HYSEN HY02B05RF Wireless Heating Thermostat User Manual
- June 2, 2024
- HYSEN
Table of Contents
HYSEN HY02B05RF Wireless Heating Thermostat
Product Specifications
- Power Supply: Receiver:230Vac 50/60HZ
- Transmitter: 2AA* 1.5V alkaline batteries
- Range of temperature display: 0~40°C
- Display accuracy: 0.5°C
- Insulating condition: Normal environment
- Probe sensor: NTC(10k)1%
- Running program: Set per 1 week as a cycle
- Contact capacity: 5A/250V(BW;WW);16A/250V(WE)
- Output: Switch relay
- Working environment temperature: 0~70°C
- Installation: Wall mounted or on battery seat
- Range of temperature adjustment: 5~35°C
- Size(mm)：868627
Operation Key
Icon Instruction
Programmable Mode Setting
Power on state, long press “ ” enter into first time period (hour setting), press to adjust value, short press “ ” enter into minute setting, press to adjust value, then short press “ ” enter into temperature setting, press to adjust value, successively short press “ ” to set second time period, thirdly time period ……
Advanced options
Power off state, long press for 3-5 seconds to access advanced setting A.
From A1 to Ao, short press to choose the option, and adjust data by After
finish setting , remain about 10 seconds,it will save setting and exit
advanced setting automatically.
| NO | Setting Options | Data Setting Function | Factory Default |
|---|
A1
| Measure Temperature Calibration| -9-+9℃
press ,
|
to adjust.
| | Display measuring temperature
A2| Temperature control difference setting| return| 0.5-5℃| 1℃
A3| Children lock setting| 0:half lock| | 1:full lock| 0
A4
|
Power off Memory
| 0: Last State
1: Electricity turn off 2: Electricity turn on
| 0
A5
|
Weekly programming selection
| P1: 5+2
P2: 6+1
P3: 7
| P1
A6| Setting temperature lowest limit| 1-10℃| 5℃
A7| Setting temperature highest Limit| 20-70℃| 35℃
A8
|
Anti-freezing function
| 1: 1-10℃
2: more than 10℃ ,display — ,then mean closed this function
|
5℃
A9
| Highest temperature protection function| 1: 20-70℃
2: less than 20℃,display –,then mean closed this function
| —
AA| Return different temperature of
High temperature protection
| 1-9℃| 2
---|---|---|---
Ao| Restore factory defaults| Display A o, long press until show
the whole screen
|
Power off state, long press for 3-5 seconds to access advanced setting B.
From PH to BO, short press to choose the option, and adjust data by After
finish setting ,remain about 10 seconds ,it will save setting and exit
advanced setting automatically .
NO| Setting Options| Data Setting Function| Factory
Default
---|---|---|---
PH| IP code high setting| 00-FF| 00
PL| IP code low setting| 01-FF| 01
BS
|
Write transceiver IP address
| Power on RF Receiver（the orange LED is steady on) ,continue press until Display”55” means IP match successfully.|
00
BN| Sensor function| N1: internal sensor
N3: internal and external sensors
| N1
Bo| Product information| Cannot be changed|
Description of temperature thermostat data communication
- Communicate with the receiver every 20 minutes under normal working conditions.
- Press the switch button to communicate with the receiver once.
- Communicate with the receiver once when the output state is switched.
On when wireless communication is normal, and blinking when wireless communication is abnormal
Transceiver tips
Receiver LED display instruction:
Power light (green light):it’s bright when power on Signal light(orange
light):it’s bright within 10s after power on (match IP),signal light off when
it receive match, signal light is blinking within 10s after power off.
Load light/fault light (red light):
- A、When no fault: light bright when load output, light off when no load output
- B、When fault: 1. Light blink 2 times indicates IP is fault
- 2. Light blink 3 times indicate it does not receive wireless signal for 1 hour
- 3. Light blink 4 times indicate built-out sensor is fault(only for a receiver with external sensor ) Sensor fault display: please choose correct working way of a built-in and external sensor, if choose wrongly or sensor fault (breakdown), “E1” or “E2” will be displayed on the screen. The thermostat will stop heating until the fault is eliminated.
Wiring Diagram
Cautions on Installation and Use
-
To prevent the thermostat display from a high fluctuation, special treatment has been made to the program. Therefore,
normally, the thermostat cannot immediately display the sudden change of temperature. -
The thermostat was installed on 1.5m above the ground.
-
For the thermostat installed, please take care not to install it to the wall corner, door/window side or behind the door or in such unheated area as exterior wall. Avoid hot / cold air duct, radiator, flue or thermal pipe.
-
If you have any problem for the installation,please contact our company hysen, we will make a demonstration for you
-
Only professional technicians are permitted to open the transmitter and receiver box of the thermostat for installation. When install the power supply, make sure that the power cable is well insulated.
-
The thermostat is unrepairable product. The user shall not open the internal circuit board.
-
Before installing the thermostat, make sure that the system is disconnected. The maximum voltage of the system shall meet the requirements specified in the Instruction Manual (Max. AC Voltage: 240V).
Warranty：
We offer the warranty of 18 months, from the sales day. The products of our
company can have lifetime warranty ,if it is not the quality problems, or
beyond the warranty period, we will charge for the after-sale service.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>