mijia MIZ-1Z Smart Lift Foot Bath User Manual
- June 17, 2024
- Mijia
Table of Contents
mijia MIZ-1Z Smart Lift Foot Bath
Please read this manual carefully before using the product and keep it properly.
Prohibit
- It is strictly forbidden to turn on the constant temperature function when there is no water. If you accidentally turn on the constant temperature function when there is no water, please turn it off immediately.
- It is strictly prohibited to turn on the lifting function when there is water.
- To prevent burns caused by excessive water temperature, if you add hot water to the machine, please do not add water exceeding 54°C.
- Avoid water entering the control panel area, and it is strictly prohibited to immerse the product in water for cleaning or rinsing.
- It is strictly prohibited to use on an empty stomach, after a full meal, drunkenness and strenuous exercise.
- Any damaged components must be replaced by the manufacturer, its maintenance department or professionals from similar departments.
- Users must not dismantle or repair by themselves.
- It is prohibited to replace the power cord. You must use the power cord that comes with the product
- If the power cord is damaged, it must be replaced by the manufacturer, its maintenance department or a specialist from a similar department to avoid danger.
- Do not use it while standing on the foot bath.
- It is strictly prohibited to pour water from the control panel or wipe the control panel with a wet towe
- This product is for home use only, not for commercial use, or outdoor use.
- Do not use multiple household appliances on the same power outlet.
- This product is strictly prohibited from being used in environments with flammable and explosive materials.
Notice
-
When not in use, please unplug the power plug. When unplugging or plugging in the power plug,do not use wet hands.
-
Do not use the power cord to pull the product.
-
Please protect the power cord and place it properly before and after use.
-
It is strictly prohibited to store in water to prevent frostbite on parts when the temperature is too low.
-
Children, people with physical disabilities and people who are not sensitive to heat should use this product according to the product usage requirements under the supervision of a guardian.
-
If you are undergoing medical treatment or have other serious diseases, please use it with caution.
If you need to use it, please follow the doctor’s advice and must be accompanied by a dedicated person. -
Only the same can be used.
-
Please fill and pour water from the end away from the control panel.
-
When the machine is working, do not let children play in or near the machine.
-
Please turn off all functions before unplugging the power plug and put the product in standby mode.
-
If liquid leaks from the appliance, the appliance must no longer be used.
Warn
- Do not use the appliance if it shows signs of damage.
- It is strictly forbidden to put your hands or feet between the casing and the base when the product is folded.
- Not suitable for use by pregnant women and children. If women want to use this product during menstruation, please follow your doctor’s advice.
- Before pouring water into the product, please check whether the drain cover is closed to prevent water from flowing out.
- Product is not intended to be used to warm animals.
- When the product is subjected to water aging testing on the production line, a small amount of water may remain, but it can be used normally after cleaning.
- Please pay attention to protect the product to prevent collision damage.
- Prevent hair, lint and other dirt and debris from entering the appliance.
- Please clean the basin, filter cover and filter cotton after use.
- The product is not waterproof, please use the product in a dry and water-free environment.
- Keep the filter cover and filter cotton clean to avoid clogging and damaging the foot bath.
- The product nameplate is attached to the bottom of the product.
Product Description
Control Panel
-
Temperature Display Area: When the constant temperature function is turned on, the temperature display area displays the current water temperature. Touch the “heating/lowering” button, and the temperature display area switches to display the set temperature. When a fault occurs, the temperature display area will display the fault code.
-
Time Display Area: When the constant temperature function is turned on, the time display area displays the set time.
-
0n/Off Key: Short press the on/off key to turn on/off. (Warm reminder: When the product is turned on and unfolded, without any operation, the product will automatically shut down after 5 minutes and the device will not fold. When the product is turned on and folded, without any operation, 1 The product automatically shuts down after minutes.)
-
Long Press to Lift: After the product is turned on, touch and hold the “lift” button for 3 seconds to turn on the lift function. During the lifting process, tap the “long press to lift” button to pause the lift.
Touch and hold it again for 3 seconds to restart the lift function. (Warm reminder: It is strictly prohibited to turn on the lifting function when the product is unfolded and there is water in the basin.
When the battery power is low, the red battery icon lights up, and the lifting function cannot be turned on at this time. Please charge and then turn on the lifting function.) -
Long Press the Constant Temperature: Touch and hold the “long press constant temperature” button for 3 seconds to turn on the function in the wired power-on state. If the current water temperature is lower than the set temperature, the heater starts to heat the water, and the set time does not count down at this time. When the water temperature reaches the set temperature, the heater starts to keep the water warm, and the set time starts counting down. When the function is on, tap the “long press” button to turn off the function. (Warm reminder: It is strictly forbidden to turn on the constant temperature function when there is no water in the basin.)
-
Automatic Massage: Touch the “Auto Massage” button to turn on the function when the device is powered on. When the function is on, touch the “Auto Massage” button to turn it off.
(Warm reminder: If the constant temperature and automatic massage functions are turned on at the same time, when the countdown of the constant temperature function ends, the automatic massage function will be turned off simultaneously. If the automatic massage function is turned on separately,it will automatically turn off after 30 minutes by default.) -
Heating/Cooling: The “warming/cooling” button can only be operated after the constant temperature function is turned on. Touch the “warming/cooling” button lightly, and the temperature display area will display the set temperature. Each time you touch it, the set temperature will be displayed. The temperature increases or decreases by 1°C, long press can change continuously, and the temperature can be adjusted in 35~48°C cycle. After resetting the temperature, the heater will heat at this set temperature the next time the constant temperature function is turned on.
-
Adding Time/Subtracting Time: The “adding time/subtracting time” button can only be operated after the constant temperature function is turned on. Each time you touch the “adding time/subtracting time” button, the set time will increase or decrease by 5 minutes. Press and hold for continuous changes. , 5-60 minute cycle adjustable. After resetting the time, the machine will perform the countdown function at this set time the next time the constant temperature function is turned on.
-
icon description
Instructions for use
Turn on the product and unfold the product: Take out the folded product, place it on a flat surface, short press the power button in the wireless state to turn it on, then enter the wireless power on state, long press the “lift” button for 3 seconds to turn on the opening and lowering function, the product Unfold slowly.
- Short press the power button to turn on
- Press and hold the “lift” button for 3 seconds to turn on the lift function
- Expansion completed
Tips: When the battery is low, the red battery icon lights up, and the
lifting function cannot be enabled.
Please connect the power cable to charge the battery and then enable the
lifting function.)
Open the upper cover: After the product is unfolded, hold the clasp of the front section of the upper cover with your hands, flip up the entire upper cover, then fold the thermal insulation front cover downwards, and put the folded upper cover down as a whole. Complete Open the lid.
- Turn the entire upper cover upwards
- Fold the thermal insulation front cover down
- Put down the folded upper cover
Add water to the basin: Before adding water to the basin, please make sure that the drainage cover at the front of the product is closed. Pour an appropriate amount of water into the foot bath after opening the cover. The water level should not be higher than the highest water level.
- Check if the drain cover is closed
- Pour an appropriate amount of water into the basin. The water level should not be higher than the highest water level.
Power on:
Take out the leakage protection power cord, put the long side of the plug
end up and the short side down, and then push the plug end against the left
bulge of the socket slide cover, and push the socket slide cover to the right.
When the socket slide cover slides to the right, insert the power cord tail
into the field to the end of the rain cotton from the wine line field into the
220V south center at this time, the field indicator is hit away Gary field
instructs the rainbow to put please press the reset button on the plug. After
the power is turned on, the product enters the wired startup state.
- Place the plug tail against the bulge on the left side of the socket slide cover, and push the socket slide cover to the right. When the socket slide cover slides to the right, insert the plug tail inward to the end.
- Insert the leakage protection plug into the socket, and the plug indicator light will light up. If the plug indicator light does not light up, please press the reset button.
Start to use:
After the water temperature is heated to the set temperature, the feet can
be put into the basin for use, and the automatic massage function can be
turned on according to the actual needs. The foot bath time is 20-30 minutes,
and the warm water can be properly drunk during the foot bath
Mobile products:
After use, unplug the power cord (at this time, you can not shut down),and
the product enters the wireless startup state. Pull out the retractable handle
at the back of the product, and drag the product to a place where it is
convenient to drain water (as shown below).
Drainage:
Drag the product to the place that is convenient for drainage, press the
drainage button on the base, and the drainage cover will automatically open
and start draining. After draining the water, press the drainage cover back to
the original position by hand and make sure that it is pressed to the end.
Product folding:
Long touch the “long press lift” button for 3 seconds to open and drop the
function, and the product folds slowly.
Shutdown storage: after the folding is completed, press the switch key to shut down, and then store the folded product in a ventilated and dry place.
APP Usage Instructions
Connect to MIJIA APP
This product has been connected to Mijia, can be controlled by MIJIA APP or
Xiaoai students. Scan the QR code, download and install Mijia APP, users who
have installed Mijia APP will directly enter the device connection page. Or
search for “MIJIA” in the APP store to download and install the Mijia app.
Open the home page of Mijia APP, click “+” in the upper right corner of the
page,and add devices according to the APP prompts. (Tips: Due to the upgrade
and update of Mijia APP, the actual operation may be slightly different from
the above description, please follow the instructions in the current Mijia
APP. Connection to MIJIA APP is only supported under 2.4GWi-Fi.)
Wi-Fi connection
The Wi-Fi icon flashes when you turn on the device for the first time, search
for the device through the MIJIA APP, and you can connect. The Wi-Fi icon
lights up after the connection and turns off when the device is powered off.
(Tip: Wi-Fi connection is recommended when the cable is turned on.)
Reset the Wi-Fi
To reset Wi-Fi, hold down the “Long Lift” button and the “Long Thermostat”
button for 7 seconds at the same time.
After the reset is successful, the Wi-Fi icon flashes and the foot bath enters
the waiting state. (Tips: If you can’t find the product, please reset the Wi-
Fi.)
Cleaning and Maintenance
- When cleaning or storing, please unplug the power plug.
- When the foot bath has been used for a period of time, please clean the filter cover and filter cotton in time. Please refer to the following steps for specific steps.
Disassemble and clean the filter cover: Rotate the filter cover counterclockwise, lift the filter cover upwards, take out the filter cotton in the filter cover and clean the filter cover and filter cotton.
Install the filter cover: Align the notch at the bottom of the filter cover with the water inlet protrusion, put down the filter cover, and tighten the filter cover clockwise.
- After each use of this machine, please clean it before storing it. When cleaning the footbath,use a damp cloth to clean the unit.
- Do not use harsh or abrasive detergents. After cleaning, dry the product with a dry cloth before storing it.
- When the product is not in use, please store it in a ventilated and dry place indoors.
Basic Parameter
Precautions for battery use
- Do not repair, disassemble or modify this product yourself.
- Do not collide, squeeze, drop, throw or scratch this product.
- Which takes about ours to timy charged to turn on the power to charge the battery,which takes about 3 hours to fully charge.
- If the humidity of the machine is too high, deformation, expansion, and battery leakage occur during storage, stop using the machine immediately and contact the after-sales service center.
Remove battery
A Warning: After removing the battery, the product will be scrapped.
The following operations are for reference only when the product is discarded.
Do not disassemble it for daily use and maintenance.
- Disconnect the external power supply and remove the product cover.
- Remove the battery lead terminal from the mainboard. Sokal
- Remove the battery and wrap the terminal with an insulating gel.
- Waste batteries should be placed in a fixed recycling point and disposed of in accordance with local environmental laws and guidelines.
Attention:
- The battery must be removed from the appliance before it is discarded.
- Power off the appliance before removing the battery.
- Non-professionals do not disassemble!
Troubleshooting
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>