TECNO N1 Wireless Headset Nightingale User Manual

TECNO N1 Wireless Headset Nightingale

WELCOME

Thank;w for crossing our produce. The Nightingale-N1 wireless earphone has a fashionable design, powerful functions, and high compatibility, providing you with hands-free convenience in making calls and listening to music.

PACKAGE CONTENT

• 1 x Nightingale-N1 Wireless Earphone
• 1 x USB Charging Cable
• 1 x Audio Transmission Une
• 1 x User Manual

WIRELESS TECHNOLOGY
With the wireless technology, you can connect earphones to its compatible commune:alion devices without using cables. The wireless c allows you to use a cell phone without holding tt against the earphone, but the maximum distance between them cannot exceed 10 meters (The distance between open areas can be increased). The wireless connection may be interfered by obstacles (such as walls) or other electronic devices. In some areas, use of the wireless technology may be subject to some constraints. Please consult your local authority or service provider for details.On behalf: Manufacturer: TECNO MOBILE LIMITED Add: ROOM 6046/F SOUTH TOWER WORLD FINANCE CTR HARBOUR CITY 17 CANTON ROAD TST KL (place and dale of issue): Shenzhen, 2020-02-21 (name, function): Ying Luo’ Manager

HOW TO USE

Charging

1.  Connect the charging port with any USB charging adapter or active computer USB port.
2.  Charging will start automatically with LED indicating red.
3.  The earphones are fully charged when LED indicates blue. Nole: Make sure the gallery is fully charged before putting the earphones away for storage. Charge the earphones at least once CNery 3 months when not using for a long time.

Pairing

1. Make sure the earphones and your BT device are next to each other (within 1 O meters).
2.  (no pairing information) when off, press the power switch for 2-3 seconds to start the headphone, and it will enter the pairing state.
3.  (has pairing information)when off, press the power switch for 2-3 seconds to start the headphone. fail to connect to the last coonected device within 1 O seconds, the headphone enters the pairing stale.
4. When the headset is CX11necled to the device, the device disconnects from the headset or turns off the bluetooth in the Settings interface, the headset enters the pairing stale. Bluetooth connected: blue light flashes slowly once every 5 seconds Prompt tone: Connected Unconnected Bluetooth: blue light flashes when connected back. red and blue light flashes alternately when paired Prompt tone: Disconnected

Note:

1.  The wireless earphones can remember previous pa.ired devices.
2. If the earphone cannot pair with your BT device. Press the volume + button and volume- button at1he same time for 5 sec:onds under the startup stale. The red and blue light flashes twice at the same time to clear the pairing history. Then restart the earphone to pair again.

OPERATION AND FUNCTIONS

Power On| When off, press the power switch for 2-3 seconds until the blue light ls on.
---|---
Power Off

Pairing

| When on, press the power switch for 5 seconds until the red light is on

when off, press the power switch for 2-3 seconds to start the headphone

Volume +/-

Next Track/ Previous Track

| Click the volume+/ volume-

Short press the previous ‘,,ey/ Last ‘,,ey

Play/Pause| short press the power switch to pause
Answer/ Hang up a Call| Short press the power switch
Reject the| Long press the power switch for 1
Incoming Call| second and then release
Re-dial Last Call| double-click the power switch

Restore to Factory Setiings

| P res s the volum <>+ button and volume- button at the same time for 5 seoonds under the startup state

Voice Dialing

| long press the power switch for 1 second Siri can be reached � you release the power switch within 1-1.5 seconds

EU DECLARATION OF CONFORMITY
in accordance with
Annex VI of Directive 2014153/EU of the European Parliament and of the Council

1.  For the following Radio equipment:
   Model: N1
   Product: Wireless headset
   Trade name or Brand: TECNO Software I Hardware number. 551-BES2300I1-W01

2. Name and address of the manufacturer or his authorized representative: Manufacturer. TECNC MOBILE LIMITED
   Add: ROOM 604 6/F SOUTH TOWER WORLD FINANCE CTR HARBOUR CITY 17 CANTON ROAD TST KL.

3.  This declaration of conformity is issued under the sole responsibility of the Manufacturer.

4.  The object of the declaration (identify:alion of the radio equipment allowing traceability; It may include a color image of sufficient clarity where necessary for the identification of the radio equipment):

5.  The object of the declaration described above ls in conformity with the relevant Union harmonization legislation: Directive 2014 /53’EU (RED)

6.  References to the relevant harmonized standards used or references to the other technical specifications in relation to which conformity is declared:

7.  Notified Body Name: MET Laboratories, Inc. Notified Body Number. 0980 Notified Body Assessment Performed: Module B/C on Article 3. 1 a, 3.1 b, 3.2 and 3.3 Technical File identification Number. NIA

8.  Where applicable, description of accessories and components, including software, which allow the radio equipment to operate as intended and covered by the EU declaration of conformity: User instructions are provided in the User Manual. The Software and Hardware versions are specified above.

9. Additional information: Referring to Article 10.2 of the DirectM>, this equipment is so constructed that It can be operated in all Member Stales, without infringing applicable requirements on the use of radio spectrum. Referring to Article 10.1 o of the DirectM>, there are no restrictions on putting this equipment into service or of requirements for authorization of use. Please refer to the User Manual for details.Hereby, TECNO MOBILE LIMITED.
   Declares that this Wireless headset is in compliance with the essential requirements and other relevant provisions of directive 2014153/EU.

CAUTION

1. Risk of explosion if the battery is replaced by an incorrect type, dispose of used batteries according to the instructions.
2.  The product shall only be connected to a USB interface of version USB2.0
3. The adapter shall be installed near the equipment and shall be easily accessible.
4. EUT Temperature:o·c ~-145″C.

SPECIFICATION

PRODUCT OVERVIEW

1.  LED ink:ator light
2.  Power button
3. Micro USB
4. Aux-in port
5. Mic
6. Volumi>+
7.  Volume-
8.  Previous track 9.Next track

Customer service

Name:

Address:

|
---|---
Tel.No:|
Dale of �rchase: (dcllmm’yy)|
Store name:|
SIN:|

WARRANTY TERMS & CONDmONS 365 DAYS WARRANTY

Please keep well your receipt, this warranty covers only original TECNO products. It is not applicable to normal wear and tear, or any effects or damage caused by misuse of the product. Warranty is for primary products only. Additional or free-of-cost products are not covered under warranty.

TECNO MOBILE LIMITED
TM and ©2019 TECNO Corporation. All rights reserved. Other product and company names mentioned herein may be trademarks or trade names of their respective owners. Specifications are subject to change without notice. Model names and the availability of particular products may vary by region.

FCC Caution:

Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1.  This device may not cause harmful interference, and
2.  this device must accept any interference received, including interference that may cause undesired operation.

IMPORTANT NOTE:
Note:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause hamiful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause hannful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
•  Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• consult the dealer or an experienced radio/TV technician for help.

FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>