Streamline SF-TR50L-000 STREAMFLO Portable Trolley System Instruction Manual
- June 5, 2024
- Streamline
Table of Contents
INSTRUCTION
MANUAL
STREAMFLO®
Codes:
SF-TR50L-000
SF-TR50L-072 INSTR-SF-TR50L-072
The warranty on all Machines and Equipment is for 1 year (12-months) from the
RECORDED DATE OF PURCHASE.
THIS WARRANTY EXCLUDES NORMAL MAINTENANCE ITEMS, including but not limited to
HOSES, FILTERS, O-RINGS, DIAPHRAGMS, VALVES, GASKETS, CARBON BRUSHES and
damage to motors and other components as a result of failure to replace normal
maintenance items. THIS LIST IS NOT EXHAUSTIVE.
If STREAMLINE® receives notice of such defects during the warranty period,
STREAMLINE® will either, at its opinion, repair or replace components that
prove to be defective.
Replacement parts will only be supplied under warranty, upon the inspection
and approval of the defective parts by STREAMLINE®.
Should it be necessary to supply replacement parts before the opportunity to
inspect, these will be charged at current prices and a credit will only be
issued upon subsequent inspection and warranty approval by STREAMLINE®.
The customer is responsible for the cost of the return of the defective part.
If the warranty is approved, STREAMLINE® will pay for the cost of the repaired
or replacement part.
This warranty excludes the following conditions and circumstances which are at
the discretion of STREAMLINE®:
Wear and tear, misuse, abuse improper maintenance, frost damage, the use of
chemicals other than those supplied or approved by STREAMLINE®, improper
installation or repair, unauthorized modification, incidental or consequential
costs, loss or damage, service, labor or third party charges, the cost of
returning defective parts to STREAMLINE®.
This warranty constitutes the exclusive remedy of any purchaser of a
STREAMLINE® unit and is in lieu of all other warranties, express or implied,
including without limitation any implied warranty of merchantability or
fitness for use, to the fullest extent permitted by law. In no event shall any
implied warranty of merchantability or fitness for use exceed the term of the
applicable warranty stated above and STREAMLINE® shall have no other
obligation or liability.
Important
Unfortunately, these rights cannot be transferred to a third party.
Why STREAMLINE®?
Flexibility
- STREAMLINE® systems can be built according to customers’ exact requirements
- For non-standard systems, the user’s needs or specifications are listened to and turned into reality.
Quality
- Whilst price is important, quality is remembered long after price is forgotten
- We insist on sourcing brand name products from around the world, only of a reputable quality, and bring them together under the STREAMLINE® name
- All STREAMLINE® products carry a full one year’s warranty, according to the manufacturers’ standard terms and conditions of sale.
Service
- We have an in-house technical helpline able to answer most of your questions relating to the capabilities and functionalities of all STREAMLINE® products
- If we get it wrong, we will put it right. If you are sent a wrong item, we will immediately attend to sending you the correct item and arrange a collection of the wrong item without any quibbles
- STREAMLINE® is backed by a comprehensive range of massive stocks providing you with a ‘one-stop-shop for all your requirements.
Thank you for purchasing a STREAMLINE® Water Filtration System
Your trolley has been assembled and tested to ensure that there are no leaks
and to ensure that the pump and pressure switches are functioning correctly.
Enclosed is a TDS Meter that measures parts per million in water. This enables
you to test water quality periodically to ensure that your system is producing
pure water, i.e. 0ppm, so as to achieve the best cleaning results. We would
recommend that a sample is taken from water that is being pumped to the brush
head on the water-fed pole.
When cleaning windows, remember to pay special attention to the frames,
especially if it is the first time this method of window cleaning is being
used. The most important part of the cleaning process is the rinsing after the
window has been cleaned. To do this, lift the brush away from the glass and
move the head from side to side working from top to bottom, allowing water to
create a sheet, therefore rinsing the glass.
Extra care must be taken if the water refuses to ‘sheet’, as this makes
rinsing more difficult. If you are cleaning windows on a warm day, the rinsing
procedure must be done meticulously, as warm direct sunlight can cause
spotting due to insufficient rinsing.
Charging the battery
-
To charge the battery, use the battery charger supplied with the trolley.
-
Charge the battery for approx. 5 hours.
-
Remove an electrical connection from battery (See figure 1).
-
Slide the battery out of the battery holder (See figure 2) Plug the charger into the mains supply; Red light should be lit on the charger.
-
Connect the charger to the battery using the charger socket on the side of the battery.
Do not attempt under any circumstances to charge the battery from the Red/Black output points on the battery. This is an output point, as damage will be caused to both the battery and the charger -
Power light (Red) lit and depending on the charge in battery some Green lights may also be lit. During charge, the remaining Green lights will blink until they also become solid.
-
Solid Green lights mean the battery is fully charged.
-
Remove the battery from the charger and switch it off at mains.
-
The battery is ready to use.
-
The battery must be charged fortnightly, even if the trolley is not being used. Failure to do this may cause the battery voltage to drop and minimize its charging capacity.
Setting Up
- Remove the container lids and riser tube and fill the container with pre-filtered water. If the trolley is fitted with a resin filter, fill the container with tap water, Re-insert the riser tube and screw the lids on securely.
- Insert the pole hose connection into the outlet fitting on the trolley and lie the pole on the ground with the brush jet nozzles facing up.
- Switch the pump on by pressing and holding the up button on the STREAMLINE® flow controller, until the display illuminates.
- Set the pump speed to 30 by pressing the up or down buttons.
- Allow the pump to prime until water flows out of the brush nozzle jets.
- Adjust the flow by using arrows, according to the cleaning operation on hand.
- When complete, switch the pump off by pressing and holding the button.
Maintenance
Filter Servicing (If fitted with this option)
Regular meter readings should be taken using the enclosed TDS meter to ensure
that the system is producing pure water. When the water TDS no longer
registers 000ppm, follow the servicing sequence below.
Changing the Resin
Make sure that the pump is switched off and that the system is depressurized
by pressing the red button. Unscrew the bowl of the DI filter, situated on the
back of the trolley, using the filter spanner which is provided. Remove the
spent DI resin cartridge and replace it with a cartridge filled with new DI
resin. Refit the filter bowl and tighten it adequately using the spanner.
(Remember to ensure the rubber seal is in place before tightening.)
The resin within the cartridge can be refilled by unscrewing the cap, tipping
out the spent resin, and refilling it with new resin. Used resin should be
disposed of in a responsible manner. If in doubt please refer to your local
waste collection service provider.
Transportation
Remove the container lid and riser tube. Remove the water container. Loosen
the two locking nuts on either side of the handle and lift and fold the handle
forwards to enable the trolley to fit into a confined space.
Care should be taken so as to avoid pinching the fingers when folding the
handle.
Notes
Hamilton House, 8 Fairfax Road,
Heathfield Industrial Estate,
Newton Abbot
Devon, TQ12 6UD
United Kingdom
Telephone: +44 (0) 1626 830 830
Email: sales@streamline.systems
Visit www.streamline.systems
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>