ams AS8579 Adapter Board User Guide
- June 6, 2024
- ams
Table of Contents
ams AS8579 Adapter Board
Introduction
This manual explains how to use the AS8579-SS_EK_AB hardware. The Hardware is
designed to test and evaluate the features of AS8579 capacitive sensor. The
AS8579 is a sensor, which measures the capacitive value by separately
measuring the 10-bit Information (accumulated to 14-bit) of I and Q. This
14-bit information provides the capacitance of the application. The I and Q
data can be read over a standard SPI interface.
For first setting up, please see application note:
AS8579_SPI_Configuration_AN001003_1-00.
Kit Content
Figure 1:
AS8579 Adapter Board Kit Content
Ordering Information
Ordering Code | Description |
---|---|
AS8579-SS_EK_AB | AS8579 Adapter Board |
Board Description
The PCB can be connected via standard SPI to a microcontroller. The Production
Programmer from SD4Y and the ams I&P-Box are also recommended tools for
communication/programming interface.
If you want to connect the I&P box to the Adapter Board, a level shifter is
needed (the I&P Box works with 3.3 V voltage levels).
The PCB is equipped with all necessary peripheral components for easy
evaluation.
Figure 2:
AS8579 Adapter Board
Figure 3: BOM
Symbol | Description |
---|---|
U1 | Capacitive sensor AS8579 |
C1 | Capacitor 100 nF |
C2 | Capacitor 1 µF |
X1 | Oscillator 48 MHz |
Detailed Description
Figure 4:
AS8579 Adapter Board Overview Figure 5: Description
Components | Description |
---|---|
Supply | Pin 5 V supply and ground |
SPI Pins | Communication and Programming Interface |
SEN Lines | Sensing interface |
VAR/ FIX SEN | Pins for cable and PCB shielding |
Oscillator
| Oscillator for clock generation of system clock frequency input
Settings: EDIV=0000b (default value) -> CLK_E divider is 12 and resulting system clock is 4 Mz
AS8579| Capacitive sensor
Bypass Caps| Recommended decoupling capacitors
Pinout
Figure 6:
AS8579 Adapter Board Pinout
Figure 7: Pinout
Pin # | Symbol | Description |
---|---|---|
P1-1 | SEN0 | |
P1-2 | SEN1 | |
P1-3 | SEN2 | |
P1-4 | SEN3 |
Sensing Lines (0-7)
P1-5| SEN4|
P1-6| SEN5|
P1-7| SEN6|
P1-8| SEN7|
P1-9| 5V| 5 V supply
P1-10| GND| Ground
P1-11| CSn| SPI – Chip select
P1-12| MOSI| SPI – Master out slave in
P1-13| CLK| SPI – Clock
P1-14| MISO| SPI – Master in slave out
P1-15| SEN9|
Sensing Lines (8-9)
P1-16| SEN8|
P2-1| FIX_SEN| PCB shielding driver
P2-2| VAR_SEN| Cable shielding driver
Hardware
Schematic
Figure 8: Schematic
Layout
Figure 9: PCB Layout
Revision Information
Changes from previous version to current revision v1-00 | Page |
---|---|
Initial production version | all |
- Page and figure numbers for the previous version may differ from page and figure numbers in the current revision.
- Correction of typographical errors is not explicitly mentioned.
Legal Information
Copyrights & Disclaimer
Copyright ams AG, Tobelbader Strasse 30, 8141 Premstaetten, Austria-Europe.
Trademarks Registered. All rights reserved. The material herein may not be
reproduced, adapted, merged, translated, stored, or used without the prior
written consent of the copyright owner.
Demo Kits, Evaluation Kits and Reference Designs are provided to recipient on an “as is” basis for demonstration and evaluation purposes only and are not considered to be finished end-products intended and fit for general consumer use, commercial applications and applications with special requirements such as but not limited to medical equipment or automotive applications. Demo Kits, Evaluation Kits and Reference Designs have not been tested for compliance with electromagnetic compatibility (EMC) standards and directives, unless otherwise specified. Demo Kits, Evaluation Kits and Reference Designs shall be used by qualified personnel only.
ams AG reserves the right to change functionality and price of Demo Kits,
Evaluation Kits and Reference Designs at any time and without notice.
Any express or implied warranties, including, but not limited to the implied
warranties of merchantability and fitness for a particular purpose are
disclaimed. Any claims and demands and any direct, indirect, incidental,
special, exemplary or consequential damages arising from the inadequacy of the
provided Demo Kits, Evaluation Kits and Reference Designs or incurred losses
of any kind (e.g. loss of use, data or profits or business interruption
however caused) as a consequence of their use are excluded.
ams AG shall not be liable to recipient or any third party for any damages, including but not limited to personal injury, property damage, loss of profits, loss of use, interruption of business or indirect, special, incidental or consequential damages, of any kind, in connection with or arising out of the furnishing, performance or use of the technical data herein. No obligation or liability to recipient or any third party shall arise or flow out of ams AG rendering of technical or other services.
RoHS Compliant & ams Green Statement
RoHS Compliant: The term RoHS compliant means that ams AG products fully
comply with current RoHS directives. Our semiconductor products do not contain
any chemicals for all 6 substance categories plus additional 4 substance
categories (per amendment EU 2015/863), including the requirement that lead
not exceed 0.1% by weight in homogeneous materials. Where designed to be
soldered at high temperatures, RoHS compliant products are suitable for use in
specified lead-free processes.
ams Green (RoHS compliant and no Sb/Br/Cl): ams Green defines that in addition to RoHS compliance, our products are free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material) and do not contain Chlorine (Cl not exceed 0.1% by weight in homogeneous material).
Important Information: The information provided in this statement represents ams AG knowledge and belief as of the date that it is provided. ams AG bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties.
ams AG has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. ams AG and ams AG suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
- Headquarters
- ams AG
- Tobelbader Strasse 30 8141 Premstaetten Austria, Europe
- Tel: +43 (0) 3136 500 0
- Please visit our website at www.ams.com
- Buy our products or get free samples online at www.ams.com/Products
- Technical Support is available at www.ams.com/Technical-Support
- Provide feedback about this document at www.ams.com/Document-Feedback
- For sales offices, distributors and representatives go to www.ams.com/Contact
- For further information and requests, e-mail us at ams_sales@ams.com