HEGEL H120 Music System User Manual
- June 5, 2024
- HEGEL
Table of Contents
H120 User Manual
Congratulations on your new Hegel H120.
All Hegel products are based on a simple philosophy: Add as little as
possible. We always aim to keep the music signal close to the original
recording. We are constantly looking for ways to lower distortion and noise.
By lowering noise, we unveil layers of music covered by noise. And by lowering
the distortion we can have a better and more precise reproduction of the
recording. We work hard to give you the best possible music experience. Our
minimalistic Scandinavian design is styled to fit in with any interior. The
products are easy to operate and manufactured according to the best quality
principles.
Bent Holter
Founder Hegel Music System
What’s In The Box
Quick Start
-
Connect your speakers
For the best audio experience, the distance between the listener and each speaker should be the same.
-
Connect a source
-
Connect the power cord
-
Turn on the amplifier
General Use
Operating the H120
The source and volume can be changed using the input and volume selector on
the front panel or using the remote control.
Power Button
The H120 amplifier can be switched on and off with the power button located on
the underside of the amplifier, towards the front of the unit.
NOTE: When powering up, the H120 takes a few seconds to calibrate, the
outputs are muted and the volume flashes to indicate that mute is on. This is
normal and is part of the start-up procedure.
NOTE: When the H120 has been switched off, wait 30 seconds before
powering it on again.
Headphone Output
Connect the 6.3mm headphone jack to the front of the H120. This activates the
headphone volume control and mutes the speaker outputs.
NOTE: Variable Line Output is still active.
Sleep/Auto standby
In compliance with the EU Energy Efficiency Directive the Hegel device will
automatically switch off after 15 minutes without sensing a signal, or with
very low signal on the speaker out puts. You can disable or change the Sleep/
Auto Standbysettings in the device’s menu.
Connections
Always power the amplifier off before connecting
input/output audio cables and the power cable.
Speakers
- Right outputs
- Left outputs
Line Outputs
-
Variable Line Level (RCA)
Analog Inputs -
Balanced (XLR): Standard balanced analog input (Pin 1 is Chassis Ground; Pin 2 is Positive Phase; Pin 3 is Negative Phase)
-
Analog 1(RCA): Standard analog input
-
Analog 2(RCA): Standard analog input
If you want to connect the amplifier to a Home Theater system, see Device Menu.
AC Power Connection
- AC Power connector with fuse holder: 230V/115V/100V AC depending on country.
Digital Connections
- Coax1: Input Coaxial/RCA
- Optical1: Input TOSLINK/EIAJ Optical
- Optical2: Input TOSLINK/EIAJ Optical
- Optical3: Input TOSLINK/EIAJ Optical
- Computer USB input
- Home network connection (LAN – RJ45)
Remote Control – RC8
Remote control buttons (starting top left)
- PREV Skip to previous track on most media players
- PLAY Play/Pause on most media players
- NEXT Skip to next track on most media players
- DAC+ Input source selector button for Hegel DACs
- ECO On/Off (standby)
- DISP Display on/off (hold for off)
- PREV Skip to the previous track on Hegel CD-players
- PLAY Play/Pause for Hegel CD-players
- NEXT skip to the next track on Hegel CD-players
- IN+ Switches to next input on Hegel amplifiers
- STOP Stop/Eject for Hegel CD-players
- VOL+ Volume up for Hegel amplifiers
- IN- Switches to previous input on Hegel amplifiers
- MUTE Mute for Hegel amplifiers
- VOL- Volume down for Hegel amplifiers
General information
The Hegel amplifier can be controlled with the included Hegel RC8 Remote
Control. The RC8 controls Hegel products, such as amplifiers and
preamplifiers, and most media
players, avoiding the need for multiple remote controls The remote control
uses two standard 1.5volt LR03 AAA batteries. To insert the batteries, use a
crosshead (Phillips) screwdriver to gently remove the four screws on the
underside of the remote control.
Insert the batteries with the correct polarity with + sign and – sign, as
shown inside the battery holder. Be careful when inserting the batteries to
not damage the battery holder.
Replace the cover. Insert the screws by gently turning them by hand, to avoid
damaging the threads in the remote control chassis. Do not tighten the screws
too much, as this can damage the screws and the soft metal chassis of the
remote control.
CAUTION: Do not drop the remote control on the floor, as this can damage
its internal parts and the battery holder.
Mute
The MUTE(14) button mutes the outputs on the amplifier. The volume flashes to
indicate that mute is on. Press the mute button, or adjust the volume level,
to switch mute off.
On/Off (standby)
The ECO(5) button will turn the amplifier on or off (standby).
Display On/Off
The DISP(6) button may be used to turn the display on or off. Hold the DISP
button for more than 1 second to turn the display off. When adjusting inputs
or volume the
display will light up momentarily. To turn the display on again, press DISP.
Set startup volume
A user-defined volume may be used as the power-up volume. Adjust the volume to
the desired start-up level. Press DAC+(4) and VOL-(15) simultaneously. The
volume number will blink three times to indicate that the new start-up volume
has been saved.
Set max volume
A user-defined volume may be used as the max volume. Adjust the volume to the
desired maximum level. Press DAC+(4) and VOL+(12) simultaneously. The volume
indicator will blink three times to indicate that the new max volume has been
saved. To restore to the default max volume of 99, turn the volume all the way
up and press DAC+ and VOL+ once more. The volume indicator will blink 99 three
times to indicate that the max volume has been reset.
Reset to Factory Default Settings
By pressing and holding the DAC+(4) button while pressing MUTE(14), the
amplifier will be reset to factory settings. This will clear all user-defined
settings, including IP settings, and restart the amplifier. This can also be
done in the amplifier’s menu. Software updates will not be affected.
Network Setup
Connection
To be able to use the amplifier’s network and streaming features, the
amplifier needs to be connected to your local network. Connect your Hegel
amplifier using an Ethernet cable (not supplied) from the network connection
(LAN – RJ45) port on the back of the amplifier to your router.
Network settings
The amplifier has its own Network Configuration page where you can change the
amplifier’s network name and IP settings. To open the page, enter your
amplifier’s IP address in a browser window. You can find the IP address in
the amplifier’smenu under “Network”.
For detailed information on the Network Configuration page, supported formats
and much more, please visit support.hegel.com
NOTE: Some of the features of the Hegel device require an internet
connection.
Wake up on Network
Even when the amplifier is in standby mode the network connection is active.
The amplifier can be woken up from standby by starting playback to the Hegel.
Status Indicators
The Hegel device will display the network status in the lower-left corner of
the display.
Network status is OK:|
---|---
Network status is not OK:
Troubleshooting
If you experience problems with connecting the amplifier to the network or
have other network issues, please try the following:
Disconnect the power chord for at least 30 seconds and then reconnect.
If that does not help, try the following:
Enter the amplifier menu and select factory reset.
Streaming
AirPlay
When using AirPlay, you can send the music stream from an AirPlay-compatible
device to the Hegel device. All AirPlay-compatible devices will detect the
Hegel device in their
list of AirPlay speakers.
When both devices are connected to the same network, the AirPlay icon will be
displayed, and you can select the Hegel device as an AirPlay speaker. You are
now ready to send the music stream to your amplifier.
Spotify Connect
When using Spotify Connect, you can send the music stream from Spotify to the
Hegel device.
Use your phone, tablet or computer as a remote control for Spotify.
Go to spotify.com/connect to learn how.
UPnP/DLNA
The amplifier can function as a Digital Media Renderer. This means that it can
receive and play media files from a UPnP/ DLNA compatible media player. When
using UPnP/DLNA streaming, you can send the music stream from locally stored
files or music streaming services to the Hegel device. UPnP stands for
Universal Plug and Play and is a widely used media streaming protocol. That
means it is supported by a host of products and applications. For details on
how to set up your media player, please refer to the user manual supplied with
the player.
WARNING: When streaming to the Hegel device, always remember to check the player/device volume setting before pressing play. The Hegel device will change its volume to the volume set in the player.
Device Menu
Navigation
To enter the device menu, turn the amplifier on and press and hold the PLAY(2)
button for 5 seconds. To navigate the menu, use the PREV(1) and NEXT(3)
buttons. To select
a sub-menu or feature, press the “PLAY(2) button. To exit the menu, navigate
to “Exit” and press PLAY(2), or turn one of the amplifier’s knobs.
NOTE: Some menu features require a connection to the internet to work
properly. See Network Setup
Info
Information about the Hardware Version of your product and the Software
Version currently running.
Network
Information about the Network Device Name and the IP Address of your product.
Update
Check for and download the newest software for your product.
Sleep
By default, the amplifier will automatically switch itself off after 15
minutes without music, or with a very low signal on the speaker outputs. Sleep
/ Auto-off can be disabled in this menu.
Reset
Here you can reset the product to the de-fault factory settings. This will not
affect any software updates you have installed.
HT
Most inputs can be configured to act as a Home Theater input. This will set
the input volume at a fixed high volume level.
NOTE: The Hegel device menu can be updated with new features and options.
For an up to date and in-depth description of the menu and its features,
please visit support.hegel.com
https://support.hegel.com/product-articles/device-menu
Miscellaneous
Using the USB Connection
When you connect your Hegel device to a computer with a USB cable (not
included), the Hegel will automatically install itself as a USB soundcard on
all newer versions of Windows, macOS, and most Linux operating systems.
NOTE: The first time you connect your computer to your Hegel device,
connect the computer to the internet and close all media players.
Troubleshooting with macOS
The Hegel device is connected, but there is no sound: Go to System
Preferences – Sound – Output and select “TE7022 Audiow/ SPDIF” as the Output
Device.
Connecting a subwoofer
The most common way to connect a subwoofer is from the variable line output on
your Hegel amplifier. If your subwoofer is equipped with “high level” speaker
wire terminals you can also use this. Many subwoofer manufacturers recommend
this type of connection if it is available.
Please consult your subwoofer manual for detailed instructions on how to
connect and configure your subwoofer for the best audio result.
Power
All electrical components should be turned off or in standby when not in use.
This due to safety, because all electrical components can fail, and it is good
for the environment. Leaving your product on all the time could also shorten
the life expectancy of the product.
That being said, our products sound even better when they are warmed up,
typically after about 15 minutes of listening at a moderate volume.
Connecting your TV
The best way to connect your TV is by using one of the optical inputs. If
there is no sound, try changing the sound output in the TV’s settings menu.
The setting should be changed to PCM or stereo. Please consult your TV’s
manual for detailed instructions.
General Information
Technical Specifications
H120 Integrated Amplifier
| Power output | 2*75W in 8 Ohms |
|---|---|
| Minimum load | 2 Ohms |
| Analog Inputs | 1*Balanced (XLR), |
2Unbalanced (RCA),
Digital Inputs| 1Coaxial S/PDIF,
3Optical S/PDIF,
1USB, 1Network
Line level Output| 1Unbalanced Variable(RCA)
Frequency response| 5Hz-100kHz
Signal-to-noise ratio| More than 100dB
Crosstalk| Less than -100dB
Distortion| Less than 0.01% @
50W 8 Ohms 1kHz
Intermodulation| Less than 0.01%
(19kHz + 20kHz)
Damping factor| More than 2000
(main power output stage)
Dimensions| 8cm x 43cm x 31cm
(HxWxD)
12kg shipment weight.
3.15” x 16.93” x 12.20”
(HxWxD) 26.46lbs shipment weight.
Transport and Shipment
When packing the amplifier, please follow these instructions to avoid damaging
the unit: Be careful not to hold the volume- and source knobs when lifting the
amplifier. ,
Insert the amplifier into the plastic bag.
Ensure the plastic bag does not press tightly on the knobs as this may damage
them during transportation.
Place the amplifier into the shock absorbers. Place the amplifier with
absorbers into the original cardboard box. xD)
Use and Placement
The Hegel amplifier should be placed on a flat, hard surface for proper
cooling. The amplifier must never be placed on a carpet or similar surface as
this obstructs air circulation
through the unit. For the same reason, the amplifier should have sufficient
clearing above, and never be covered while in use.
The amplifier will automatically switch itself off if overheated. When it
cools down the amplifier turns back on and the volume is set to 0.
Cleaning
Fingerprints or stains on the front panel or top cover can be removed with a
cloth moistened with warm water or a mild detergent suitable for cleaning
mirrors and windows.
Warning
Hegel products should only be opened or serviced by certified technicians. The
devices contain electronic components that may cause severe electric shock.
Work performed on Hegel products by unqualified personnel may cause serious
damage or personal injury.
Opening of the product by non-authorized personnel will void the warranty.
The products must not be exposed to rain or moisture.
Warranty
All Hegel products come with a 2-year warranty against defective materials and
workmanship. The warranty is limited to the region where it was originally
purchased.
There is no need for registering the warranty. The purchase receipt will work
as a start date for the warranty.
In case you need assistance with your Hegel product, please contact your
nearest dealer or distributor. These are listed on
www.hegel.com. Our dealers are carefully chosen for
their expertise and should be able to help you with any Hegel-related issue.
You can of course always reach us directly by sending an email to
info@hegel.com or by contacting us on our social
media pages.
Disclaimers
The Spotify Software is subject to third party licenses found here:
www.spotify.com/connect/third-party-licenses
AirPlay works with iPhone, iPad, and iPod touch, or Mac and PC with iTunes.
Use of the “Works with Apple AirPlay” badge means that an accessory has been
designed to work specifically with the technology identified in the badge and
has been certified by the developer to meet Apple performance standards. Apple
AirPlay, iPad, iPhone, iPod touch, Mac and macOS are trademarks of Apple Inc.,
registered in the U.S. and other countries. The trademark “iPhone” is used in
Japan with a license from Aiphone K.K.
For more information about the H120,
please visit www.hegel.com
References
- Spotify - Connect
- Select Your Product
- Hegel Music Systems - High-end audio electronics designed in Norway
- Third Party Licenses | Spotify for Developers
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>