OPCOM OFG005 GrowTank Tall Plant Hydroponics Installation Guide

: June 5, 2024
: OPCOM

Table of Contents

OPCOM OFG005 GrowTank Tall Plant Hydroponics
Assembly
Seedling
Optional Accessories
Maintenance
Troubleshooting
Q&A
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

OPCOM OFG005 GrowTank Tall Plant Hydroponics

Thank you for purchasing OPCOM GrowTank, the indoor hydroponics growing system. It is designed for easy use and efficient growing system by one-touch AUTO mode. It holds up to 8 plants capacity. Please read the quick guide carefully before setting it up. For details video, please visit the Official Website: http://www.opcomfarm.com.

Assembly

A1. Remove all parts from the box and check all accessories. OPCOM-OFG005
-GrowTank-Tall-Plant-Hydroponics-fig-1

Grow Kit

Accessory A2.Assemble GrowTanK

Assembly

Place four Hanging rings on each corner of the water tank.
Insert 4 aluminum Frame tubes (1) and secure their position.
Extend the upper 4 aluminum Frame tubes (2) by aligning and twisting the treads on the poles of step 2.
Use H tube(1) and Frame tube(4) to assemble L 1 square frame with extended poles of step 3 together and screw closely.
Connect another upper 4 plastic Frame tube(3), then assemble L2 Frame with 2 H tube(2) and 1 Frame tube(5), and assemble it on the top of the plastic tubes, screw closely.
Tighten the metal Hanging _Ring with L200B and the long plastic Frame tube(5). Hien ensure metal nng chain go through the metal nng in the LED light and set the height by bucl<ling two metal nng together.
After adjusting the height of LED, wind the lifting rope around.
Electric line setup
Connect control box to the front tube of the square frame.
Connect L200B LED lighe quick release adapter to the cable on the control box. L200B can adjust 2 ki_nas of grow light, R:B(S:1 )/R:8(9:1 ), to meet different planting stage requirement.
Water line setup
Place the pump to the slot base and fixed.
Other Installation
Add 21 gallons/ 80L(80% full) water to water tank.

Chart I: Control Box Mode

OPCOM-OFG005-GrowTank-Tall-Plant-Hydroponics-fig-5

Most plants can be grown using the AUTO mode.
The remote controller supports wireless remote control.
When Power On, press the hold POWER button until 2 beep sound (About 5 seconds) to reset power on the timeline.
When Power Off, press the hold POWER button until 2 beep sound (About 5 seconds) to reset the power off the timeline.

Seedling

Germination Stage

Open the Rockwool sponge package, wet the sponge(Fig 1)
Open the pod stick package put it into each planting basket(Fig2)
PUt into the seedling tray. (Fig3) Spray water and keep the sponge wet every day.
Place the seedling tray with cover in the shade or cover it with black cloth.

Chart II: Plant Stage

Please keep the Pod stick package in the refrigerator if you don’t use it. Recommended temperature is 41°F-50°F.
LED light moder1: R:8=9:1 is suitable for the plant leaf growth stage,moder2: R:8=9:1 is suitable for the plant blossom and fruit stage.

B2.Young Plant Stage

Add 21 gallons of water to the water tank(Fig4).
Add adjustment into the water tank and ensure EC value between(+ 1.0mS/cm)(Fig4) A spoon=1g / B spoon=5g / C spoon=10g
Ensure ph between 5.5-6.S(adjust by pH+/-). For EC&pH adjustment instructions, please refer
During the young plant stage (around 2 inches), turn on the LED and Pump. Please refer to the Chartwell.
You can choose different light hanging methods/positions for various plants base on you needs.(FigS)
Change or adjust water every 1-2 weeks according to above item 3&4. Some flowers/ fruit plants may need higher EC(over 2.0) at flower/ fruit stage. Please refer to plants information before you choose and plant.

BJ.Growing Stage

Set up the climbing net around the 4 tubes in the grow tank.
Choose 4 plants and move them to suitable holes for better growing.
Cover the empty plating sites to keep the rock wool wet and stop moss from growing up and
Stable them by using a climbing net or clip them on the poles.
Growtank can accommodate up to 8 plants and you can use ropes to go through the 4 metal rings on the water tank and fix them on the celling to allow the plants to climb(Fig6).
When young plants grow to 3-4 inches in height, switch the control box to growing mode. Please refer to Chart II.
After 4-6 weeks, harvest the larger plants for consumption and keep smaller plants growing.
To save time, sow the new seeds in a sprout tray one week before you restart the planting process.

B4.Blossom Stage

After about 6 weeks, add NT-adjuster to raise EC value to 2-2.5 for the flower stage of the plants.
Ensure pH value between 5.5-and 6.5 (adjust by pH+/-). For EC and pH instructions, please refer to Chart II.

BS.Fruit Stage

Note to add NT- Adjuster and water to raise EC value to 2.5-3 for fruit stage of the plants.
if necessary set an Anti-insect net to prevent insects attack.

Optional Accessories

Maintenance

E1.Add Water
Measure the pH/EC value every 1-2 weeks and add water to achieve the value balance.

E2.Change Water

After a cycle of planting, you may want to change water or clean the unit (fig 1)
When changing water, clean water gateway on each planting layers, you may also add moss detergent in the water tank to avoid the moss remaining.
On a regular basis of every 1-2 weeks, clean the filtering sponge in the pump.

E3.EC meter Use and Calibration

keep the electrode of EC meter clean and cover the eletrode protective cap when not in use.
Remove batteries when the EC/pH meter is not used for a long period of time.

Troubleshooting

Lamps not Iighting up

| Make sure all power cables are connected.
---|---
Make sure Power button is ON.

Make sure LED status is ON.

Pump has a buzzing sound| Pump may make a buzzing sound in the beginning due to air inside the pump. After a minute with water running through the pump, this sould be reduced.
The lamp/ pump stop after hours| Control Box is designed with Auto, HI and LOW modes, which turn the lamps and the pump on

Installation steps of water pump