POWER FIST 8978652 Pivoting High Velocity Blower Fan User Manual
- June 5, 2024
- POWER FIST
Table of Contents
POWER FIST 8978652 Pivoting High-Velocity Blower Fan
SPECIFICATIONS
| Airflow (CFM) | 1,365 |
|---|---|
| Voltage Rating (V AC) | 120 |
| Current Rating (A) | 0.9 |
| Wattage Rating (W) | 108 |
| Frequency Rating (Hz) | 60 |
| Motor Type | Open |
| Bearing Type | Ball |
| Number of Speeds | 3 |
| Cord Length (ft) | 6 |
| Fan Blade Material | Plastic |
| Fan Speed (RPM) | 1,624 |
| Decibel Rating (dB) | 60 |
| Housing Material | Plastic |
| Control Type | Manual Control |
| Indoor/Outdoor | Indoor |
SAFETY
WARNING! Read and understand all instructions before using this tool. The operator must follow basic precautions to reduce the risk of personal injury and/or damage to the equipment. Keep this manual for safety warnings, precautions, operating or inspection, and maintenance instructions.
HAZARD DEFINITIONS
Please familiarize yourself with the hazard notices found in this manual. A notice
Pivoting High-Velocity Blower Fan
is an alert that there is a possibility of property damage, injury, or death
if certain instructions are not followed.
DANGER! This notice indicates an immediate and specific hazard that will
result in severe personal injury or death if the proper precautions are not
taken. WARNING! This notice indicates a specific hazard or unsafe practice
that could result in severe personal injury or death if the proper precautions
are not taken.
SPECIFIC SAFETY PRECAUTIONS
WARNING!
- DO NOT let comfort or familiarity with the product (gained from repeated use) replace strict adherence to the tool safety rules. If you use this tool unsafely or incorrectly, you can suffer serious personal injury.
- This fan is for residential use only. It is not intended to be used in industrial or agricultural settings.
- Do not use this fan to ventilate areas where flammable liquids or vapors are used, stored or are present, including paints, gasoline, varnishes, floor refinishing products or solvents.
- Unplug the fan before moving it or performing maintenance. Do not touch the fan when your hands are wet.
- Those who are not qualified electricians should not disassemble, repair or rebuild the fan. If the supply cord is damaged, it has to be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid hazards.
- The power cord is equipped with a three-prong grounded plug that must be inserted into a matching receptacle. Under no circumstances should the grounding prong be cut off the plug.
- To reduce the risk of fire or electric shock, do not use this fan with any solid-state speed control device.
- Do not use the fan with an extension cord.
- Do not run cord under carpeting. Do not cover the cord with throw rugs, runners, or similar coverings. Do not route cord under furniture or appliances. Arrange cord away from traffic area and where it will not be tripped over.
- Always place the fan on a stable, flat, level surface while in operation to prevent the fan from overturning.
OPERATION
WARNING! Always be sure the plug fits tightly into the outlet.
- Place the fan on a safe, flat surface where it cannot fall or be pulled by the cord.
- Select desired direction of airflow by pivoting the fan drum body forward or backward.
- Select preferred speed (1-Low, 2- Med, 3-High) by rotating the switch on the side of the fan.
- To turn the fan OFF, turn the switch to OFF (0) and unplug the fan from the electrical outlet.
BREAKER RESET
A 10-amp breaker is provided as a safety feature of this fan. When you use an appliance that has more amperage than allowed, the breaker will trip. To reset, unplug the appliance causing the breaker to trip, and press the RESET BUTTON marked as the figure show.
CARE & MAINTENANCE
- Maintain the tool with care. A tool in good condition is efficient, easier to control, and will have fewer problems.
- Inspect the tool components periodically. Repair or replace damaged or worn components. Only use identical replacement parts when servicing.
- Maintain the tool’s labels and nameplates. These carry important information.
If unreadable or missing, contact Princess Auto Ltd. for replacements.
WARNING! Only qualified service personnel should repair the tool. An improperly repaired tool may present a hazard to the user and/or others.
CLEANING
- Unplug the fan before cleaning. Don’t use any water for cleaning surfaces.
- Slightly moisten a cloth and then wipe off the surfaces of the fan.
- Never use alcohol or solvents such as gasoline, benzene, paint thinner, or other harsh cleaners.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>