TRIPP LITE N784-H01-SCMM Hardened 10p-100 Copper to Fiber Media Converter User Guide

TRIPP LITE N784-H01-SCMM Hardened 10p-100 Copper to Fiber Media Converter

Product Features

•  Extends a 10/100 Mbps Ethernet connection over SC multimode fiber cable up to 2 kilometers (N784-H01-SCMM)
•  Extends a 10/100 Mbps Ethernet connection over ST multimode fiber cable up to 2 kilometers (N784-H01-STMM)
•  Extends a 10/100 Mbps Ethernet connection over SC single-mode fiber cable up to 30 kilometers (N785-H01-SCSM)
•  Hardened housing withstands high operating temperatures
•  Provides ESD, RFI, and surge protection
•  LEDs indicate Ethernet connection and fiber link status
•  DIP switches control Local Loop Back testing (LLB), Remote Loop Back testing (RLB), Link Fault Signaling (LFS) and Reserve functions
•  Link Fault Signaling (LFS) LED indicates when a cable has been severed or another cause for disruption has occurred
•  Local LoopBack (LLB) tests the copper network connection
•  Remote Loop Back (RLB) tests the fiber network connection
•  Auto MDI/MDI-X functionality removes the need for crossover cabling

Package Contents

•  N784-H01-SCMM or N784-H01-STMM or N785-H01-SCSM Media Converter
•  External Power Supply with NEMA 1-15P Plug (Input: 100-240VAC, 50/60 Hz, 0.5A; Output: 12VDC, 1.5A)
•  DIN Rail Kit
•  Mounting Hardware
•  L-Shaped Bracket
•  Rubber Foot
•  SC Connector Cap (N784-H01-SCMM and N784-H01-SCSM)
•  ST Connector Cap (N784-H01-STMM)
•  Quick Start Guide

Optional Accessories

•  N001-Series Cat5e Snagless Patch Cables
•  N201-Series Cat6 Snagless Patch Cables
•  N302-Series Duplex Multimode 62.5/125 Fiber Patch Cables (ST/ST)
•  N306-Series Duplex Multimode 62.5/125 Fiber Patch Cables (SC/SC)
•  N356-Series Duplex Singlemode 9/125 Fiber Patch Cables (SC/SC)•
• N785-CH12 12-Port Chassis for N784/N785 Media Converters

Installation

Notes:

•  The following installation instructions refer to an installation in which two media converters are used. A single media converter can be used for a copper-to-fiber installation.
•  The following installation instructions refer to the N784-H01-SCMM. Connections are the same for all models, with only the specs being different. See the Specifications section in this manual for details on your media converter.
•  To avoid damage due to Electrostatic Discharge (ESD), it is recommended you handle the product while wearing an ESD wrist grounding strap or by touching a conductive surface (such as metal) to discharge any potential ESD prior to handling the product.

1.  Connect the media converter to a second identical media converter using the appropriate type of fiber cable, making sure to connect the TX port on one unit to the RX port on the other.
   Note : See the Product Features section in this manual to determine which type of fiber cable is supported by your media converter.

2.  Connect the RJ45 port on the second media converter to your network device (workstation, hub, switch, etc.) using a Cat5e/6 cable.

3.  Connect the external power supplies that came with each media converter, and plug them into an AC power source.

LED Status Table

Link Fault Signaling (LFS)
The LFS LED will indicate when a cable has been severed or when some other cause of disruption in service has occurred. The LFS function monitors both copper and fiber segments for a total service report. Set DIP Switch 1 (LFS) to ON for normal operational use and to OFF when installing cables or when testing the network connection.

LoopBack Test
Each media converter features DIP switches to activate both local and remote loopback diagnostic test functions. Use the Local Loop Back (LLB) function to check if the copper segment is connected properly. Use the Remote Loop Back (RLB) function to check if the fiber segment is connected properly.
Note: When enabling loopback testing in one segment of the connection the other segment will be blocked until the loopback is disabled.

Specifications

__

IEEE

Standards Supported

| 802.3 10Base-T 802.3u

100Base-TX/FX

802.3

Auto-Negotiation

| 802.3 10Base-T 802.3u

100Base-TX/FX

802.3

Auto-Negotiation

| 802.3 10Base-T 802.3u

100Base-TX/FX

802.3

Auto-Negotiation

Power Consumption| 1.8W
Power Supply Input| 100-240VAC, 50/60 Hz, 0.5A
Power Supply Output| 12VDC, 1.5A
Operating Temperature| 14° to 140°F / -10° to 60°C
Storage Temperature| -40° to 185°F / -40° to 85°C
Relative Humidity| 5% to 95% RH, Non-Condensing
Unit Dimensions (H x W x D)| __

0.92 x 2.9 x 4.3 in. / 23.4 x 73.8 x 109.2 mm

Warranty and Product Registration

2-Year Limited Warranty
Seller warrants this product, if used in accordance with all applicable instructions, to be free from original defects in material and workmanship for a period of two (2) years from the date of initial purchase. If the product should prove defective in material or workmanship within that period, Seller will repair or replace the product, at its sole discretion.
THIS WARRANTY DOES NOT APPLY TO NORMAL WEAR OR TO DAMAGE RESULTING FROM ACCIDENT, MISUSE, ABUSE OR NEGLECT. SELLER MAKES NO EXPRESS WARRANTIES OTHER THAN THE WARRANTY EXPRESSLY SET FORTH HEREIN. EXCEPT TO THE EXTENT PROHIBITED BY APPLICABLE LAW, ALL IMPLIED WARRANTIES, INCLUDING ALL WARRANTIES OF MERCHANTABILITY OR FITNESS, ARE LIMITED IN DURATION TO THE WARRANTY PERIOD SET FORTH ABOVE; AND THIS WARRANTY EXPRESSLY EXCLUDES ALL INCIDENTAL AND CONSEQUENTIAL DAMAGES. (Some states do not allow limitations on how long an implied warranty lasts, and some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitations or exclusions may not apply to you. This warranty gives you specific legal rights, and you may have other rights which vary from jurisdiction to jurisdiction.)

WARNING: The individual user should take care to determine prior to use whether this device is suitable, adequate or safe for the use intended. Since individual applications are subject to great variation, the manufacturer makes no representation or warranty as to the suitability or fitness of these devices for any specific application.

Product Registration
Visit tripplite.com/warranty today to register your new Tripp Lite product. You’ll be automatically entered into a drawing for a chance to win a FREE Tripp Lite product:” No purchase necessary. Void where prohibited. Some restrictions apply. See the website for details. WEEE Compliance Information for Tripp Lite Customers and Recyclers (European Union) Under the Waste Electrical and Electronic Equipment (WEEE) Directive and implementing regulations, when customers buy new electrical and electronic equipment from Tripp Lite, they are entitled to:

•  Send old equipment for recycling on a one-for-one, like-for-like basis (this varies depending on the country)
•  Send the new equipment back for recycling when this ultimately becomes waste

Use of this equipment in life support applications where the failure of this equipment can reasonably be expected to cause the failure of the life support equipment or to significantly affect its safety or effectiveness is not recommended. Tripp Lite has a policy of continuous improvement. Specifications are subject to change without notice. Photos and illustrations may differ slightly from actual products.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>