GDKES 606USG4 Smart Wi-Fi Wall Switch User Manual

June 6, 2024
GDKES

GDKES 606USG4 Smart Wi-Fi Wall Switch

Installation

Separate the upper and lower parts from the switch with a screwdriver.

Prepare for wiring

Attention : Neutral wire is required.

  1. Live Wire connects L” terminal.
  2. Bulb Wire connects “LI, 12, 13, LA” terminal.
  3. Neutral Wire connects “N” terminal [Attention: Neutral wire is required].
  4. gang connects “L1” terminal.
  5. gang connects “LI, L2” terminal.
  6. gang connects “L1, L2, L3” terminal.
  7. gang connects “L1, L2, L3, LA” terminal.

Caution: Please cut off the power before wiring

Fix the switch onto the wall

  1. Put the switch lower parts into switch box in the wall.
  2. Mount the two side screws.
  3. Install the upper top case (install from up above).
  4. Cover the upper top case into switch.
  5. Turn on electricity, and then LED light will be flashed quickly for configure.

Indicator light status

  1. The WIFI indicator light flash continuously and quickly.
    • The switch is currently on the status of configuring with mobile phone APP.
  2. The WIFI indicator light flash 1 time every 3 seconds.
    The switch is into AP configure Mode.

How to download App?
Scan the QR code below or search Smart Life in IOS APP store or Google play.

Setting Smart Life APP

How to Register and Login

  1. Download or Scan the QR Code and install Smart Life App.
  2. Once download or Scan the QR Code, the App will ask you to register your device
  3. Enter your phone number or email which you prefer and select the country you live ein.
  4. Obtain verification code.
  5. Enter verification code
  6. Set Password.
  7. Create family.
  8. Enter the family name and select the room.
  9. Family create sucessfully.

How to add a new device in quick connection?

  1.  WIFl version and APP connect to network.

  2. Connect the switch with power.

  3. Hold the switch power button for 5-8 seconds, Wi-Fi indicator flashes quickly, The Wi-Fi indicator blinks twice a second.

  4. Open App and tap “Add Device or upper right corner+” and select “Wi-Fi switch to add.

  5. Please make sure power on the device and indicator light rapidly blinks at 2 time per second.

  6. confirm indicator rapidly blink

  7. Select Wi-Fi network, input Wi-Fi password, and confirm that will prompt to connection.

  8. Once connected the app will prompt to connection.

  9. Rename the device and select the room then tap Completed.
    ( Attention: The name should use numeric and letters, don’t use special symbols.)

  10. Long press switch to edit switch name.
    (Attention: The name should use numeric and letters, don’t use special symbols.)

Adding a New Device in AP Mode

  1. “Wi-FI” switch and APP configure network.
  2. Connect the switch with power.
  3. Hold the switch power button for 5-8 seconds, Wi-Fi indicator flashes quickly
  4. Hold the switch again for 5-8 seconds, Wi-Fi indicator flickers slowly, The Wi-Fi indicator flashes three times per second.
  5. Press “+” in the main menu of APP and select “Wi-Fi switch” to add
  6. Tap” AP Mode ” and “Confirm indicator slowly blink”
  7. Select Wi-Fi and input Wi-Fi password, press “Next”.
  8. Press “Reconnet”.
  9. Select “SmartLife-XXXX” and tap “CONNECT”.
  10. After connected “SmartLife-XXXX”tap the” “.

Warning:
This device complies with Part 15 of the FCC Rules. Operation is subjcct to the following two conditions: ()this device may not cause harmful interference, and 2) this device must accept any interference received, including interference that may cause undesired operation. changes or modifications not expressly approved by the party responsable for compliance could void the user’s authority to operate the cquipment.

FCC Rules

NOTE: This cquipment has becn testod and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.

These limits are desugncd to provide reasonable protection against harmful interterence in a residential installation. This cquipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause hamful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. lf this equipment does cause harmful interference to radio or television reception, which can be determined by turning the cquipment off and on, the user is cncouraged to try to corret the interference by onc or more of the following measurcs:

  • Reorient or relocate the receiving antenna
  • Increase the separation between the cquipment and receiver
  • Connect the cquipment into an outlet on a circuit different from that to which the receiver is connected
  • Consult the dealer or an experienced radioTV technician for helpP

NOTE: This device and its antenna(s) must not be co-located or operation in conjunction with any other antcnna or transmiticr RF Exposure Statement To maintain compliance with FCC’s RF Exposure guidelincs, This cquipment should be nstalled and opcrated with minimum distance of 20Cm the radiator your body. This de and its antenna(s) must not be co-located or operation in conjunction with any o antenna or transmitter

Read User Manual Online (PDF format)

Loading......

Download This Manual (PDF format)

Download this manual  >>

Related Manuals