BRESSER F004396 BR-S COB LED LED Lights Instruction Manual

F004396 BR-S COB LED LED Lights
Instruction Manual

Art. No.
F004396/F004397/F004594/F004595/F004606/F004607

GENERAL WARNINGS

DANGER OF BODILY INJURY!
Do not use it in the presence of children or animals. Store out of reach of children and animals.
RISK OF MATERIAL DAMAGE!
Make sure that no one can trip over the connection cables of the device. The device could be knocked over.
Only use the recommended power cable or the recommended battery for the power supply!
The manufacturer accepts no liability for voltage damage caused by the use of an unsuitable power supply!
DANGER OF AN ELECTRIC SHOCK!
This device contains electronic parts that are powered by a power source (power adapter). Only use the device as described in the manual. Otherwise, you run the DANGER of
an ELECTRIC SHOCK.
Never bend, squeeze or pull power cables, connecting cables, extensions or connectors. Protect cables from sharp edges and heat.
Check this device, cables, and connections for damage before use.
Never attempt to operate a damaged device or a device with damaged electrical parts! Damaged parts must be replaced immediately by an authorized service agent.
Operate the device only in a completely dry environment and do not touch the device with wet or damp body parts.
RISK OF GLARE!
Make sure that people and animals do not look into the light. The high luminosity can cause glare to the eyes and afterimages. This impairment of vision can lead to accidents.
FIRE/EXPLOSION HAZARD!
Always place the device in such a way that it cannot tip over and ensure that it is stored in a reasonably safe place.

• Keep children and animals away from the device! They could knock the device over.
• Make sure that no one can trip over connection cables. The device could be knocked over.
• Do not expose the device to high temperatures. Do not short-circuit the device or dispose of it in the fire! Excessive heat and improper handling can cause short circuits, fires, and even explosions!
• Only use the recommended power supply

IMPORTANT NOTE!
Do not disassemble the device! In the event of a defect, please contact your dealer. They will contact the Service Center and can arrange the return of this device for repair if necessary. Disconnect the power supply by pulling the mains plug when the appliance is not in use, in case of a longer interruption of operation, and before any maintenance and cleaning work.
Place your device so that it can be disconnected from the power supply at any time. The power outlet should always be near your appliance and should be easily accessible, as the plug of the power cord serves as a disconnect device from the main supply.
To disconnect the unit from the mains, always pull the mains plug and never pull the cable!
Do not subject the device to excessive vibrations.
CE DECLARATION OF CONFORMITY
Bresser GmbH has issued a „Declaration of Conformity“ in accordance with applicable guidelines and corresponding standards. The full text of the CE declaration of conformity is available at the following internet address: www.bresser.de/download/BRS- COB/CE/BRSCOB_CE.pdf
UKCA DECLARATION OF CONFORMITY
Bresser UK Ltd. has issued a „Declaration of Conformity“ in accordance with applicable guidelines and corresponding standards. The full text of the UKCA declaration of conformity is available at the following internet address: www.bresser.de/download/BRS- COB/UKCA/BRSCOB_UKCA.pdf
Bresser UK Ltd. • Suite 3G, Eden House, Enterprise Way, Edenbridge, Kent TN8 6HF, Great Britain

WARRANTY & SERVICE

The regular guarantee period is 2 years and begins on the day of purchase. You can consult the full guarantee terms and details of our services at ww.bresser.de/warranty_terms.
Would you like detailed instructions for this product in a particular language? Then visit our website via the link below (QR code) for available versions.

http://www.bresser.de/warranty_terms

DELIVERY CONTENT (Fig. 1)
LED Light (A), remote control (B), power cable (C)

PARTS OVERVIEW

(Fig. 1)
LED LIGHT (A)

1. Slide for S-bayonet release
   When turned on, the brightness range is 10-100%

2. Notches for accessories with S-bayonet connector

3. LED Light source

4. Holes for accessory rod (e.g. for umbrella)

5. Handle

6. Control panel

7. LCD

8. Adjustment knob
   • Press to set desired channel (1-99)
   • Turn to set desired brightness (10-100%)

9. Fixing screw (tripod connection)

10. Vents

11. Power slider

12. Power connection socket

13. Locking screw (tilt joint)

14. Tripod connection
    REMOTE CONTROL (B)

15. LCD

16. Power knob

17. – knob

18. Menu knob

19. + knob

20. Battery compartment
    POWER CABLE (C)

21. Euro plug

22. C13 plug

ESTABLISHING THE POWER SUPPLY

1. Insert the C13 plug (22) of the power cable (C) into the power connection socket (12) on the LED light.
2. Insert the Euro plug (21) of the power cable (C) into the wall socket.

SWITCHING ON/OFF THE LED LIGHT

1. Establish the power supply for the device.
2. Slide the power slider (11) to the ‘ON’ position to switch on the device. The lighting is switched on with the settings of the last use.
3. Slide the power slider (11) to the ‘OFF’ position to switch off the device. The last settings made are retained until the device is switched on again.

Important: Disconnect the device from the power supply if it is not going to be used for a long period of time!
ADJUSTING THE BRIGHTNESS

1. Turn the adjustment knob (8) clockwise to increase the brightness.
2. Turn the adjustment knob (8) counterclockwise to decrease the brightness.

SETTING UP THE CHANNEL

1. Press the adjustment knob (8) several times until the desired channel is shown in the display.

Note: Make sure to set the same channel on the device as well as on the remote control. To control different devices at the same time, use the same channel for all devices. If you want to control more devices at different times, use a different channel for each device.
ADJUSTING THE TILT ANGLE

1. Hold the LED light and slowly loosen the locking screw for the tilt joint (13).
2. Move the light head to the desired position and tighten the locking screw (13) again hand-tight.

*MOUNTING ON A TRIPOD (optional)**

1. Loosen the fixing screw (9) for the tripod connection (14) so that the opening of the tripod connection is exposed.
2. Place the LED light with the opening on the spigot adapter of a tripod and tighten the fixing screw (9) firmly.

ATTACHING ACCESSORIES (optional)

• This LED light is equipped with two holes in the tilt head which can be used to attach optional accessories with a suitable rod (e.g. umbrella).
• This LED light also has an S-bayonet connection which can be used to attach optional accessories with suitable S-bayonet.

DISPOSAL

Dispose of the packaging materials properly, according to their types, such as paper or cardboard. Contact your local waste disposal service or environmental authority for information on the proper disposal.
Do not dispose of electronic devices in the household garbage! As per the Directive 2002/96/EC of the European Parliament on waste electrical and electronic equipment and its adaptation into German law, used electronic devices must be collected separately and recycled in an environmentally friendly manner.
In accordance with the regulations concerning batteries and rechargeable batteries, disposing of them in normal household waste is explicitly forbidden. Please make sure to dispose of your used batteries as required by law at a local collection point or in the retail market. The disposal of domestic waste violates the Battery Directive. Batteries that contain toxins are marked with a sign and a chemical symbol.
¹ Battery contains cadmium
² Battery contains mercury
³ Battery contains lead

TECHNICAL DATA

Service
Please contact the service center first for any questions regarding the product or claims, preferably by e-mail.
e-mail: service@bresseruk.com
*Telephone: +44 1342 837 098
BRESSER UK Ltd**
Customer Support
Suite G3, Eden House
Enterprise Way
Edenbridge, Kent TN8 6HF
United Kingdom

• Number charged at local rates in the UK (the amount you will be charged per phone call will depend on the tariff of your phone provider); calls from abroad will involve higher costs.

Bresser GmbH
Gutenbergstraße 2
46414 Rhede · Germany
www.bresser.de
Bresser UK Ltd.
Suite 3G, Eden House
Enterprise Way, Edenbridge,
Kent TN8 6HF, Great Britain
@BresserEurope
Errors and technical changes reserved.
Manual_F004396-F004397-F004594-F004595-F004606
-F004607_BR-S-COB-LED_en-nl-de_BRESSER_v062022a

References

• Bresser | Startseite | Expand Your Horizon mit BRESSER
• Bresser | Startseite | Expand Your Horizon mit BRESSER

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>