CUSTOM 5394220 Silk Android Touch Screen Monitor

CUSTOM 5394220 Silk Android Touch Screen Monitor

BOX CONTENTS

Remove the device from its carton being careful not to damage the packing material so that it may be re-used if the device is to be transported in the future. Make sure that all the components illustrated below are present and that there are no signs of damage. If there are, contact customer service.

1. Documentation (Short guide)
2. Device
3. Power supply cable
4. Power supply

DEVICE DESCRIPTION

1. ON/OFF key
2. Status LED
3. Support
4. Touch screen
5. USB 2.0 port (x5)
6. Serial DB9 port
7.  Reserved Debug port
8. Ethernet port
9. RJ48 port
10. Cash drawer port
11. MiniSD slot
12. Jack audio port
13. Power supply port

TURN THE DEVICE ON/OFF

1. Connect the power supply cable (included) to the device and the mains outlet use the type of electrical power supply indicated on the device label.
2. Turn the device on pressing the ON/OFF key.
   ATTENTION: In special conditions of use, it is recommended to mount ferrite on the power supply cable.

STATUS MESSAGES

Status LED

• DEVICE ON
• DEVICE OFF

CONNECTIONS

CLEANING

1. Disconnect the power supply cable and wait a few minutes to allow the screen to get to room temperature.
2. To clean the device use compressed air or a soft cloth.
3. Gently wipe the screen with a soft cloth slightly moistened with water.

TECHNICAL SPECIFICATIONS

DEVICE DIMENSIONS

All the dimensions shown in the following figures are in millimeters.

• Width: 397.80 mm
• Length: 204.50 mm
• Height: 330 mm
• Weigh:   4150 g

TECHNICAL SERVICE

1. Find the product label located on the bottom of the device. The label shows the product code PC, serial number SN and hardware release HW.
2. Login to the site www.custom4u.it, and use the support tools.

CUSTOM S.p.A.
Via Berettine 2/B
43010 Fontevivo (PARMA) – Italy

• Tel. : +39 0521-680111
• Fax : +39 0521-610701
• http:www.custom.biz

Customer Service Department:
www.custom4u.it
© 2020 CUSTOM S.p.A. – Italy. All rights reserved. Total or partial reproduction of this manual in whatever form, whether by printed or electronic means, is forbidden. While guaranteeing that the information contained in it has been carefully checked, CUSTOM S.p.A. and other entities utilized in the realization of this manual bear no responsibility for how the manual is used.
Information regarding any errors found in it or suggestions on how it could be improved is appreciated. Since products are subject to continuous check and improvement, CUSTOM S.p.A. reserves the right to make
changes in the information contained in this manual without prior notice cation.
The pre-installed multimedia contents are protected from Copyright CUSTOM S.p.A. Other company and product names mentioned herein may be trademarks of their respective companies. Mention of third-party products is for informational purposes only and constitutes neither an endorsement nor a recommendation. CUSTOM S.p.A. assumes no responsibility with regard to the performance or use of these products.

NOTE: THE IMAGES USED IN THIS MANUAL ARE USED AS ILLUSTRATIVE EXAMPLES. THEY COULDN’T REPRODUCE THE DESCRIBED MODEL FAITHFULLY.
UNLESS OTHERWISE SPECIFIED, THE INFORMATION GIVEN IN THIS MANUAL IS REFERRED TO ALL MOD-ELS IN PRODUCTION AT THE ISSUE DATE OF THIS DOCUMENT.

GENERAL INSTRUCTIONS

CUSTOM S.p.A. declines all responsibility for accidents or damage to persons or property occurring as a result of tampering, structural or functional modii cations, unsuitable or incorrect installations, environments not
in keeping with the equipment’s protection degree or with the required temperature and humidity conditions, failure to carry out maintenance and periodical inspections, and poor repair work.

GENERAL SAFETY INFORMATION

Your attention is drawn to the following actions that could compromise the characteristics of the product:

• Read and retain the instructions which follow.
• Follow all indications and instructions given on the device.
• Make sure that the surface on which the device rests is stable. If it is not, the device could fall, seriously damaging it.
  • Make sure that the device rests on a hard (non-padded) surface and that there is sufficient ventilation.
  • Do not i x indissolubly the device or its accessories such as power supplies unless specifically provided in this manual.
• When positioning the device, make sure cables do not get damaged.
• [Only OEM equipment] The equipment must be installed in a kiosk or system that provides mechanical, electrical, and I re protection.
• The mains power supply must comply with the rules in force in the country where you intend to install the equipment.
• Make sure that there is an easily-accessible outlet with a capacity of no less than 10A closely to where the device is to be installed.
• Make sure the power cable provided with the appliance, or that you intend to use is suitable with the wall socket available in the system.
• Make sure the electrical system that supplies power to the device is equipped with a ground wire and is protected by a differential switch.
• Before any type of work is done on the machine, disconnect the power supply.
• Use the type of electrical power supply indicated on the device label.
• These devices are intended to be powered by a separately certified power module having a SELV, non-energy hazardous output.(IEC60950-1 second edition).
•  [Only POS equipment] The energy to the equipment must be provided by a power supply approved by CUSTOM S.p.A.
• Take care the operating temperature range of equipment and its ancillary components.
• Do not block the ventilation openings.
• Do not insert objects inside the device as this could cause short-circuit-ing or damage components that could jeopardize printer functioning.
• Do not carry out repairs on the device yourself, except for the normal maintenance operations given in the user manual.
• The equipment must be accessible on these components only to trained, authorized personnel.
• Periodically perform scheduled maintenance on the device to avoid dirt build-up that could compromise the correct, safe operation of the unit.
• Do not touch the head heating line with bare hands or metal objects. Do not perform any operation inside the printer immediately after printing because the head and motor tend to become very hot.
• Use consumables approved by CUSTOM S.p.A.

THE CE MARK AFFIXED TO THE PRODUCT CERTIFIES THAT THE PRODUCT SATISFIES THE BASIC SAFETY REQUIREMENTS.

The device is in conformity with the essential Electromagnetic Compatibility and Electric Safety requirements laid down in Directives 2014/30/EU and 2014/35/EU inasmuch as it was designed in conformity with the provisions laid down in the following Standards:

• EN 55032 (Limits and methods of measurements of radio disturbance characteristics of Information Technology Equipment)
• EN 55024 (Information Technology Equipment – Immunity characteristics – Limits and methods of measurement)
• EN 60950-1 (Safety of information equipment including electrical business equipment)

The device is in conformity with the essential requirements laid down in Directives 2014/53/EU about devices equipped with intentional radiators
The Declaration of Conformity and other available certifications can be downloaded from the site www.custom4u.it.

GUIDELINES FOR THE DISPOSAL OF THE PRODUCT

The crossed-out rubbish bin logo means that used electrical and electronic products shall NOT be mixed with unsorted municipal waste. For more detailed information about recycling this product, refer to the instructions of your country for the disposal of these products.

• Do not dispose of this equipment as miscellaneous solid municipal waste, but arrange to have it collected separately.
• The re-use or correct recycling of electronic and electrical equipment (EEE) is important in order to protect the environment and the wellbeing of humans.
• In accordance with European Directive WEEE 2012/19/EU, special collection points are available to which deliver waste electrical and electronic equipment and the equipment can also be handed over to a distributor at the moment of purchasing a new equivalent type.
• The public administration and producers of electrical and electronic equipment are involved in facilitating the processes of the re-use and recovery of waste electrical and electronic equipment through the or-ganisation of collection activities and the use of appropriate planning arrangements.
• Unauthorized disposal of waste electrical and electronic equipment is punishable by law with the appropriate penalties.

FCC WARNING

This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions:

1.  this device may not cause harmful interference, and
2. this device must accept any interference received, including interference that may cause undesired operation.

Changes or modii cations not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

RADIATION EXPOSURE STATEMENT

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 cm between the radiator and your body.

CUSTOM S.p.A.
World Headquarters
Via Berettine, 2/B – 43010 Fontevivo, Parma ITALY Tel. +39 0521 680111 – Fax +39 0521 610701 info@custom.biz – www.custom.biz

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>