SIIG CE-KV0H11-S1 4-Port DisplayPort 1.4 8K MST Dual Head KVM Console Switch User Manual
- October 27, 2023
- SIIG
Table of Contents
S1 4-Port DisplayPort 1.4 8K MST Dual Head KVM Console Switch
User Manual
Safety and Notice
The device has been tested for conformance to safety regulations and requirements, and has been certified for international use. However, like all electronic equipment, the device should be used with care. Please read and follow the safety instructions to protect yourself from possible injury and to minimize the risk of damage to the unit.
- Follow all instructions and warnings marked on this unit.
- Do not attempt to service this unit yourself, except where explained in this manual.
- Provide proper ventilation and air circulation and do not use near water.
- Keep objects that might damage the device and assure that the placement of this unit is on a stable surface.
- Use only the power adapter and power cords and connection cables designed for this unit.
- Do not use liquid or aerosol cleaners to clean this unit.
- Always unplug the power to the device before cleaning.
 Thank you for Your Purchase!
Features
- DisplayPort 1.4 compliant
- Supports up to 8K@30 Because bandwidth limit. Please refer to the MST Video output table to adjust the video output resolution.
- Supports DSC 1.2
- HDCP 2.2 compliant
- Video bandwidth: 32.4Gbps
- Supports SST or MST (Multi-Stream Transport)
- Supports separate line input and output
- Plug and Play without any driver needed
- Supports built-in 4-port USB 3.2 Gen 1 HUB to share USB devices
- Supports independent HID keyboard & mouse ports
- Supports hotkeys function
- EDID Bypass
- Firmware upgradable for support of new features and technology enhancements
- The KVM can switch every input by push buttons
Package contents
- 4-Port DisplayPort 1.4 8K MST Dual Head KVM Console Switch
- Power adapter DC 12V/2A
- USB 3.0 + MIC + Stereo cable x4
- DP Cable x4
- User Manual
What is DisplayPort MST? (Multi-Stream Transport)
MST has been a feature of the DisplayPort standard since version 1.2 was
released. The key factor of the technology’s usefulness for desktop users is
that it allows multiple independent displays to be driven from a single
DisplayPort output source device.
The combined data requirements of all the displays cannot exceed the limits of
the single DisplayPort port that the video source origi-nates from, nor exceed
the capabilities of your graphics cards.
MST Video output table
| DP 1.2
Host| DP 1.4
Host
---|---|---
Signal
Display| 4K60| 8K30
Dual
Display| 4K30
+ 4K30| 4K60
+ 4K60
Note
- DisplayPort 1.2 spec does NOT support HDR
- The suggested DisplayPort cable length is 13m to 2m
- DisplayPort does NOT support dongle device .
- MacOS does NOT support MST technology and will only mirror each display
- AMD graphics card does NOT support MST mode
Layout
- Port 1-4 Selection Push Button: Switch between computers
- USB 3.0 Hub: Connect to USB devices 5V/0.9A
- Console USB HID Ports: For keyboard & mouse only
- KVM Video IN 1-4: Connect the OP cable to PC
- Console MST Video OUT: Connect the DP cable to a display Please refer to “MST Video output table”
- +12V DC: +12V DC power jack
- Power Status: Power indicator LED
- Micro USB: For F/W update
- USB 3.0 Hub: Connect to USB devices 5V/0.9A
- Speaker OUT: Connect to analog stereo audio speaker
- Mic IN: Connect to analog stereo audio source
- KVM USB 3.0(Type B): Connect the USB cable to PC
- KVM speaker 1-4: Connect the stereo cable to PC
- KVM Mic 1-4: Connect the stereo cable to PC
- 2-Pin Dip Switch: For F/W update
Dip Switch
| Position | Description |
|---|---|
| PIN#1 | ON[ ] |
| OFF[ ] | Working mode |
| PIN#2 | ON[ ] |
| OFF[ ] | Reserved |
Application
Hotky
Default setting, all of the following commands begin by pressing the [Scroll Lock] or [Ctrl] key twice. Please follow the hotkey command listed below for selected operating functions:
Hot key Definition
(Scroll Lock) + (Scroll Lock) + [0] + (F] + (9| Turn off HOTKEY function
[Scroll Lock] + [Scroll Lock] + [0]+ [N]| Turn on HOTKEY function
(Scroll Lock) + (Scroll Lock) + (NUMBER1-4) + [Enter]| Switch input 1-4 source
to output
[Scroll Lock] + [Scroll Lock] + [5]| Auto Scan/ Exit Auto Scan mode (Note 2)
(Note 3)
(Scroll Lock] + [Scroll Lock) + (+]| Auto Scan Interval Add S Seconds
(Scroll Lock] + [Scroll Lock) + [-]| Auto Scan Interval Subtract 5 Seconds
[Scroll Lock] + [Scroll Lock) + [L] + [A]| Audio Lock / Audio Unlock
(Scroll Lock] + [Scroll Lock) + [L] + [U]| USB Lock / USB Unlock
Note:
- Auto scan through each channel for quick screen browsing (default = 15 seconds)
- You can set the auto scan interval according to the steps. (N = Number, 5-599)
Firmware update
- Connect the Micro-USB to USB cable between PC and device
- Set dip switch PIN#1 to ONES] and then power on device
- Open firmware update software and then select COM Port
- Click “KVM” button to open “KVM Firmware Update” windows
- Check all items and click each “…” button to select the file which you want to write into device.
- Click the “Burn!” button to start firmware update
- After updating, please set the dip switch PIN#1 to OFF [*1 and power cycle the device
Support
For more info or tech support:
http://www.slig.com/support
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>