VIDICON BINGO Plus PIR Sensor User Manual

VIDICON BINGO Plus PIR Sensor

Product Information

is
connected.
High RFI protection| Thanks to the total lack of traditional amplifiers, the
detector has a very high RFI immunity.
Pet immunity| All our detectors are pet immune up to 15 Kg, thanks to the new
lens design combined with the digital analysis system.

Product Usage Instructions

1. Installation Procedure:
   • Ensure not to cover, partially or completely, the field of vision of the detector.
   • Note that the pet immune function is not certified IMQ.
   • Refer to Fig 2 for screw placement.
2. Adjustments and Connection:
   • Dip 1 – off = 1 pulse, on = 2 pulse
   • Dip 2 – off = 7mt, on = 15mt range
   • Dip 3 – off = led off, on = led on
   • Jumpers T – A – EOL open = all contact free without resistors
   • Jumpers T – A – EOL closed = double balancing (alarm2k2 – tamper 4K7) ALARM terminal alarm when the jumpers closed
   • Internal EOL – jumper closed
   • External EOL – jumper opened
   • Refer to the user manual for more detailed adjustment and connection instructions.

INTRODUCTION

BINGO Plus detectors represent the best choice for residential and industrial installations in the security sector.
It use only digital PIRs, thus avoiding the conversion that generally must be done in traditional detectors, where the analog PIR is
amplified and converted to digital. Thanks to the TOTALLY digital technology, the detector is much more accurate in detecting intrusions and not suffering of alterations such as: white light, ultraviolet light, temperature, air movement due to heating/cooling systems and it is totally immune to radiated and conducted electromagnetic disturbances. Bingo Plus detectors are equipped with lenses made by Fresnel Technologies, Inc.
LODIFF® technology for optics realization in combination with POLY IR® materials make it a product with highest quality and efficiency.

• White light protection
  The detector is digitally ltered from white light.

• High RFI protection
  Thanks to the total lack of traditional ampliers, the detector has a very high RFI immunity.

• Ultraviolet stabilization POLY IR®4 material for lenses
  The lens is molded in POLY IR® materials. These materials offer the  best combination of transmittance, environmental stability, and color of any polymer. Materials available for the 8-14micron region of the infrared.

• Full digital PIR
  The detector has no analog components, the full digital PIR is connected

• Pet immunity
  All our detectors are pet immune up to 15
  Kg, thanks to the new lens design combined with the digital analysis system.

• LODIFF™ Fresnel Lens Technology
  The lens array is made by tiling piecesof LODIFF* lenses. These lenses offer significantly improved performance over typical constant-groove-width Fresnel.

INSTALLATION PROCEDURE

• By using a thin screwdriver, loosen the screw on the bottom and open the housing (see figure 1)
• Remove the PCB from the base by levering on the ABS supports (see figure 2)
• Pierce the knock on the base of cover on the desired point for fixing (or use the optional swivel bracket not certified INQ)
• Pierce the kconck on the base and fix a screw between wall and cover for back tamper protection (see fig2)
• recommended height from 1.8mt to 2.2mt
• slide the cable into the back seat, and out of the top hole
• Wire up the terminals following the connections shown in figure.
• NOTE: do not cover, partially or completely, the field of vision of the detector
• NOTE: the pet immune function is not certified IMQ

ADJUSTMENTS AND CONNECTION

• Dip 1– > off =1 pulse – on = 2 pulse
• Dip 2 – > off = 7mt – on =15mt range
• Dip 3 – > off = led off – on = led on
• Jumpers T – A – EOL open = all contact Free without resistors
• Jumpers T – A – EOL closed = double balancing (alarm2k2 – tamper 4K7)
• ALARM te L terminal alarm when the jumpers closed)
• SUPPLY: p .8Vcc @ 11 mA / 19 mA MAX

Meets the requirements: EN 50131-2-2 Grade 2 EN 50131-2-2 Cl II
Cumple los requisitos: EN 50131-2-2 Grado 2 EN 50131-2-2 ClaInstallation must be carried out following the local installation norms by qualified personnel. The manufacturer refuses any responsibility when changes or unauthorized repairs are made to the product/system.It is recommended to test the operation of the alarm product/system at least once a month. Despite frequent testing and due to, but not limited to, any or all of the following: tampering, electrical or communication disruption or improper use, it is possible for the product/system to fail to prevent burglary, rubbery, fire or otherwise. A properly installed and maintained alarm system can only reduce the risk that this happens.
www.vidicon.pl

References

• Vidicon - Systemy Alarmowe, Telewizja PrzemysÅ‚owa, Klimatyzacja

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>