Gasmate EH240 Bar Table Electric Heater Instruction Manual

BAR TABLE ELECTRIC HEATER
Model No. EH240

Maximum output 1600W infrared heating elements
70cm Diameter tempered glass tabletop
Bar table height – 110cm
High-efficiency carbon fiber element
Stainless steel base
Safety tip-over switch
Suitable for outdoor entertaining areas
IP24 Approved

Important: Retain these instructions for future use
Gasmate® is a registered trademark of:
Sitro Group Australia Pty Ltd www.gasmate.com.au
Aber Living, N.Z www.gasmate.co.nz

IMPORTANT SAFEGUARDS

To reduce the risk of personal injury or damage to property, follow basic safety precautions when using this product, including the following:

READ THESE INSTRUCTIONS CAREFULLY BEFORE USING THE PRODUCT. KEEP THE INSTRUCTIONS HANDY FOR FUTURE REFERENCE.

Important: Always operate the Product from a power source of the same Voltage, Frequency, and Rating as indicated on the Product Identification Plate.

• Close supervision is necessary when any Electrical Product is used or operated near children or infirm persons; DO NOT leave the Product unattended when in use; young children should be supervised to ensure that they DO NOT play with the Product.
• DO NOT operate any product which has been/ or appears damaged in any manner or after the Product malfunctions, or is dropped.
• If it is necessary to use an Extension Cord with this Product, prior to its use, make sure the extension Cord is safe to use, capable of handling the electrical load of the Product (refer to Product Identification Plate), and has been checked and tested by your electricity supplier or qualified technician.
• DO NOT use this heater with a programmer, timer, or another device that switches the heater on automatically, since a fire risk exists if the heater is covered or positioned incorrectly.
• Always arrange the Cord so that it cannot be pulled or tripped over.
• DO NOT operate this Product immediately below an electrical Socket Outlet.
• Always ensure clearance of 1.5m to any wall or combustible surface.
• Avoid operating the Product on long pile carpets or uneven surfaces. Use only on flat, level, and stable surfaces.
• DO NOT disconnect the Product from the Power Supply by pulling on the Cord. Never move, carry or hang the Product by the Cord.
• DO NOT operate this Product in the presence of explosive and/or flammable liquid or fumes such as where aerosol (spray) products are being used or where oxygen is being administered.
• Avoid leaving the heater unattended when in use.
• Switch OFF and UNPLUG from Power Outlet when not in use, allow to cool before shifting the Product from one location to another, and before cleaning.
• When storing the Product, gently wind the Cord around the Cord Wrap if provided, otherwise loosely coil the cord. Avoid wrapping the Cord around the Product.
• DO NOT operate or place any part of this Product on or near any hot surfaces such as a gas flame, electric element, or near a heated oven, or let the cord hang over the edge of a table or bench.
• Avoid touching hot surfaces, use Handles or Knobs.
• Avoid contacting moving parts. Keep hands, hair, and clothing, well away from the Product while it is in operation.
• DO NOT use the Product for other than its intended use as described in these instructions. This Product is intended for Normal Domestic Household Use only.
• The power supply must be supplied through a residual device (RCD) having a tripping current not exceeding 30mA.
• Only connect this heater to a socket-outlet having earthing contact.
• DO NOT use the heater during inclement weather, rain, or damp conditions.
• DO NOT operate the heater with a damaged cord or plug, or if the heater malfunctions, or has been damaged in any manner.
• Never operate this heater when you are tired, drinking alcohol, taking drugs, or taking medication that causes drowsiness.
• This heater is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge unless they have been given supervision or instruction concerning the use of the heater by a person responsible for their safety.
• Pets and animals must be kept away from the work area so as to avoid tripping dangers.
• Always arrange the Cord so that it cannot be pulled or tripped over.
• Never modify this heater as damage and injury may occur, and this will void your warranty.
• Check for damaged parts before operating this heater.
• Keep the power cord away from heat, oil, solvents, and sharp edges.
• Check the power cord for signs of damage before each use. If damaged do not use it.
• The power cord must only be replaced by an authorized service facility.
• Use only a ‘3’ core (earth pin) extension cord with this heater.

BEFORE FIRST USE

UNPACK THE PRODUCT

• Carefully unpack the Product making sure you keep all the packing material until all the parts of the Product have been checked and the Product has been used. We recommend keeping all the packing material in a safe place for re-use at any time you wish to repack the Product for storage.
• To remove any dust that may have accumulated during unpacking, simply wipe the exterior of the Product with a clean, soft, slightly dampened (not wet) cloth, then allow it to thoroughly dry. Do not use any abrasive cleaners as they may scratch the surface.

SERVICE & SAFETY

• This Product is shipped to you in a factory-sealed carton. Should the Product be damaged, dropped, or malfunctions in any way, or its Flexible Cord is damaged, contact customer service or return it to the place of purchase.
• Always operate the Product as described in these instructions.

OPERATING INSTRUCTIONS

Note: This heater requires a 1.5m clearance on all sides.

1. Always operate a Free Standing Heater on a dry, stable, and level floor surface, well away from curtains, drapes, and soft furnishings. DO NOT operate this Product immediately below an electrical Socket Outlet.

2. Plug the Power Cord into a Power Outlet and turn Power Outlet ON

3. To turn the heater ON, rotate the knob
   O is off
   I is 800W (1 element)
   II is 1600W (2 elements)

4. To turn the heater OFF, rotate the knob to O
   Note: Knob can be rotated clockwise or anti-clockwise for easy use.

5. When unattended, we recommend you make sure the Product is turned OFF and DISCONNECTED from the Power Supply.

6. Be sure the Product is turned OFF, DISCONNECTED from the Power Supply, and allowed to cool before moving.

7. When storing the Product, loosely coil the cord. It is important to allow the Product to cool before storage.

TO TURN HEATER ON/OFF

IMPORTANT

• Always operate the Product from a power source of the same Voltage, Frequency, and Rating as indicated on the Product Identification Plate.
• Avoid any possibility of a fire hazard by never covering, positioning, or arranging any material near, or restricting the airflow of the Heater. This Heater is not intended to be used as clothes or a towel dryer.
• If used outdoors ensure the heater power cord is connected to an outdoor PowerPoint.
• The power supply must be supplied through a residual device (RCD) having a tripping current not exceeding 30mA.

Care & Cleaning

1. After each use, make sure the Product is turned OFF and DISCONNECTED from the Power Supply. Let the Product cool after use before moving, cleaning or storage.
2. Clean the exterior of the Product by wiping with a slightly dampened (not wet) soft cloth. Avoid the use of scouring pads, harsh detergents, solvents, polish, abrasive or aerosol cleaners as they may damage the surfaces of the Product. Dry with a clean, soft cloth before storage, or reconnecting to the Power Supply.
3. When storing the Product, loosely coil the Power Cord. Avoid wrapping the Power Cord around the Product. Store in a cool, dry place. NEVER move, carry or hang the Product by the Power Cord.

FOR YOUR SAFETY

• CAUTION: To reduce the risk of electric shock, DO NOT IMMERSE the Product in any liquid, or use the Product near baths, basins, swimming pools, shower areas,s, or other vessels containing water or other liquids, or when standing in or on damp or wet surfaces. If any Electrical product falls into water, UNPLUG it immediately; DO NOT REACH INTO THE WATER. Do not immerse or expose the Flexible Cord or Plug to rain, moisture, or any liquid.
• IMPORTANT: Prior to reconnecting the Power Supply, the complete Product should be inspected by a qualified technician.
• WARNING: To avoid overheating the Power Supply Cord, completely unwind all the cords, including from the cord storage area of the heater, if fitted.
• CAUTION: This product should not be used/operated in a confined space. Always use/operate this Product well away from walls and curtains. A fire may occur when this product is in operation, if it is covered, or is close to flammable materials, such as curtains, drapes or wall coverings, etc.
• CAUTION: To reduce the risk of shock or damage to the Product, DO NOT disassemble. No user-serviceable parts inside.
• CAUTION: DO NOT immerse the Product, its Flexible Cord Plugin water, or any other liquid.
• IMPORTANT: In some Products, the replacement by the user of the Flexible Cord is not intended. Special Tools are required to disassemble the Product or to replace the Cord, or a special Cord is required.

ELECTRICAL DATA

IMPORTANT
This product is fitted with a sealed electrical connection plug that is compatible with the heater, the main supply for Australia, and meets the requirements of international standards. This heater must be connected to a supply voltage that is equal to that stated on the rating label. If the mains connection plug or power cord becomes damaged it must be replaced with a complete assembly that is identical to the original, and this must be replaced by an authorized service center. Always follow the Australian requirements for connection to the mains supply. If in doubt always consult a qualified electrician.

TECHNICAL SPECIFICATION

Heater specifications can be found on the data label.

ASSEMBLY PREPARATION

1. Carefully unpack the Product making sure you keep all the packing material until all the parts of the Product have been checked and the Product has been used. We recommend keeping all the packing material in a safe place for re-use at any time you wish to repack the Product for storage. If you wish to dispose of the packaging material dispose of it in an environmentally responsible manner.
2. To assemble this Product you will require a “Phillips” head screwdriver.
3. We recommend that you lay a sheet or blanket on firm flat ground to assemble this Product.
4. Read this instruction manual fully and carefully before you start assembly. Keep this instruction manual in a safe place for the future if required.

PARTS LIST

ASSEMBLY

|
---|---
|

BASE ASSEMBLY FIG. A

1. Turn the Base upside down and attach both Wheels (5) and then screw in both Feet (1) and adjust them to the same level as the Wheels.

2. Turn the base the correct way up and place the Base Cover (9) on. Make sure the 3 holes in the Base Cover match the Base.

3. With the Base and Base Cover on its side push M8*120 through the Base, Base Cover. Now slide the Tube (10) over the screw. Now attach the Foot Ring (12) with this screw.

4. Repeat step 4 for the other 2 Tubes (10).
   HEATER ASSEMBLY FIG. B & FIG. C

5. Lay the Heater Body on its side next to the assembled base. Feed the power cord through the large hole in the assembled base.

6. Slide the heater body up to the assembled base and attached to the Base Bracket (3) and screw (2). Make sure the Base Brackets (3) match up with the holes on the Base Cover and assembled Base.

7. Pull the Power Cord out fully through the assembled base and clip it into the Cord Clip (15).
   GLASS TOP ASSEMBLY FIG. D

8. Stand the Heater up the right way on its base. If needed adjust the Feet (1) to stop the Heater rocking.

9. Place Glass Top (17) on top of the Heater Body. Make sure the screw holes on Table Mount (18) line up with the holes on top of the heater.

10. Attach the Glass Top onto the Heater with 4 Screws (M6*8) and Spring Washers ø6.2.

For any queries or assistance call

Customer Service
Australia Only
1300 174 876
Hours of operation: Monday to Friday 8.00 am – 5.00 pm EST
Email: sales@sitro.com.au
Do not return to a place of purchase.
Keep your purchase receipt, this will be required to make any claims under the 12-month warranty.

References

• Gas BBQs Kitchens Fires Heaters Camping | Gasmate NZ Outdoor Living
• Gas Burner BBQ Grill & Outdoor Kitchen Products | Gasmate

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>