PATPET P-COLLAR910 Dog Training Collar User Manual
- June 6, 2024
- PATPET
Table of Contents
- Package Contents
- Overview
- Important Safety Information
- Charge The Remote And Receiver Collar
- Turn On The Remote And Receiver Collar
- Fit the Receiver Collar
- Beep
- Vibration
- Static Stimulation
- How To Find The Best Static Level For Your Dog?
- Main Features
- How to Use Test Light Tool
- Training Tips
- Pairing
- Question & Answer
- Troubleshooting
- Warranty
- Compliance FCC-USA
- Documents / Resources
Dog Training Collar User Manual
0.30.02.910×00-PT-10
Package Contents
Overview
Hand Remote Control
Important Safety Information
This is the safety alert symbol. It is used to alert you to potential injury hazards. Obey all safety messages that follow this symbol to avoid possible injury.
Not for use with aggressive dogs. Do not use this product if your dog is prone to aggressive behavior. Aggressive dogs can cause severe injury to their owners and others. If you are not sure if this product is right for your dog, please check with your veterinarian or a certified trainer.
Safety during on-leash training.
While learning during on-leash training. Your dog should be on a strong leash,
long enough for him to attempt to chase an object, but short enough for him
not to reach a road or other unsafe area. You must also be physically strong
enough to restrain your dog when he tries to chase.
Risk of skin damage.
A collar worn for too long or made too tight on the pet’s neck may cause skin
damage ranging from redness to pressure ulcers. This condition is commonly
known as bed sores.
- Avoid leaving the collar on the dog for more than 8 hours per day.
- When possible reposition the collar on the pet’s neck every 1-2 hours.
- Never connect a lead to the electronic collar, it will cause excessive pressure on the contacts.
- If a rash or sore is found, discontinue use of the collar until the skin has healed.
- If the condition persists beyond 48 hours, see your veterinarian.
- This product is not a toy, please keep it away from children.
- This product is only for use with healthy dogs over 6-month-old.
Charge The Remote And Receiver Collar
USB C Charging Port When charging is completed steady green light.
Turn On The Remote And Receiver Collar
Press and hold the
ON/OFF Button for 2 secs to turn on the remote.
Press and hold the ON/OFF Button for 2 secs to turn off the remote.
Press and hold the power button for 2 secs to turn on the receiver
collar, the receiver collar vibrates 1 time and the green LED flashes 1 time.
Press and hold the power button for 2 secs to turn off the receiver collar,
the receiver collar vibrate twice and the red LED flashes twice.
Note: To extend the battery life, please turn the receiver collar off
when it is not in use.
Fit the Receiver Collar
Note: The Contact Points must have direct contact with the dog’s neck skin. Check the tightness of the Collar by inserting one finger snugly between the collar and neck.
Beep
Delivers a Beep tone with non-adjustable volume to the receiver collar
Vibration
Delivers a vibration with a non-adjustable level to the receiver collar.
Static Stimulation
Delivers currently selected level static stimulation to the receiver collar. Note: Please use with caution static stimulation, some dogs may not respond to lower levels. See the “Flow To Find The Best Static Level For Your Dog” (Page 8). “1” means the lowest level, “16” means the highest level.
How To Find The Best Static Level For Your Dog?
Very Important: Always start at the lowest level and choose the level that is best for your dog. Follow the steps below to find the best Level: Step 1: Starting at Level 1, press the static button to see the dog’s reaction. Step 2: Gradually increase the stimulation levels until your pet reliably responds to the stimulation. Step 3: If your dog continues showing no response at Level 6, check the fit of the receiver collar. If your dog has long or thick hair, install a contact spring sheet, or the dog’s hair will need to be trimmed around the contact points, If “the Contact Points” is no contact with the dog’s skin, there will be no static stimulation. Note: If all of these steps have been done and the dog continues showing no reaction, see the “How to Use Test Light Tool”(Page 10).
Main Features
| Vibration, Beep, and Static training mode
---|---
1-16 adjustable static level
Battery status display for the Remote
The receiver collar is IPX7 waterproof (the Remote is not waterproof)
The remote range is 3/4 mile
Long-life Lithium Polymer battery
Support maximum 2 receiver collars with 1 remote
USB C charging port
How to Use Test Light Tool
A : Static function test
- Make sure the Remote and Receiver Collar are paired.
- Put the test light tool vertically on the 2 contact points, making sure the metal wire has direct contact with the top of the 2 points.
- Press the static button on the Remote. The test light will be lighted. The higher the static level is the redder the light will be.
Note: For dogs with shorter coats use 2pcs short contact points and install the conductive silicone caps onto the contact points to make it softer. It may be better for your dog’s skin. For dogs with thicker coats, Please use 2pcs long contact points and install a contact spring sheet.
Training Tips
If you want to correct the dog’s bad behavior, for example, barking, please follow these training steps.
- Put a separate non-metallic collar on your dog’s neck above the receiver collar, and attach an 8-10 feet leash. Caution: Be sure the extra collar does not put pressure on the contact points.
- Hold the leash and the remote.
- Choose your pet’s recognition static level.
- As soon as your pet is barking, press the Stimulation button and give the command “No” or “No barking”.
- Release the stimulation button immediately once your dog stops barking and praises it.
- If your pet ignores the stimulation, increase the intensity level by 1 to 3.
- Practice this training in several different scenes.
Pairing
Notes: You may skip this step because the set is already paired with the factory setting.
-
Make sure the Receiver is turned off and the channel switch is on “Dog 1”.
-
Press and hold the power button of the receiver collar for 3 secs until the red and green lights flash alternately.
-
Press and hold the remote Beep+Vibration buttons at the same time to pair the receiver collar.
-
Pairing successful: the receiver collar beeps 3 times and the green light flashes 3 times.
Two Receiver Collars System Part
I: Pairing 2nd Receiver Collar.
Note: You need to own an additional receiver collar.
Receiver:
- Make sure the receiver collar is turned off and the channel switch is on “Dog 2”.
- Press and hold the power button of the receiver collar for 3 secs until the red and green lights flash alternately.
- Press and hold the remote Beep+Vibration buttons at the same time to pair the receiver collar
- Pairing successful: the receiver collar beeps 3 times and the green light flashes 3 times.
Part II : Receiver Switching.
Able to train 2 dogs separately. The regulator channel switch selects the dog
to train.
Question & Answer
Q: Is the static-safe for my pet?
A: Static electricity may hurt your pet, please select the appropriate static
electricity level. Electronic training equipment requires the interaction and
training of the owner.
Q: How old does my pet have to be before using the Electronic Training
Collar?
A: Your pet should be able to recognize basic obedience commands such as “sir
or -Stay. Pets should be at least 6 months old before using the Training
Collar.
Q: Once my pet is trained and has been obeying my commands, will he have to
continue to wear the receiver collar?
A: It is recommended to wear it until you completely correct the dog’s bad
behavior.
Q: Is the Receiver Collar waterproof? A: Yes, the receiver collar is IPX7
waterproof. But the remote is not waterproof. Please keep the remote away from
the water.
Q: Will I get exactly 3/4 mile of range with the electronic training
collar?
A: The effective wireless communication range will be affected by terrain,
weather, vegetation, and interference from other radio equipment.
Q: How can I get support when I have product problems?
A: Please feel free to contact our official customer service mailbox, any
problems with the product will be resolved here s
service@patpet.com.
Troubleshooting
My pet does not respond when i press a button.
- Make sure the receiver collar has been turned on.
- Make sure the remote channel 1 or 2 is correct with the receiver collar. If not, please pair the remote and the receiver collar again. Refer to “Paring” (Page 13) for more information.
- Check that the battery may be low in either the remote or the receiver collar.
- Make sure the receiver collars’ contact points are placed snugly against your pet’s skin. Refer to “Fit The Receiver Collar” (Page 6) for more information.
- Terrain, weather, vegetation, transmission from other radio devices, and many other factors can impact the amount of range you have with the unit.
Warranty
1-Year Warranty
The original purchaser for this unit is provided with a 1-YEAR Warranty. The
warranty begins on the date of purchase. For the first year, coverage is
provided for both parts and labor on warranty repair services. After the first
year, the Limited Lifetime Warranty covers parts only and does not cover labor
fees and Accessories Accessories such as straps and batteries are covered for
the first year only. All shipping fees incurred, the cost of accessories after
the first year, and labor fees associated with out-of-warranty repair work are
the customer’s responsibility.
Warranty
1-Year Warranty
The original purchaser for this unit is provided with a 1-YEAR Warranty. The
warranty begins on the date of purchase. For the first year, coverage is
provided for both parts and labor on warranty repair services. After the first
year, the Limited Lifetime Warranty covers parts only, and does not cover
labor fees and Accessories. Accessories such as straps and batteries are
covered for the first year only. All shipping fees incurred, the cost of
accessories after the first year, and labor fees associated with out-of-
warranty repair work are the customer’s responsibility.
Not Covered Under Warranty
We DO NOT offer a warranty for products that have been bought secondhand or
were resold. Issues of replacement and refunds on units purchased less than 30
days from an authorized dealer must be addressed to the dealer directly. If
the products purchased from an authorized dealer are after 30 days from the
date of purchase, please send the units to us for service and repair. We DO
NOT cover the cost of repairs and replacements due to misuse by the owner or
dog, improper maintenance, and/or lost units. The warranty is void if the unit
has been altered or an unauthorized person has damaged the unit while
attempting repair work.
Procedure for Repair Work
If the unit is malfunctioning, please refer to the “Troubleshooting” in the
manual before sending it back for service. A copy of the sales receipt showing
the purchase date may be required before warranty work is initiated. Please
include a brief explanation outlining the problem, and include your name,
address, city/state/zip code, daytime phone number, evening phone number, and
email address.
Compliance FCC-USA
This device complies with part 15 of the FCC rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference. (2) This device must accept any interference received, including
interference that may cause undesired operation.
CAUTION: Modification or changes to this equipment not expressly approved
by the manufacturer may void the user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/ TV technician for help.
Design By PAT PET
https://patpet.usl
service@patpet.com
@PATPET
1-855-888-9922
*Shenzhen Patpet Technology Co., Ltd Add No 59-63, The 2nd Industrial Park,
Housing, Shajing Street, Baoan District, Shenzhen, China
MADE IN CHINA**
Documents / Resources
|
PATPET P-COLLAR910 Dog Training
Collar
[pdf] User Manual
P-COLLAR910, PCOLLAR910, 2AHHYP-COLLAR910, 2AHHYPCOLLAR910, P-COLLAR910 Dog
Training Collar, P-COLLAR910, Dog Training Collar
---|---
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>