bioby N1 Portable Bottle Warmer User Manual

bioby N1 Portable Bottle Warmer

Read this user manual carefully before using your portable bottle warmer, and save the user manual for future reference.

IMPORTANT SAFEGUARDS

Strangulation hazard! Keep out of reach of children. Do not use with extension cords.

When using electrical appliances, basic safety precautions should always be followed, including the following:

• Read all instructions carefully before using your bottle warmer.
• To protect against electrical shock, do not immerse the appliance, cord or plug in water or any liquid. Clean with damp cloth only. Avoid spillage on the connector.
• For use by adults for intended purposes only. Any other use is inappropriate and dangerous. Keep out of the reach of children.
• Appliance should be placed on a flat and stable area away from hot surfaces.
• Do not let cord hang over edge of table or counter or touch a hot surface.
• Do not move appliance when in use or if it contains hot water or liquid.
• The warming chamber may become hot. Do not touch while in use and let cool before handling.
• Ensure the baby bottle contents are at a safe temperature before feeding.
• Use plastic baby bottles approved for boiling or glass thermo-resistant baby bottles with this appliance.
• Do not use this product to heat frozen baby bottles.
• Unplug from outlet when not in use and before cleaning. Allow to cool before putting on or taking off parts. Allow warmer to cool before cleaning.
• Do not operate any appliance with a damaged cord or plug after the appliance malfunctions or has been damaged in any manner.
• The use of accessory attachments is not recommended by the appliance manufacturer and may cause injuries.
• Do not place on or near a hot gas or electric burner, or in a heated oven.
• Always attach plug to appliance first, then plug cord into the wall outlet. To disconnect, turn any control to “off” then remove plug from wall outlet.
• To disconnect, always make sure unit is “off” before removing plug from wall outlet.

PRODUCT & PARTS

Note:

This product has a built-in Ii-Ion battery. When the battery indicator red light is always on, we recommend that you use a certified 5V— 2A adapter to charge warmer motor as soon as possible.

INCLUDED ADAPTERS& SEALING RING

The adapter on the unit for : (Non-glass bottles with 53mm neck width)

• PHILIPS AVENT
• NUK

Adapters NUK for : (Bottles with 50mm neck width)

• NUK

Adapters MAM for: (Bottles with 53mm neck width)

• PHILIPS AVENT
• LANSINOH
• MAM

Adapters DR.BROWNS for: (Bottles with 56mm neck width)

• DR.BROWNS (Wide neck)

Tips: L-Shape Sealing ring

1. Each adapter has a built-in L-shaped sealing ring.
2. Before use, please check whether the sealing ring is installed properly. The sealing ring must be installed correctly on the side with the inner spiral pattern to avoid leaks.

WARNING:

Do not use glass baby bottle without an adapter.
*DR. BROWNS, PIGEON, NUK, MUNCH KIN, PHILIPS AVENT, COMBI, DOUBLEHEART, LANSINOH, MAM are trademarks of their respective owners.

Manufacturer:

HONG KONG TING HUI LIMITED

Address:

21/F.,Hing Lung Commercial Building,68-74 Bonham Strand, Sheuang Wan, Hong Kong

Made in China

INSTRUCTIONS

1. Choose the correct adapter for your baby bottle (see Included Adapters on Page 4).
   
   Ensure the L-rings are installed in the warmer unit and adapter (flat side down).
   Screw the adapter into the neck of the warmer unit. If no adapter is needed, screw bottle directly into the warming unit.

2. Place the warmer unit on the baby bottle.
   
   Turn the bottle warmer upside down and screw it onto the baby bottle or adapter. Twist until the baby bottle is pressed firmly against the L- ring to ensure a watertight seal.

3. Turn the bottle warmer right side up.
   

DISPLAY & OPERATION

1. Turn on the bottle warmer Make sure the bottle warmer place right as shown in the left picture. Long press the power button ” ”  to turn on the bottle warmer. It will start warming and the green light will flash.
   

2. Defrosting mode
   When the initial temperature is :S 68°F(20°C), it changes to unfreeze the liquid. The blue ” ” light will gradually flash. When the temperature reaches 86°F(30°C), it will automatically change to the 98.6°F(37°C) warming mode.
   

3. Warming mode
   There are 4 temperature levels : 98.6°F(37°C), 104°F{40°C) , 113°F(45°C) or 122°F(S0°C). Short press the power button ” ” to select the appropriate temperature. The green light will flash until warming finished.
   

4. Keeping warm mode After the warming is completed, the liquid will maintain at constant temperature and the indicator light is always green.

TIME FOR USE

Heating time

Note:

External power supply(2A adapter)is recommended to use when using the warmer at home.

Heating Reference Table: Time in below table is laboratory data. Actual time is different based on different use environment.

TROUBLE SHOOTING

Problem| Analyze/Possible cause /Cause of issue| Solution
---|---|---
Indicator flash| High fluid temperature triggers protection mechanism| Before starti11g heating . check whether the Tempe rat urge 1s higher than 50 degrees: 1f it is, plea se let it coo l d own before starti ng the much in e.
Fai lure to complete the enoug h heati ng| When the temperate re reaches the setting level. the green indicat or light will stop

flashing and always be on.

Green light flashy s to trigger dry burn protection| Check if there is liquid in the bott le and make sure the bott le has been proper ly installed on the milk warmer, the n restart the machine
Red lig h t blinking for the heating

p-ad dam age Low power

| Please contact the cu stomper service for product repair When the red lig h t of h e on/off button is always on, it is recommended to use a certified 5V – 2A ada pter to charge the milk warmer as soo n as poss. able.
Adapte rs cannot fit the bott le| Bott le neck is too wide and it does not fit the adap ters included in Product Packa ges.| Choose the correct bott le or the adapter fit for your bab y bott le (see Included Adapters on Page 4)
Long heating time| Low starting temperature of the fu ild| The heating term provided in this manual is a reference data for the heating t time under specific conditions. The actual heating time is influenced by a variety of  co nidation ns, such as ambient temperature, bottle Materia l, starting temperature, m1 lk volume, etc.
Low ambient temperature
Large liquid volume
Wrong choice of temperature level
Temperature Error| Low ambient temperature Large liquid volume Failure to complete the enough heating|

1. Please use this product in an environment of 50- 95°F(1O-35°C).
2. Properly rn crease the heating time when the liquid temperature is low and the volume is large.
3. Correctly select the temperature level according to the desired temperature.
4. When the liquid volume is too large or the liquid temperature is low, shake the bottle warmer after completing heating and wait for another 1 minute to make the liquid fully heated even ly before removing the bottle.

CLEANING & MENTENANCE

DAILY CLEANING

Always unplug unit and ensure that it is cool before cleaning. Do not use scouring pads, abrasives or solvents for cleaning; they may damage the appliance and its surface. Place the rubber plug back into the plug attachment to prevent water intrusion and cause electrical short during cleaning.

Bottle Warmer unit

Wipe all surfaces with a damp cloth or sponge using mild liquid soap, rinse with clear water. Allow to air-dry. Do not submerge unit in liquid.

Adapters and L-rings

Wash with mild liquid soap and rinse with clear water. Allow to air-dry. Always replace L- rings to their proper location (flat side down). Keep the cover on when not in use to keep heating plate clean.

DE-SCALE

De- scale your bottle warmer after every use to ensure residual deposits are removed from the heating plate and the silicone seal. To de-scale. mix 0.5oz (15ml) of white vinegar with 0.5oz. (15ml) of cold water and pour into the Warming Chamber. Allow liquid to stand in the unit until any deposits(limescale) have dissolved. Discard liquid and rinse with clear water, repeat “Clean Cycle” to remove any residual deposits.

NOTE: To avoid bacteria growth, perform “Clean Cycle” and”De-Scale” daily. Any other servicing should be performed by an authorized service representative.

FCC WARNING

The device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause undesired operation.

WARNING:

Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

NOTE:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to connect the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>