ring Smart Lighting Bridge App User Guide
- June 5, 2024
- Ring
Table of Contents
ring Smart Lighting Bridge App
Quick Start
- Set up and install your Ring Bridge.
- Open the Ring app. Then, tap Set Up a Device and follow the in-app instructions.
- Scan this code. This identifies your Ring Mailbox Sensor for fast and easy setup.
IMPORTANT PRODUCT INFORMATION
Safety and Compliance Information Use Responsibly. Read all instructions and safety information before use.
SAFETY INFORMATION
FAILURE TO FOLLOW THESE SAFETY INSTRUCTIONS COULD RESULT IN FIRE, ELECTRIC
SHOCK, OR OTHER INJURY OR DAMAGE.
BATTERY SAFETY
This product contains alkaline batteries. This device requires batteries for
use. Only use new 1.5V alkaline or 1.2 NiMH rechargeable AAA-sized batteries.
Never mix old and new batteries. Keep all of the batteries out of the reach of
children. Do not open, disassemble, puncture, cut, bend, shred or heat the
batteries and do not allow metal objects to touch the battery terminals on the
remote as they can become hot and cause burns. Remove all batteries if they
are worn out or before storing your Device for an extended period of time.
Dispose of all batteries in accordance with applicable laws and regulations
and do not dispose of batteries by throwing them into a fire. If any batteries
begin to leak, take steps to prevent the fluid from coming into direct contact
with skin or clothes as the fluid could be corrosive and may be toxic. Remove
the batteries and clean the battery compartment in accordance with the battery
manufacturer’s recommendations.
PRODUCT SPECIFICATIONS
Model Number: Ring Mailbox Sensor Electrical Rating: 3 x AAA-cell batteries
Temperature Rating: -4°F to 122°F (-20°C to 50°C)
RECYCLING YOUR DEVICE PROPERLY
In some areas, the disposal of certain electronic devices is regulated. Make
sure you dispose of, or recycle, your device in accordance with
your local laws and regulations. FCC Compliance: This device complies with
part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this
device must accept any interference received, including interference that may
cause undesired operation. The party responsible for FCC compliance is: Ring
LLC, 1523 26th St, Santa Monica, CA USA, 90404 By purchasing or using the
product, you agree to the Terms of Service found at ring.com/terms.
For information on our warranty, theft protection,
and Ring Protect Plans, see ring.com/legal.
IMPORTANT PRODUCT INFORMATION
FOR UNITES STATES CUSTOMERS
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Information on this device is on file with the FCC and can be found by inputting the device’s FCC ID into the FCC ID Search form available at https://www.fcc.gov/oet/ea/fccid. The output power of the radio technology used in the Products is below the radio frequency exposure limits set by the FCC. Nevertheless, it is advised to use the product in such a manner that minimizes the potential for human contact during normal operation. This device should be installed and operated with at least 20 cm between the radiator and your body. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help. Caution: Any changes or modifications to this device not explicitly approved by manufacturer could void your authority to operate this equipment.
FOR CANADIAN CUSTOMERS
Innovation, Science and Economic Development Canada (ISED) Compliance. This
device contains licence-exempt transmitter(s)/receiver(s) that comply with
Innovation, Science and Economic Development Canada’s licence- exempt RSS(s).
Operation is subject to the following two conditions: (1) This device may not
cause interference. (2) This device must accept any interference, including
interference that may cause undesired operation of the device. Caution: Any
changes or modifications to this device not explicitly approved by
manufacturer could void your authority to operate this equipment.
Information Regarding Exposure to Radio Frequency Energy
This equipment complies with IC RSS-102 RF exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
a minimum distance of 20 cm between the radiator and your body.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>