Guangdong Gdkes Electric Technology Development 607USG4 Smart Wi-Fi Wall Switch User Manual
- June 6, 2024
- Guangdong Gdkes Electric Technology Development
Table of Contents
Guangdong Gdkes Electric Technology Development 607USG4 Smart Wi-Fi Wall
Switch User Manual
1. Installation Separate the upper and lower parts from the switch by
screwdriver.
2. Prepare for wiring Attention: Neutral wire is required.
2.1 Live Wire connects “L” terminal. 2.2 Bulb Wire connects “Ll, L2, L3, IA”
terminal. 2.3 Neutral Wire connects “N” terminal [Attention: Neutral wire is
required].
1 gang connects “LI” terminal.
2 gang connects “LI, L2” terminal.
3 gang connects “LI, L2, L3” terminal.
4 gang connects “LI, L2, L3, L4” terminal.
Caution: Please cut off the power before wiring.
{ 3. Fix the switch onto th wall
3.1 Put the switch lowirr parts into switch box in the wall .
3.2 Mount the two side screws .
3.3 Install the upper top case (install from up above).
3.4 Cover the upper top case into switch .
3.5 Turn on electricity, and then LED light will be flashed quickly for
configure.
Indicator light status:
- The WIFI indicator light went out. – The switch is not connected to the network .
- The WIFI indicator light flash continuously and quickly. – The switch is currently on the status of configuring with mobile phone APP.
- The WIFI indicator light flash 1 time every 3 seconds. – The switch is into AP configure Mode.
- The WIFI indicator light on. – The switch is connected to the network .
How to download App?
Scan the QR code below or search Smart Life in IOS APP store or Google play.
Setting Smart Life APP How to Register and Login
-
Download or Scan the QR Code and install Smart Life App.
-
Once download or Scan the QR Code, the App will ask you to register your device.
-
Enter your phone number or email which you prefer and select the country you live in.
-
Obtain verification code .
-
Enter verification code.
-
Set Password.
-
Create family. 8. Enter the family name and select the room .
-
Family create successfully.
How to add a new device in quick connection?
-
WIFI version and APP connect to network .
1.1 Connect the switch with power.
1.2 Hold the switch power button for 5-8 seconds, Wi-Fi indicator flashes quickly, The Wi-Fi indicator blinks twice a second.
1.3 Open App and tap “Add Device or upper right corner +” and select “Wi-Fi switch” to add.
1.4 Please make sure power on the device and indicator light rapidly blinks at 2 time per second. -
Confirm indicator rapidly blink .
-
Select Wi-Fi network, input Wi-Fi password, and confirm that will prompt to connection.
-
Once connected the app will prompt to connection .
-
Rename the device and select the room then tap Completed . (Attention: The name should use numeric and letters, don’t use special symbols.)
-
Long press switch to edit switch name. (Attention: The name should use numeric and letters, don’t use special symbols.)
Adding a New Device in AP Mode
-
“Wi-Fi” switch and APP configure network.
1.1 Connect the switch with power.
1.2 Hold the switch power button for 5-8 seconds, Wi-Fi indicator flashes quickly.
1.3 Hold the switch again for 5-8 seconds, Wi-Fi indicator flickers slowly, The Wi-Fi indicator flashes three times per second.
1.4 Press “+” in the main menu of APP and select “Wi-Fi switch” to add . -
Tap” AP Mode ” and “Confirm indicator slowly blink”
-
Select Wi-Fi and input Wi-Fi password, press “Next”.
-
Press “Reconnet”.
-
Select “SmartLife-XXXX” and tap “CONNECT”.
-
After connected “SmartLife-XXXX”,tap the ” F “.
Read More About This Manual & Download PDF:
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>