [c][ ][Set ID][ ][OK/NG][Data][x] 23. Control Backlight (Command: m g) · For LCD TV / LED TV To control the backlight.
Transmission [m][g][ ][Set ID][ ][Data][Cr] Data Min : 00 to Max : 64
Ack [g][ ][Set ID][ ][OK/NG][Data][x] Control Panel Light (Command: m g)
· For Plasma TV To control the panel light.
Transmission [m][g][ ][Set ID][ ][Data][Cr] Data Min : 00 to Max : 64
Ack [g][ ][Set ID][ ][OK/NG][Data][x]

24. Input select (Command: x b) (Main Picture Input)
To select input source for main picture.
Transmission [x][b][ ][Set ID][ ][Data][Cr]

Data

00 : DTV

01 : CADTV

02 : Satellite DTV

10 : ATV

ISDB-BS (Japan)

03 : ISDB-CS1 (Japan)

04 : ISDB-CS2 (Japan)

11 : CATV

20 : AV or AV1

21 : AV2

40 : Component1 60 : RGB

41 : Component2

90 : HDMI1 92 : HDMI3

91 : HDMI2 93 : HDMI4

Ack [b][ ][Set ID][ ][OK/NG][Data][x]

This function depends on model and signal.

25. 3D(Command: x t) (only 3D models) (Depending on model)
To change 3D mode for TV.
Transmission [x][t][ ][Set ID][ ][Data 00][ ][Data 01] [ ][Data 02][ ][Data 03][Cr] (Depending on model) Data Structure [Data 00] 00 : 3D On
01 : 3D Off 02 : 3D to 2D 03 : 2D to 3D [Data 01] 00 : Top and Bottom 01 : Side by Side 02 : Check Board 03 : Frame Sequential 04 : Column interleaving 05 : Row interleaving [Data 02] 00 : Right to Left 01 : Left to Right [Data 03] 3D Effect(3D Depth): Min : 00 – Max : 14 (transmit by Hexadecimal code)

ENEGNLGISH

12 EXTERNAL CONTROL DEVICE SETUP

[Data 02], [Data 03] functions depend on model and signal.
If [Data 00] is 00 (3D On), [Data 03] has no meaning.
If [Data 00] is 01 (3D off) or 02 (3D to 2D), [Data 01], [Data 02] and [Data 03] have no meaning.
If [Data 00] is 03 (2D to 3D), [Data 01] and [Data 02] have no meaning.
If [Data 00] is 00 (3D On) or 03 (2D to 3D), [Data 03] works when 3D Mode (Genre) is manual only.
All 3D pattern options ([Data 01]) may not be available according to broadcasting/video signal.

[Data 00] 00 01 02 03 [Data 01] O X X X

X : don’t care

[Data 02] O X X O [Data 03] O X X O

Ack [t][ ][Set ID][ ][OK][Data00][Data01][Data02] [Data03][x] [t][ ][Set ID][ ][NG][Data00][x]

26. Extended 3D(Command: x v) (only 3D models) (Depending on model)
To change 3D option for TV.
Transmission [x][v][ ][Set ID][ ][Data 00][ ] [Data 01][Cr] [Data 00] 3D option 00 : 3D Picture Correction 01 : 3D Depth (3D Mode is Manual Only) 02 : 3D Viewpoint 06 : 3D Color Correction 07 : 3D Sound Zooming 08 : Normal Image View 09 : 3D Mode (Genre)

[Data 01] It has own range for each 3D option determined by [Data 00].

When [Data 00] is 00 00 : Right to Left 01 : Left to Right
When [Data 00] is 01, 02 Data Min: 0 – Max: 14 (transmit by Hexadecimal
code) Data value range(0 – 20) converts Viewpoint range (-10 – +10) automatically (Depending on model) This option works when 3D Mode (Genre) is manual
only.
When [Data 00] is 06, 07 00 : Off 01 : On
When [Data 00] is 08 00 : Revert to 3D video from 3D-to-2D converted 2D video 01 : Change 3D video to 2D video, except 2D-to-3D video

If conversion condition doesn’t meet, command is treated as NG.

When [Data 00] is 09
00 : Standard 02 : Cinema 04 : Manual

01 : Sport 03 : Extreme 05 : Auto

Ack [v][ ][Set ID][ ][OK][Data00][Data01][x] [v][ ][Set ID][ ][NG][Data00][x]

27. Auto Configure (Command: j u) (Depending on model)
To adjust picture position and minimize image shaking automatically. It works only in RGB (PC) mode.
Transmission [j][u][ ][Set ID][ ][Data][Cr] Data 01 : To set Auto Configure
Ack [u][ ][Set ID][ ][OK/NG][Data][x]