GiVi TN9056 Engine Guards Installation Guide
- June 15, 2024
- Givi
Table of Contents
GiVi TN9056 Engine Guards
Product Information
- Product Model: TN9056 – KN9056
- Product Name: ROYAL ENFIELD HNTR 350 (2022)
Features
- Paramotore – Engine Guard
- Pare-carter – Sturzbuegel
- Defensa De Moto – Paramotor
- Vite – Screw
- Vis – Schraube
- Tornillo – Parafuso
- TES M10x140
- TE M10x230
- TCE M10x180
- Rondella – Washer
- Rondelle – Scheibe
- Rondella Inox – Stainless Steel Washer
- Distanziale – Spacer
- Entretoise – Distanzstueck
- Dado Autobloccante M10
- Tappo – Cap
- Fiche – Stecker
- Componenti Originali – Original Parts
- Parties Originales – Original Bauteile
- Componentes Originales – Componentes Originais
Specifications
- Codice/Code: TN9056DXV TN9056SXV 10140TES 10230TE 10180TCE 1025RON 101RON C24L18F10,5T C22L6F10,5T 10DADIB 17COP
- Quantity: 2 (Right; Left) 1 1 1 9 1 4 4 2 4
Product Usage Instructions
- Mounting Instructions
- Remove the screws marked with “11” on both the left and right sides.
- Cut the specified length of the screw according to the chart.
- Disconnect any connections that may be attached.
- Remove the specified parts marked with “11” on both the left and right sides.
- Tighten the screws with a torque of 49Nm on both the left and right sides.
Screw Length Chart
- The following screw lengths are required for mounting the product:
| Screw | Length |
|---|---|
| M10x140mm | 8mm |
| M10x180mm | 12mm / 17mm |
| M10x230mm | 12mm / 17mm |
Tightening Torque
- The specified tightening torque for all screws is 49Nm.
FAQ (Frequently Asked Questions)
-
* **Q:** What should I do if there is a thread locker on the original screws?- A: If there is a thread locker on the original screws, use a threadlocker when mounting the accessory.
PARTS DESCRIPTION
| NO | Description | Features | Code | Quantity |
|---|---|---|---|---|
| 1 | Engine Guard Pare | – | TN9056DXV TN9056SXV | 2(Right; Left) |
| 2 | Screw Vis | TES M10x140 | 10140TES | 1 |
| 3 | Screw Vis | TE M10x230 | 10230TE | 1 |
| 4 | Screw Vis | TCE M10x180 | 10180TCE | 1 |
| 5 | Washer Rondelle | Foro Ø10,5mm / Esterno Ø25mm / Sp.2mm | 1025RON | 9 |
| 6 | Stainless Steel Washer Rondelle Inox | Foro Ø10mm / Sp.1mm | 101RON | 1 |
| 7 | Spacer Entretoise | Ø24×18 Foro 10,5mm | C24L18F10,5T | 4 |
| 8 | Spacer Entretoise | Ø22×6 Foro 10,5mm | C22L6F10,5T | 4 |
| 9 | Bolt | Dado Autobloccante M10 | 10DADIB | 2 |
| 10 | Cap Fiche | – | 17COP | 4 |
| 11 | Original Parts Parties Originales | – | – | – |
If there is thread locker on the original screws, use thread locker when mounting the accessory.
INSTALLATION
©Copyright 4/04/2023 LF-Rev00
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>