lavaudio DS601 Desktop Audio Decoder User Manual
- June 6, 2024
- lavaudio
Table of Contents
**lavaudio DS601 Desktop Audio Decoder User Manual
**
Lavaudio DS601 is a high-performance desktop DAC with USB, Coaxial, Optical, Bluetooth input and 3.5mm/RCA output. USB of DS601 supports up to PCM 32bit/768kHz and DSD512(Native). DS601 comes with complete digital volume control and OLED display, so it can serve as “DAC+Pre amplifier”. We believe that Lavaudio DS601 will bring you more HiFi music experience and fun.
Package Contents
A. DS601 audio DAC
B. Power adapter(optional) x1
C. DC power cableC.
D. USB cable E. User manual
Product Overview and Control Functions
Instructions
Instructions for use
- Plug in the DC power cable, then choose to connect DS601 with PC through the USB cable or connect with CD player through Coaxial cable.
- The RCA OUT can connect with a headphone amplifier, a power amplifier and other device. C) Adjust a proper volume, then you can enjoy HiFi music.
Note: For Windows users, the driver need to be installed when first using. Please refer to “DS601 Driver & Installation Guide” and “DS601- Player Foobar2000 & JR”.
System Setting Interface
-
Filter mode when playing PCM format, MODE1-MODE7.
MODE 1 : apodizing fast roll-off filter
MODE 2 : linear phase fast roll-off filter
MODE 3 : linear phase slow roll-off filter
MODE 4 : mininum phase fast roll-off filter
MODES 5 : mininum phase slow roll-off filter
MODE 6 : corrected mininum phase fast roll-off filter
MODE 7 : brick wall filter -
Bluetooth system settings
-
Screen saver settings Optional screen always on and automatic screen off
-
Factory data reset The default values of the system parameters of 1-3are: MODE1, Bluetooth on, Automatic screen off. Note: When entering the system parameter setting interface,it will automatically exit it if there is no operation after 10 seconds.
Specifications
USB input| 16bit/44.1kHz-32bit/768kHz
DSD64-DSD512(Native)
---|---
Optical/
Coaxial input| 16bit/44.1kHz-24bit/192kHz
Bluetooth input| AAC/SBC/APTX/APTX LL/APTX HD/LDAC
Power supply| DC5V/1A
Size| 115x115x25mm
Weight| 484g
Product Parameters
| Output Voltage | 2Vrms@OdBFS |
|---|---|
| THD+N | <0.0002%@1 kHz A-weighing |
| Noise | <2uVrms@A-weighing |
| Crosstalk | -112dB@1kHz |
| SNR | 122dB |
| Output Impedance | 100 |
Troubleshooting
| Troubleshooting | Cause Analysis | Solution |
|---|---|---|
| Noise when COAX / OP input | Signal format error or out of range | Check the |
input signal format
USB does not recognize| Incorrect USB connection| Check or replace the USB
cable
Computer USB port damaged| Change another interface
OS problem| Reinstall the OS
Driver problem| Reinstall driver
No sound when USB input| Computer volume is too low| Adjust volume
Intermittent when USB input| PC is busy and the machine is hung| Waiting for
computer recovery
USB input, pop sound| Software problem| Update motherboard drivers and system
patches
If you still have problem or question, please contact us
(support@ankbit.com)
Daily Use
- Never pull out the USB cable while connected to a computer and using the audio output.
- The output signal of this machine must not be grounded or shorted.
- Do not leave the machine in a high temperature and humid environment, let it in rain or drop it.
- Never open the case by youself.The machine should be repaired by 1Mii Service.
- This machine is intended for indoor use only.
The product driver and electronic file manual can be downloaded from www.1mii.com
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>