CTEK CONNECTED 2 Daisy Chain Ethernet Switch Kit Instruction Manual
- June 6, 2024
- CTEK
Table of Contents
CTEK CONNECTED 2 Daisy Chain Ethernet Switch Kit
**
**
Purpose
This manual explains how to install the daisy chain kit (art no 40-467), to enable support for daisy-chaining of power and ethernet connection for the Chargestorm Connected series This kit is compliant with pole mount kits 922-00018 and 922-00019
Safety
- Only an accredited electrician is allowed to perform the installation described in this document
- Read and obey the instructions in this document before installation and operation of the product
- Installation must fulfill local safety regulations
- Use safety shoes during the installation
National usage restrictions
Some countries, states or provinces have other electrical codes and standards
than stated in this manual The installation and usage of the product shall
follow local regulations The product is intended for use by the general public
- The product is intended for locations with both restricted access and non-restricted access
- This product is only allowed for use in the following regions: CZ, DE, DK, GR, ES, FI, FR, IT, NL, NO, PL, SE, UK, AT, BE, CY, IE, LU, and MT
To prepare the installation
- Prepare and mount internal power wires and the ethernet cable of the Chargestorm Connected series before attaching to the daisy chain kit
- Make sure that the holes are drilled correctly Refer to the manual for Chargestorm Connected 2
Tools
Materials included
- Fuse
- Power supply.
- Ethernet switch
- Terminal blocks, L1-L3, N, PE
- Power supply cable switch
- DIN-mounted terminal block
- Ground cable from terminal blocks to the power supply unit (6mm2)
- Phase cable from the fuse to the power supply unit (25mm2)
- Neutral cable from the fuse to the power supply (25mm2)
Materials not included
- Ethernet cable
- Main input cable to the terminal blocks
Overview of the installation
- Ethernet switch
- Power supply
- Ground terminal block
- Fuse
- Terminal blocks, L1-L3, N, PE
To install the switch kit
To do a test of the power supply
To install the Ethernet cable
To install the power cables in Chargestorm Connected
To recycle the product
The product must be recycled as electronic equipment Follow the local
requirements for recycling of electronic equipment
References
- CHARGESTORM® CONNECTED 2 Installation manual (Pd_IM_0011)
- 6 ports Fast Unmanaged Industrial PoE Switch Manual
Revisions
The descriptions, information, and specifications contained in this manual
were in effect at printing To make sure that the maintenance instructions are
complete and up to date, always read the manual published on our website
Copyright
These instructions are delivered “as is” and contain content that can change
without prior notice CTEK E-Mobility AB does not guarantee that everything is
correct in the instructions CTEK E-Mobility AB is not responsible for faults
or incidents or damage that is caused by not following the instructions in
this manual © Copyright CTEK E-Mobility AB 2020 All rights restricted Copying,
adaption, or translation of these instructions are strictly forbidden without
written approval by CTEK E-Mobility AB, except what is regulated by copyright
laws CTEK E-Mobility warranty statement
Limited warranty
CTEK issues a limited warranty to the original purchaser of the product
Depending on the product, the limited warranty period will vary The limited
warranty is not transfer-able The warranty applies to manufacturing faults and
material defects The warranty is void if the product has been handled
carelessly or repaired by anyone other than CTEK or its authorized
representatives CTEK makes no warranty other than this limited warranty and is
not liable for any other costs other than those mentioned above, no
consequential damages Moreover, CTEK is not obligated to any other warranty
other than this warranty
Circumstances that will void the limited warranty
If the seal of the product is broken, purposely damaged, or in any way
modified or al-tered; including cables, electronics, mechanics or other parts
of the product; products that have been repaired by anyone other than CTEK or
its authorized representatives; products that have been subject to the use of
supplies and accessories other than those approved in writing or supplied by
CTEK; improper use or non-compliance with installation, commissioning,
operation or maintenance instructions (ie not according to the operation and
installation manual); unauthorized modifications, changes or at-tempted
repairs; vandalism, destruction through external influence and/or
persons/animals; failure to observe applicable safety standards and
regulations; faults caused by fire, water, snow, moisture, or other liquids
except as specified for normal use; prod-ucts where the serial number is
defaced, altered or removed; any utilization of a product that is inconsistent
with either the design of the product or the way CTEK intended the product to
be used; any installation and/or modifications that prevent normal service of
the product; normal wear and tear and cosmetic damage such as, but not limited
to, corrosion, scratches, dents, rust, stains, non-functional parts such as,
but not limited to, plastics and finishes; damage, fault, failure and/or
imperfection caused by abuse, tampering, illegal use, negligence, prolonged
use or operation; or faults in any other way caused by the
customer/retailer/user
Additional information
CTEK makes no other warranty than as set out herein and CTEK shall in no event be lia-ble for any indirect or consequential damages The faulty product shall be returned with the receipt to the retailer/place of purchase together with a fault description Goods returned to CTEK will be at CTEK’s discretion and only valid with an approved Return Ma-terial Authorisation (RMA) Reference Number issued by CTEK to the purchaser Prod-ucts sent directly to CTEK without an RMA will be returned to the sender at the sender’s cost The warranty period for a product is stated in the applicable product user manual supplied with the product The warranty is only valid if the warranty period has not ex-pired If the warranty claim of a faulty product is not approved by CTEK, the product will be returned only if the sender explicitly so requests The customer/retailer/place of purchase will pay the freight Faulty products will be repaired, or replaced with an exchangeable product, and returned at CTEK’s cost If the warranty period has expired, the product will be returned without further investigation at the cost of the customer/retailer/place of purchase Faulty products will be scrapped by CTEK if deemed not re-pairable CTEK reserves the right to vary, modify or change the terms and conditions herein due to change(s) in availability of services, products and/or spare parts, or for the purpose of complying with applicable policies, rules, regulations and law, without notice
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>