artika PDT-SWR Swirl LED Light Fixture Instruction Manual

Artika PDT-SWR Swirl LED Light Fixture

INSTRUCTION MANUAL

IMPORTANT: READ CAREFULLY AND KEEP.

INCLUDED

WHAT YOU WILL NEED…

CAUTION
If using a dimmer, it must be LED compatible.

IMPORTANT
The installer and/or user must read, understand and follow these instructions before installing the product. This product must be properly installed before it is used. If instructions are not followed, the manufacturer will not be held responsible for any problems or product malfunction. Failure to follow installation and/or operating instructions voids the warranty.
We recommend that this product be installed by a certifi ed electrician. In some states or provinces, it is
a legal requirement for this type of product to be installed by a certifi ed electrician, according to the electrical and building codes effective in the region where the unit is used.
This product is compatible with most LED dimmers

WARNING:
Risk of electrical shock. Turn off the breaker at the panel.

Switch off the main electrical supply from the fuse box/circuit breaker before installing the unit or doing any maintenance.
Do not use outdoor.

HEIGHT ADJUSTMENT

NOTE: It is recommended to make any major adjustments to the height of the light fi xture before installation.

1. With the power off, measure the distance from the ceiling to the bottom of where you would like your light fi xture to hang.
2. To retract the wire, gently push it into the light fi xture base (fi g. 1).
3. To extend the wire, push the metal collar while gently pulling the wire down (fi g. 2). When the metal collar is released, the wire will be fi xed into position.
4. Once the wire is at the desired length, turn the fi xture over and slide the plastic wire retainer up to the wire nut, to prevent the pendant from slipping down when in use.

WARNING:
Changes or modifi cations to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment

FCC

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. this device must accept any interference received, including interference that may cause undesired operation.

NOTE: This equipment has been tested and found to comply with the limits for Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio or television reception. However, there is no guarantee that interference will not occur in a particular installation. If this equipment causes harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Operation is subject to the following two conditions:

1. this device may not cause interference, and
2. this device must accept any interference, including interference that may cause undesired operation of the device.

WARNING:
Risk of electrical shock. Turn off the breaker at the panel.

STEP-BY-STEP INSTALLATION

1. Turn off power at the circuit breaker and the light switch. Ensure the power is off before continuing.

2. Install the mounting bracket on the junction box using the junction box screws (fi g. 3).

3. Attach the hook to the mounting bracket (fi g. 4).

4. Connect the white wire (N) from the light fixture to the white supply wire (N) from the junction box using a wire connector. Connect the black wire (L) from the light
   fixture to the black supply wire (L) from the junction box using a wire connector. Connect the ground wire (G) from the light fi xture to the ground supply wire (G) from the junction box using a wire connector.

5. Put the wires into the canopy.

6. Mount the canopy onto the mounting bracket and secure it with the canopy screw.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>