PARKSIDE PHZ 3 A1 Hammer Pull Bar Instruction Manual
- June 5, 2024
- PARKSIDE
Table of Contents
PHZ 3 A1 Hammer Pull Bar
HAMMER PULL BAR
Operating instruction
Introduction
Information about these operating instructions
Congratulations! You have purchased a high-quality product. Familiarise
yourself with the product before using it for the first time. To do this, read
the following operating instructions thoroughly. Use the product only as
described and for the range of applications specified. Keep these operating
instructions in a safe place. Please also pass these operating instructions on
to any future owner(s).
Proper use
The product is used exclusively for the joint-free bonding of laminate and parquet flooring and replaces the need for hammers, mallets and pull bars. The product can be used for all material thicknesses from 7 to 13 mm. Commercial or industrial use is not permitted. No liability will be assumed in cases of improper use. No liability will be assumed for damage caused by misuse or improper handling, the use of force or unauthorised modification. The risk is borne solely by the user.
Safety
Check the product before every use to make sure it is in perfect condition. Do not use the product if it is damaged in any way.
Do not allow children to use the product unless they are being supervised. Children are not always able to correctly recognise potential dangers. This product is not a toy.
This product is not intended for use by individuals (including children) with reduced physical, sensory, or mental capabilities. It may also not be used by individuals who lack experience and/ or knowledge unless they are supervised by a person responsible for their safety or have received instructions on how to use the product from such a person.
Use protective equipment. For your own safety, always wear ear muffs, a breathing mask/dust mask, safety goggles and safety gloves.
Warning! Risk of crushing! A jerking movement is necessary when using the product. Make sure that you do not injure yourself.
Rusty discolorations or other signs of chemical or mechanical change to the parts can cause premature failure of the parts.
Package contents
- Hammer Pull Bar
- These operating instructions
NOTE
► Check the package for completeness and signs of visible damage.
► If the delivery is incomplete or damage has occurred as a result
of defective packaging or during transport, contact the customer service
hotline (see section Service).
Use
NOTE
The product can be used for all material thicknesses from 7 to 13 mm.
With the help of the product, you can join laminate and parquet boards without
joints and without the need for hammers, tapping wood and pull bars. The
integrated pull bar transfers the force to the edge of the board when pulling
the carriage towards the rear stop. The product is particularly suitable for
the last row of boards by the wall.
♦ Place the pull bar on a board.
♦ Loosen the black locking screw on the carriage so you can move
the carriage.
♦ Hold the back stop with one hand to stabilize the product.
WARNING! RISK OF CRUSHING!
► Be careful not to hurt your fingers when moving the carriage forwards or
backwards.
♦ Hold the red handle firmly with your other hand and push the carriage
towards the pull bar as a starting position.
♦ Pull the red handle towards the rear stop. The board is joined seamlessly.
♦ If the board is not joined seamlessly, repeat the process with more force.
♦ After use, tighten the black locking screw on the carriage to prevent
unintentional movement of the carriage.
Cleaning and storage
ATTENTION! PROPERTY DAMAGE!
► Do not use aggressive or abrasive cleaning agents, as these can damage the
surfaces of the product.
♦ Clean the product using a dry cloth.
♦ Store the product in a clean, dry location away from direct sunlight.
Disposal
Dispose of the product via an approved waste disposal company or your
municipal waste disposal facility. Comply with all applicable regulations.
Please contact your waste disposal facility if you are in any doubt. Your
local community or municipal authorities can provide information on how to
dispose of the worn-out product.
The product is recyclable, subject to extended producer responsibility and is
collected separately.
Dispose of the packaging in an environmentally friendly manner. Note the labelling on the packaging and separate the packaging material components for disposal, if necessary. The packaging material is labelled with abbreviations (a) and numbers (b) with the following meanings: 17: plastics, 2022: paper and cardboard, 8098: composites.
Service
Service Great Britain Tel.: 0800 404 7657 E-Mail: kompernass@lidl.co.uk
Service Ireland Tel.: 1890 930 034 (0,08 EUR /Min., (peak)) (0,06 EUR /Min.,
(off peak)) E-Mail: kompernass@lidl.ie
IAN 364230_2010
Importer
Please note that the following address is not the service address. Please use
the service address provided in the operating instructions.
KOMPERNASS HANDELS GMBH BURGSTRASSE 21 44867 BOCHUM GERMANY www.kompernass.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>