WESPER WKRV01 Sleep Kit User Guide
- June 6, 2024
- WESPER
Table of Contents
WESPER WKRV01 Sleep Kit
WESPERTM SLEEP KIT | Model #: WKRV01
Safety and Handling
This device has been tested to comply with IEC standards IEC 6061-1, IEC
6061-1-2, and IEC 6061-11. WESPER is an electrical appliance and safety
precautions should always be followed to reduce the risk of burns, fire,
electric shock or injury, including the following precautions:
Wear And Care
For the avoidance of doubt, WHISPER is not a medical device and is not
intended to replace any medical diagnosis or treatment recommended to you by
your physician. When caring for your WESPER, follow these tips: Do not use
cleaners or any liquid to clean your WESPER. Only place on dry surfaces. Do
not place on a surface wet from water or cleaning solvents. Do not place or
store the product in an area subject to excess dust. Do not expose your WESPER
to direct sunlight for extended periods of time. Do not leave your WESPER near
an open flame. Do not place or store the product where it can fall or be
pulled into a tub or sink. If you experience any kind of discomfort or notice
signs of skin irritation where your WESPER touches your skin, please
discontinue use and contact our support team. Do not attempt to disassemble or
service your WESPER yourself. Protect your WESPER from any shocks or impacts.
Do not expose your WESPER to extremely high temperatures above 104° F (40° C)
or low temperatures below 23° F (-5° C). Battery life: 12 hours (150mAH) Use
only a certified USB power adapter (not included). The power supply should be
Limited Power Supply (LPS).
Important Safety Information:
Take the time to read, understand and follow all safety information contained
in this user manual before using your WESPER. Please save these instructions
for future reference.
CAUTION
Contains small parts. Keep out of reach of children. Use this appliance only
for its intended use as described in this manual. Do not operate this device
if it has a damaged cord, plug, cable, or housing.
Batteries Precautions
To reduce the risk of electric shock and to avoid possible risks associated
with hazardous voltage, which if not avoided could result in death or serious
injuries. Read, understand and follow the following safety instructions: This
product contains a lithium-ion battery. Use only the included wireless
charging mat to recharge your patches. Do not attempt to charge the device
using another wireless charging device. There is a risk of explosion if
batteries are not handled in the correct way. The batteries are not designed
to be replaced. Damage inflicted on the battery could cause an explosion
and/or fire. Do not dismantle, open or shred the battery. Do not expose the
battery to heat or fire. Avoid storage in direct sunlight. Do not short-
circuit the battery.
Disposal And Recycling Information
For disposal and recycling of WHISPER, please contact your local recycling
authority. If you have any questions on the matter, please contact our support
team at support@wesper.co.
FCC Declaration of Conformity Compliance statement
FCC ID: includes 2AAQS-ISP1507 or 2AAQS-ISP1807
This equipment complies with Part 15 of the FCC Rules. Operation is subject to
two conditions: (1) This device may not cause harmful interference, and (2)
this device must accept any interference received, including interference that
may cause undesired operation. As defined in Section 2.909 of the FCC Rules,
the responsible party for this device is: Wesper Inc., 234 5th Ave, New York,
NY 10001, USA. Tel #: +1 575-448-2824
FCC Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment and meets the FCC radio frequency (RF) Exposure
Guidelines. End-users must follow the specific operating instructions for
satisfying RF exposure compliance. This transmitter must not be co-located or
operating in conjunction with any other antenna or transmitter. Federal
Communications Commission Radio Frequency Interference Statement This
equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment causes harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Modifications
Wesper is not responsible for any radio interference caused by unauthorized
modifications to this equipment. Changes or modifications not expressly
approved by Wesper could void the user’s authority and warranty to operate the
equipment.
Silicone Adhesives
WESPER’s adhesives are made from medical-grade silicone. Avoid use if you have
any known allergy to silicone. The adhesives have been thoroughly tested and
should not cause skin irritation. However, if skin irritation develops or any
other symptoms occur, discontinue use and contact us. In case of irritation,
wash skin thoroughly with soap and water. Seek medical attention if symptoms
persist. The adhesives should not be used on wounded skin. If eye contact
occurs, hold the eye open and immediately rinse with water for at least 15
minutes. Obtain medical attention if soreness or redness persists.
Customer Service Web Contact
If your product is not working properly and your troubleshooting is
unsuccessful, please contact WESPER technical support at www.wesper.co
/contact-us. Additional answers to your
product and technical questions can be found at
support@wesper.co. Contact Wesper Inc. Customer Relations
at support@wesper.co.
Changes To These Terms
We reserve the right to update, change or replace any of the terms contained
in this document or in other WESPER documentation by posting updates and/or
changes to our website, www.wesper.co. It is your
responsibility to check our website from time to time for any updates or
changes, as they are binding on you. © 2021 Wesper Inc. Any unauthorized
copying, duplicating, or other reproduction of the contents hereof is
prohibited without written consent from Wesper Inc. All rights reserved.
Wesper Inc., 234 5th Ave, New York, NY 10001, USA. PCK000001-REV02
Get Started
- Connect the charger to an outlet with the cable provided
- Make sure the charger and back of the patches are clean and free of any debris.
- Place the patches onto the charger. Confirm the blue corner charging LEDs are illuminated. If they aren’t, gently move the patches around until they are to ensure charging.
- Charge the patches for at least 3 hours. Depending on your patch model, the corner charging LED may turn off when charging is complete or remain on.
- Install the Wesper app from the App Store and create an account. We’ll take it from there!
Preparing For Your Test
Apply a new set of adhesive backings:
- Make sure the back of the patch is clean and dry.
- Remove one of the adhesive liners using the pull tab.
- Align the adhesive over the shape of the patch and press firmly.
- Repeat application on the second patch.
- Open the app and start a new test, following the in-app instructions. Sweet dreams!
Having trouble?
Find frequently asked questions, troubleshooting tips, and more at
wesper.co/faq
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>