Ancerre LEDM-Immersion-30 30 x 40 Inch LED Frameless Mirror Instruction Manual

June 6, 2024
Ancerre

Sancerre LEDM-Immersion-30 30 x 40 Inch LED Frameless Mirror

Installation Instructions

  • Please read and follow warm tips before installation!
  • & Power off electrical before installation. Use a voltage detector to make sure. Verify the circuit breaker is turned off & lock it in case someone tries to turn it on.
  • & If you’re NOT experimenting in installing electrical wiring, then hire a professional electrician. Your safety is more important than saving a few dollars.
  • .& Avoid water at all times when working with electricity. Never touch or install any electrical equipment or circuits with wet hands.
  • & Tools you will need a voltage tester, wire cutters, wire and cable strippers, needle nose pliers, continuity tester, and wire closure.
  • & Wear Safety Glasses and Protective Clothing to protect you from sparks
    Ancerre LEDM-Immersion-30 30 x 40 Inch LED Frameless Mirror
fig1

Installation manual

Ancerre LEDM-Immersion-30 30 x 40 Inch LED Frameless Mirror
fig12

  1. Step 02: Mark the punching position on the wall with a pencil. use a level gauge makes sure the hole at the same level.
  2. Check the wall.Make sure that the wall is bearing walls that can support the Mirror’s weight. Measure the width and height of the mirror back holes/hocks distance with a tape measure.
  3. use impact drill punch holes in the marked center (6-SMM drill bit),the drilling depth is about SCM.Use a hammer to drive the expansion screw into the drilled hole.Ancerre LEDM-Immersion-30 30 x 40 Inch LED Frameless Mirror 3
  4. Use screwdriver screw the screw into the expansion screw, tighten. And then leave a distance of about SMM from the wall.
  5. Use screwdriver screw the screw into the expansion screw, tighten. And then leave a distance of about SMM from the wall.

Front View

Back View

FEATURES

  • SMM Copper-free mirror.
  •  PVC film backed.
  •  Mounting type: Vertically.
  •  Energy Efficient and Long Lasting LED Lighting.
  • 1Year Limited Warranty on Electronic Components.

LIGHTING

  •  LED (Light-Emitting Diode).
  •  Defogger.
  •  Bluetooth
  •  Color Temperature: 2800 & 6000K.
  •  Power Source: Input: 11 0volts, 50/60HZ.
  •  IP44 rated.
  •  Brightness Lumen: 3520; Power Consumption :72Watts ;
  •  Energy saving LED lifetime approx 50,000 hours.
  •  UL certificated for electric power supply, defogger,  and LED strips.

Standard size

  • 24″x40″
  • 30″x40″
  • 36″x40″
  • 48″x40″

Operating instructions

Ancerre LEDM-Immersion-30 30 x 40 Inch LED Frameless Mirror
8

A.Turn on/off lighting & CCT adjusting
Short press button to start the light working. Then short touch button@(<l s) to switch the color Temperature 2800Kor 6000K. B.Defogger
Press button  the defogger sign will light up on the display and start working.
C.Bluetooth Speaker

  1. Press button will turn on the Bluetooth Speaker function; turn on the Bluetooth function on your device and search for “Ancerre design ” to connect. When connected successfully, the Bluetooth sign will light up on the display screen and the mirror will work as a speaker.

  2.  Press button® to pause /restart the speaker when you need to; short touch button for few seconds till the volume number starts flashing, press(Dand to increase or decrease the number.

  3.  Press(Dand  to choose the next/last songs during playing music
    .D.Reset the Time Year & Date

  4. . Hold button for few seconds to engage the time program mold until the minute number starts flashing. Press 0 or @ button to increase or decrease the number to the correct hour; then short press button to set minutes and once it worked, touch buttonto set the correct year as it is .

  5. . After the year settled down, repeat the step to reset the month and date accordingly.
    Care & Maintenance
    NOTE11 : Use warm soapy water and a soft, damp, lint-free cloth to clean the mirror. Wipe dry with another clean cloth . Glass cleaner can be used on the mirror surface when required . Avoid scourers, abrasives, and chemical cleaners as they can damage the glass and the frame.
    In hard water areas, limescale may deposit on the glass . Regular cleaning will minimize this problem. If this build-up becomes increasingly difficult to remove, apply a small amount of white vinegar on the area .

  • & Do not attempt to cut the glass.
  • & Do not hit the glass with hard or sharp articles.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals