SIIG 04-1353A 3×1 HDMI 2.0 Switch with IR and Voice User Manual
- June 4, 2024
- SIIG
Table of Contents
SIIG 04-1353A 3×1 HDMI 2.0 Switch with IR and Voice
Safety and Notice
The device has been tested for conformance to safety regulations and requirements, and has been certified for international use. However, like all electronic equipment, the device should be used with care. Please read and follow the safety instructions to protect yourself from possible injury and to minimize the risk of damage to the unit.
- Follow all instructions and warnings marked on this unit.
- Do not attempt to service this unit yourself, except where explained in this manual.
- Provide proper ventilation and air circulation and do not use near water.
- Keep objects that might damage the device and assure that the placement of this unit is on a stable surface.
- Use only the power adapter and power cords and connection cables designed for this unit.
- Do not use liquid or aerosol cleaners to clean this unit.
- Always unplug the power to the device before cleaning.
Features
- Support panel, remote control, APP, Alexa switching
- Support 2.4G wireless for APP & Alexa control
- Support app control switching via the Magic Home app
- Support voice control switching via Alexa to control the switcher
- Support high definition resolution 4K@60Hz and full 3D
- Support 600MHz per channel bandwidth (18Gbps all channels)
- Support 12bit per channel (36bit all channels) deep color
- Support HDCP 2.2
- Support High Dynamic Range (HDR) and Dolby Vision
- Support LPCM, DTS, Dolby Digital 5.1 & 7.1 audio
- Support CEC Consumer Electronics Control
- Support Smart Switching when new source in, source removed and memory function.
Package contents
- 3×1 HDMI 2.0 Switch
- Power adapter DC 5V/1A
- IR Remote control
- User Manual
Layout
- Pressing to select the previous source
- Pressing to select the next source
- 1 /2/3: Pressing the number to select the input source accordingly
- MEMORY: Pressing “MEMORY” to get the switch remember the active input source, and select this input source port automatically when restarts.
Rear Panel
- lnput1-3: HDMI Input 1-3 Port
- TV/Display: HDMI Output Port
Side
- Power: DC 5V/1A
Front Panel
- Power LED Indicator
- SWITCH: Short press to change the input channel and long press to reset the Wi-Fi module
- IR Signal Receiver Port
- Statues: Wi-Fi Module Status LED Indicators
- No matching: Flicker Quickly
- Get matching: Flicker Slowly
- Get matched: No LED Light
- Output Port LED Indicators
- 1 /2/3: Input Port 1 /2/3 LED Indicators
- Red LED indicates “Signal Not Selected”.
- Blue LED indicates “Active Signal Path”.
- No LED indicates “No Input Signal”.
App Control
- Download the “Magic Home” App from the Google Play or Apple Store firstly and install it
- Open the Magic Home app, sign up an account with your mobile phone or email, and then to sign in to the app, the login area is selecting United States.
- After entering app, click home icon in the lower left corner of UI, and select “Add device” then select universal remote device.
- Long press the smart switcher select button for 1 Os to reset the Wi-Fi module till the states LED light starts to flicker quickly.
- When the states LED flicker quickly, click the operation confirmed option and then click NEXT.
- Select the Wi-Fi you want to connect to (only 2.4 GHz band Wi-Fi is supported), don’t recommend the guest mode Wi-Fi to avoid the matching issue with the smart switcher and the phone or other devices via the app, and then enter your password and click Next.
- When matching, a matching progress Oto 100% will be displayed on the mobile phone’s app. When matching is connected, the LED status light will flicker quickly to slow flicker and finally not flicker. When matching is completed, you can click smart switcher icon from the HOME page and enter the smart switcher control UI. You can control the smart switcher via the app UI at any places which can connect to Ethernet normally.
Note: Please keep the smart switcher and phone which used to match and control
the smart switcher as closer as possible to the router to keep the wireless
signal.
Amazon Alexa Setting
- Active the Skills to link the “Magic Home” app
- At the Amazon Alexa page, you need to select “Skills” option and input “Magic Home Lite” and click “search” button to enter the next step.
- Confirm the two steps are finished and click the next icon.
- Choose the American region as default, regardless of which country the customer actually uses
- As registered the account with Email address or phone number and Password at the front and fill in it at this page.
- At this step, the magic home lite has been successfully linked. You can use voice control the switcher to change input source via Alexa.
Alexa voice command list
Troubleshooting
Problems Causes Solutions
Power liaht is off an
product is not working
| Is the power adapt- er progerly con- necte| Please check if the power
adapter is connected properly
---|---|---
Screen splash| HDMI cable may not be HDMI 2.0 speci- fication or the cable is
too long| Please use the standard HDMI 2.0 cable, the input/ output cable
length does not exceed SM 4K/60Hz 4:4:4,
4K@30Hz/1080fc can reach 1OM o 10M
Can’t match the smart switcher and the phone or other devices via app| Maybe the smart switcher and the phone is not closer as recommended with the router when matching| Please keep the smart switcher andcFhone which use to match and control the smart switcher as closer as possible to the router. And we don’t recommend mode Wi-11to
to use the uest
1
matching
Can not
control the smart switch via app via . phone or voice via Alexa
| Maybe the match-
ing between the smart switcher and the phone has not finish {et, and the skill o the Alexa doesn’t enable the app to activate yet.
| Please matching the
smart switcher and the phone
follow the stegs as “To match he
Smart Switcher with the phone with app” and enable the app skill of the Alexa follow the ste s as “To activate S ills”
Thank You for your purchase!
Support
For more info or tech support http://www.siig.com/support