BABY LOCK BLG-SCF Side Cutter Foot

Baby Lock Sewing Accessories – Side Cutter Foot

Product Information

The Side Cutter Foot (BLG-SCF) is a sewing accessory designed to simulate a serged stitch on a sewing machine. It allows you to easily sew an overcasting stitch to lock and align the thread over the fabric edge. The foot also features a built-in knife blade for trimming raw edges.

Usage Instructions

1. Remove the presser foot from your sewing machine.
2. Select a stitch from stitches 1-25 to 1-29, which are designated for use with the Side Cutter Foot.
3. Make sure the fork of the side cutter’s operating lever is firmly set onto the needle clamp screw.
4. Position the side cutter so that the side cutter pin is aligned with the notch in the presser foot holder.
5. Lower the presser foot.
6. Cut a fabric section of approximately 20 mm (approx. 3/4 inch) using the built-in knife blade.
7. Position the fabric so that the right side of the cut is on top of the guide plate and the left side of the cut is underneath the presser foot.
8. Thread the needle manually and pull out a long section of the upper thread. Pass it below the presser foot and pull it out in the fabric feed direction.
9. Start sewing.

Note:

• If the width has been adjusted, turn the handwheel by hand to check that the needle does not touch the side cutter. If the needle touches the side cutter, it might cause the needle to break.
• When sewing straight stitches while using the Side Cutter Foot, the seam margin should be approximately 5 mm (approx. 3/16 inch).
• If the fabric is not positioned correctly, the fabric will not be cut. Ensure the fabric is set as explained in the previous section before starting to sew.

For further assistance or inquiries, please contact Baby Lock customer support at 800-422-2952">800-422-2952 or visit their website at www.babylock.com.

Baby Lock Sewing Accessories

Side Cutter Foot
(BLG-SCF)

Instructions

To simulate a serged stitch on a sewing machine, nothing comes closer than the side cutter foot. Easily sew an overcasting stitch to lock and perfectly align the thread over the fabric edge. This convenient foot even trims raw edges with the built-in knife blade.

INSTRUCTIONS:

1. Stitches 1-25 to 1-29 are designated for use with the Side Cutter Foot.

2. Select a stitch.

3. Remove the presser foot.

4. Position the fork on the side cutter’s operating lever onto the needle clamp screw.

5. Needle clamp screw

6. Operating lever
   Note: Make sure the fork of the operating lever is set onto the needle clamp, screw firmly.

7. Position the side cutter so the side cutter pin is aligned with the notch in the presser foot holder, and then lower the presser foot.

8. Notch in presser foot holder

9. Pin

  * The side cutter is attached.

6. Make a cut of approximately 20 mm (approx. 3/4 inch) in the fabric.

   • 20 mm (approx. 3/4 inch)

7. Position the fabric so the right side of the cut is on top of the guide plate and the left side of the cut is underneath the presser foot.

8. Guide plate (lower knife)

9. Presser foot
   Note: If the fabric is not positioned correctly, the fabric will not be cut.

10. Thread the needle manually and pull out a long section of the upper thread. Pass it below the presser foot and pull it out in the fabric feed direction.

11. Presser foot

12. Upper thread

13. Start sewing.
    A seam allowance is cut while the stitching is sewn.
    Note: If the width has been adjusted, turn the handwheel by hand to check that the needle does not touch the side cutter. If the needle touches the side cutter, it might cause the needle to break.

When Sewing Straight Stitches While Using the Side Cutter The seam margin should be approximately 5 mm (approx. 3/16 inch).

1. Seam margin

Tips: The fabric will not be cut if the whole fabric is simply spread out underneath the presser foot guide plate. Set the fabric as explained in the previous section, and then start sewing.

• One layer of 13 oz. denim can be cut.
• Clean the side cutter after use to avoid having dust and scraps of thread build up on it.
• Add a small amount of oil as required to the cutting edge of the cutter.

800-422-2952

www.babylock.com

References

• Baby Lock - Baby Lock Sewing Machines | For the Love of Sewing

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>