artika DIM-PULW Pulsar Smart Wi-Fi Dimmer Instruction Manual
- June 5, 2024
- artika
Table of Contents
Smart Wi-Fi dimmer – Pulsar TM
INSTRUCTION MANUAL
IMPORTANT, KEEP FOR FUTURE REFERENCE:
PLEASE READ CAREFULLY.
FCC ID: 2AUHG-DIM-PULW-1
IC : 21811-DIMPULW
Rev. 14.05.2021
Made in China
Residential use only
Indoor use only
INSTRUCTION MANUAL
INCLUDED
| Item | Description | Quantity |
|---|---|---|
| Wire connector | x 4 +1 extra | |
| Junction box screw | x 2 +1 extra | |
| Switch assembled | x 1 | |
| Switch plate | x 1 |
WHAT YOU WILL NEED…
IMPORTANT
The installer and/or user must read, understand and follow these instructions
before installing the product. This product must be properly installed before
it is used.
If instructions are not followed, the manufacturer will not be held
responsible for any problems or product malfunction. Failure to follow
installation and/or operating instructions voids the warranty. We recommend
that this product be installed by a certified electrician. In some states or
provinces, it is a legal requirement for this type
of product to be installed by a certified electrician, according to the
electrical and building codes effective in the region where the unit is used.
WARNING:
Risk of electrical shock.
Turn off breaker at the panel.
SWITCH OFF THE MAIN
ELECTRICAL SUPPLY FROM THE
FUSE BOX/CIRCUIT BREAKER
BEFORE INSTALLING THE UNIT OR DOING ANY MAINTENANCE.
DIMMER FUNCTIONS
-
Turn ON the dimmer Hold 5s to pair
-
Turn OFF the dimmer
-
Brightness UP signal
-
Brightness level display area
-
ON-OFF / WI-FI signal
ON position (Red light)
OFF position (No light)
Default pairing mode (Blue flash rapidly)
AP mode (1 blue flash / 3 sec)
Ø internet (Blue flash slowly) -
Brightness DOWN signal
CONNECTION
Single pole switches only. (fig. A)
Not compatible with
a 3-way switch. (fig. B) 
RECOMMENDED
BULBS
INCANDESCENT BULB
Total power
500 Watts maximum
LED BULB
Total power
150 Watts maximum
STEP-BY-STEP
INSTALLATION
- Turn off the power from the electrical panel and the circuit breaker. Make sure the power is off before removing the old plug.
- Remove the switch plate by unscrewing the screws on the switch plate. (fig. 1)
- Unscrew the screws of the switch. Remove the old switch. (fig. 2)
STEP-BY-STEP
INSTALLATION
4. Identify the wires before disconnecting them from the old switch. Identify
the white wire (N), the black wire (L), the grounding wire (G) and the red
wire (Lo).
RED (Lo): load
BLACK (L): Live
WHITE (N): Neutral
NON-INSULATED (G): Ground
5. Disconnect the old switch (fig. 3).
STEP-BY-STEP
INSTALLATION
6. Use wire connectors to connect the switch wires to your home wires,
following the diagram. Be careful to match “LINE” and “LOAD” wires. (fig. 4)
RED (Lo): load
BLACK (L): Live
WHITE (N): Neutral
NON-INSULATED (G): Ground
Use wire connectors home wires, following the dia“LINE” and “LOAD” wi
7. Remove your identification stickers.
STEP-BY-STEP
INSTALLATION
6. Screw the switch to the junction box . (fig. 5)
STEP-BY-STEP
INSTALLATION
7. Fix the plate to the swith. (fig. 6)
8. Restore electrical power.
CONVENTIONAL USE
This device can be used as a regular unit without using the APP. However, some
of the functions are only possible to control with the APP.
Ex: programming based on different parameters.
SMART CONNECTION
-
Download the Artika app
Download the Artika app from your
App Store (IOS users) / Google Play (Android users). -
Login / Register
Follow the step by step instructions given in the app. (fig. 1)
3. Device Pairing
A) To add a device, click on the “+” at the top right corner. (fig. 2)
B) Select the pairing method “Add manually” or “Auto Scan”. (fig. 3)
If you decide to add manually, please select your device in the list
NOTE: Devices are separated by category, please select the right one on
the left end side of the screen.
C) Follow the instructions shown in the app.
3. Device Pairing
A) Press and hold the “ON” button for 5 seconds, green light will flash and
will become steady upon successful pairing.
B) To add a device, click on the “+” at the top right corner. (fig. 2)
C) Select the pairing method “Add manually” or “Auto Scan”. (fig. 3)
If you decide to add manually, please select your device in the list
NOTE: Devices are separated by category, please select the right one on
the left end side of the screen.
D) Follow the instructions shown in the app. 
CAUTION
If manual pairing method has been selected, make sure that the mode of
connection selected is EZ Mode. This should be selected as default, but if the
AP mode is selected, the pairing will fail. To change the connection method,
click on “AP mode” at the top right corner and select EZ mode from the
dropdown list. (fig. 4) ****
Canada (IC)
Operation is subject to the following two conditions:
- This device may not cause interference, and
- this device must accept any interference, including interference that may cause undesired operation of the device.
USA (FCC)
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions:
1. This device may not cause harmful interference; and
2. this device must accept any interference received, including interference
that may cause undesired operation.
NOTE: This equipment has been tested and found to comply with the limits
for Class B digital device, pursuant to part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference in
a residential installation. This equipment generates, uses and can radiate
radio frequency energy and if not
installed and used in accordance with the instructions, may cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on. The user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and the receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
NOTE2: Any changes or modifications to this unit not expressly approved
by the party responsible for compliance could void the user’s authority to
operate the equipment. This equipment complies with the FCC RF radiation
exposure limits set forth for an uncontrolled environment. This equipment
should be installed
and operated with a minimum distance of 20cm between the radiator and any part
of your body.
WARRANTY
Artika For Living Inc. is proud to offer you a three (3) years limited
warranty on manufacturing defects from the date of purchase for residential
use only. The warranty is extended to the original owner in USA and Canada and
is non-transferable. It does not apply to retailers, commercial applications
or establishments. The original sales receipt
is required for all warranty claims. The remedy under this limited warranty
shall be a product or part replacement at Artika’s discretion as provided
herein and cannot exceed the original purchase price. This warranty is valid
only on products installed in accordance with the building code and laws
effective in the region where the unit is used as well as in
accordance with the provided instruction manual. It does not cover products
installed incorrectly or subjected to abnormal use. Product(s) or component
part(s) may be required to be returned for inspection and verification. Normal
wear and tear, misuse, negligence, vandalism, improper maintenance (surface
damage due to chemical interaction or cleaning agents including, but not
limited to, scouring pads, use of cleaners containing abrasives, alcohol or
other organic solvents) improper handling, accident, abuse, fire, flood,
theft, acts of God, neglect, or alteration of the product will not be covered
under this limited warranty. It excludes any accessories that accompany the
product including but not limited to bulbs or batteries. The warranty does not
cover handling, labor, transportation, or any other cost associated with the
installation or replacement of the product. This limited warranty is valid in
the country of purchase and by Artika authorized retailers only. Artika for
Living Inc. will not be held responsible for any direct or consequential
damages or injuries related to the use of this product arising from improper
use or installation of this product. Please visit www.artika.com to discover
more about Artika for Living Inc.
Artika For Living Inc.
50th Avenue,
Montréal (Lachine), Québec
Canada H8T 2V5
1-866-661-9606
support@artika.com
www.artika.com
Customer Service
Monday to Friday
9 a.m. – 5 p.m. EST
Documents / Resources
|
artika DIM-PULW Pulsar Smart Wi-Fi
Dimmer
[pdf] Instruction Manual
DIM-PULW-1, DIMPULW1, 2AUHG-DIM-PULW-1, 2AUHGDIMPULW1, DIM-PULW Pulsar Smart
Wi-Fi Dimmer, Pulsar Smart Wi-Fi Dimmer
---|---
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>