Powerwerks PWR12 High Power Active Speakers Owner’s Manual

June 5, 2024
Powerwerks

Powerwerks-PWR12-High-Power-Active-Speakers-LOGO

Powerwerks PWR12 High Power Active Speakers

Powerwerks-PWR12-High-Power-Active-Speakers-PRODUCT

IMPORTANT SAFETY INSTRUCTIONS – ENGLISH

Danger
Exposure to extremely high noise levels may cause permanent hearing loss. Individuals vary considerably to noise-induced hearing loss but nearly everyone will lose some hearing if exposed to sufficiently intense noise for a sufficient time. The U.S. Government’s Occupational Safety and Health Administration (OSHA) has specified the following permissible noise level exposures:

According to OSHA, any exposure in the above permissible limits could result in some hearing loss. Earplugs or protectors in the ear canal or over the ears must be worn when operating this amplification system in order to prevent a permanent hearing loss. If exposure in excess of the limits as put forth above, to ensure against potentially harmful exposure to high sound pressure levels, it is recommended that all persons exposed to equipment capable of inducing high sound pressure levels, such as this amplification system, be protected by hearing protectors while this unit is in operation.

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE THE CHASSIS. NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

THIS SYMBOL IS INTENDED TO ALERT THE USER TO THE PRESENCE OF NON-INSULATED “DANGEROUS VOLTAGE” WITHIN THE PRODUCT’S ENCLOSURE THAT MAY BE OF SUFFICIENT MAGNITUDE TO CONSTITUTE A RISK OF ELECTRIC SHOCK TO PERSONS.
THIS SYMBOL IS INTENDED TO ALERT THE USER TO THE PRESENCE OF IMPORTANT OPERATING AND MAINTENANCE
(SERVICING) INSTRUCTIONS IN THE LITERATURE ACCOMPANYING THE UNIT.
APPARATUS SHALL NOT BE EXPOSED TO DRIPPING OR SPLASHING AND NO OBJECTS FILLED WITH LIQUIDS, SUCH AS VASES, SHALL BE PLACED ON THE APPARATUS.

  1. Read all safety and operating instructions before using this product

  2. All safety and operating instructions should be kept for future reference.

  3. Read and understand all warnings listed on the operating instructions.

  4. Follow all operating instructions to operate this product.

  5. This product should not be used near water, i.e. Bathtub, sink, swimming pool, wet basement, etc.

  6. Only use dry cloth to clean this product.

  7. Do not block any ventilation openings, It should not be placed flat against a wall or placed in a built-in enclosure that will impede the flow of cooling air.

  8. Do not install this product near any heat sources; such as, radiators, heat registers, stoves or other apparatus (including heat-producing amplifiers) that produce heat.

  9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades one wider than the other. A grounding-type plug has two blades and a third grounding prong. The wide blade or the third prong is provided for your safety if the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.

  10. Protect the power cord being walked on or pinched, particularly at plugs, convenience receptacles, and the point where they exit from the (I apparatus. Do not break the
    ground pin of the power supply cord.

  11. Only use attachments specified by the manufacturer.

  12. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.

  13. Unplug this apparatus during lightning storms or when unused for long periods of time.

  14. Care should be taken so that objects do not fall and liquids are not spilled into the unit through the ventilation ports or any other openings.

  15. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way; such as, the power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally or has been dropped.

  16. WARNING: To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture.

  17. When the MAINS plug or an appliance coupler is used as the disconnect device, the disconnect device shall remain readily operable.

  18. Protective Ground Terminal: The apparatus shall be connected to an AC main socket with a protective earth ground connection.

CAUTION

This device complies with Part 15 of the FCC Rules / Industry Canada licence- exempt RSS standard(s ). Operation is subject to the following two conditions:

  1. this device may not cause harmful interference, and
  2. this device must accept any interference received, including interference that may cause undesired operation.

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
This equipment has been tested and found to comply with the limits for an Oasis B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and receiver.
  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/Vf technician for help.

Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interfer­ence to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power ( ever.p.) is not more than that necessary for successful communication.
MPE Reminding
To satisfy FCC I IC RF exposure requirements, a separation distance of 20 cm or more should be maintained between the antenna of this device and persons during device operation. To ensure compliance, operations at closer to this distance is not recommended.

CONTROLS & FEATURES

Powerwerks-PWR12-High-Power-Active-Speakers-FIG4Powerwerks-PWR12-High-Power-Active-Speakers-
FIG5

FEATURES

  1. Bluetooth® pairing button
  2. Link button
  3. Input 1 channel gain control knob
  4. Input 1 channel mic/line input toggle button
  5. Input 2 channel gain control knob
  6. Input 2 channel mic/line input toggle button
  7. Input 1 channel input combo socket
  8. Input 2 channel input combo socket
  9. LineOut
  10. Master volume: click to enter the EQ preset mode (Main/Monitor/Dj/Speech) GI Limit LED indicator
  11. Power LED indicator
  12. FUSE IEC mains inlet
  13. Main power switch ( on/off)

INSTRUCTIONS

  1. Prior to switching on, turn the volume down to a minimum.
  2. Connect the audio source to the appropriate input socket.
  3. Connect to the mains supply.
  4. Switch on the audio source, followed by the active speaker.
  5. Set the volume with the applicable control.
  6. Adjust the bass + treble.

BLUETOOTH® PAIRING INSTRUCTIONS

  1. Press and hold the PAIR button until the light flashes quickly.
  2. Pairing connections can now be made via Bluetooth® on devices such as smartphones and tablets.
  3. To temporarily bypass the Bluetooth® connection press the PAIR button once until the light flashes slowly. Press again once to reconnect.
  4. To exit/disable Bluetooth® press and hold the PAIR button until the light turns off.

SAFETY REMINDER

  • Intended for Indoor or protected from weather use only.
  • Do not place near open flame.
  • Make sure the unit is stable. Place on a flat surface or an appropriate speaker stand with a wide footprint able to hold 25 lbs. or greater.
  • Do not place liquids on top of the unit or subject to high humidity.
  • No user-serviceable parts inside. Always refer to a qualified repair service when service is required.
  • Mind the system Clip Indicator. Keeping the volume to a level that keeps the Clip Indicator only blinking when a large amount of bass is present will deliver a better listening experience and prolong the life of the unit.

TECHNICAL SPECIFICATIONS

PWR12 DETAILS

Power 1050 watts peak/ 350 watts RMS
Speakers 12″ Low-frequency driver
Horn 34mm High-frequency compression driver
Frequency Response 45Hz-20KHz
Presets 4 mode DSP EQ Presets
Bluetooth ® Yes
Linking capability Bluetooth® TRUE STEREO
Cabinet Single plywood enclosure

PWR10 DETAILS

Power 600 Watts Peak/ 200 watts RMS
Speakers 1O” Low-frequency driver
Horn 34mm High-frequency compression driver
Frequency Response 55Hz-20Hz
Presets 4 mode DSP EQ Presets
Bluetooth ® Yes
Linking capability Bluetooth® TRUE STEREO
Cabinet Single plywood enclosure

POWERED SPEAKERS WITH BLUETOOTH®
The Powerwerks PWR series speakers are high-performance active speakers featuring loads of class D power. The PWR12 features 1,050 watts of power through one 12″ low-frequency driver and one high-frequency compression driver. The PWR10 features 600 watts of power through one 10″ low-frequency driver and one high-frequency compression driver.
Each features four modes of onboard DSP EQ presets and up to three channels of audio input including Bluetooth® audio streaming. The XLR thru allows performers to enhance their sound by connecting to other powered speakers for system expansion. You can also connect with another Powerwerks PWR series speaker (Bluetooth® only) for even more expandability. The portable design & standard speaker pole mount make for an easy setup and breakdown.
The Powerwerks PWR series high-power speakers will satisfy all your performance needs.Powerwerks-PWR12-High-Power-Active-Speakers-
FIG6 Powerwerks-PWR12-High-Power-Active-Speakers-
FIG7

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals