GEMMY Orchestra of Lights Hub with Smart Speaker Instructions
- June 5, 2024
- GEMMY
Table of Contents
Orchestra of Lights Hub with Smart Speaker
Instructions Manual
Congratulations! You are now the proud owner of a LED light show. Please
read the directions carefully before use.
SAFETY WARNING: Remove all plastic fasteners and tags. These are part of
the packaging and should be discarded.
SAVE THESE INSTRUCTIONS – This manual contains important safety and
operating instructions for power units.
WARNING
ELECTRIC PRODUCT. Keep away from children. Not recommended for children under
3 years of age. As with all electrical products, precautions should be
observed during handling and use to reduce the risk of electric shock. If the
supply cord is damaged, it must be replaced by the manufacturer, its service
agent, or similarly qualified persons in order to avoid a hazard.
WARNING
Strobe lights have been known to trigger seizures in people with
photosensitive epilepsy.
IMPORTANT SAFETY INSTRUCTIONS
WHEN USING ELECTRICAL PRODUCTS, BASIC PRECAUTIONS
SHOULD ALWAYS BE FOLLOWED INCLUDING THE FOLLOWING:
READ AND FOLLOW ALL SAFETY INSTRUCTIONS
- Do not use seasonal products outdoors unless marked suitable for indoor and outdoor use. When products are used in outdoor applications, connect the product to a Ground Fault Circuit Interrupting (GFCI) outlet. If one is not provided, contact a qualified electrician for proper installation.
- This seasonal use product is not intended for permanent installation or use.
- Do not mount or place near gas or electric heaters, fireplace, candles, or other similar sources of heat.
- Do not secure the wiring of the product with staples or nails, or place it on sharp hooks or nails.
- Do not let lamps rest on the supply cord or on any wire.
- Unplug the product when leaving the house, when retiring for the night, or if left unattended.
- This is an electric product-not a toy To avoid the risk of fire, burns, personal injury, and electric shock it should be played with or placed where small children can reach it.
- Do not use this product for other than its intended use.
- Do not hang ornaments or other objects from the cord, wire, or light string.
- Do not close doors or windows on the product or extension cords as this may damage the wire insulation.
- Do not cover the product with cloth, paper, or any material not part of the product when in
- This product employs overload protection (fuse). A blown fuse indicates an overload or short-circuits situation. If the fuse blows, unplug the product from the Also unplug any additional strings or products that may be attached to the product. Replace the fuse as per the user servicing instructions(follow product marking for proper fuse rating)and check the product. If the replacement fuse blows, a short-circuit may be present and the product should be discarded.
- Read and follow all instructions that are on the product or provided with the product.
Always unplug this product before installing or replacing fuses.
CAUTION: To reduce the risk of fire and electric shock:
Do not mount or support wires in a manner that can cut or damage wire
insulation.
SAVE THESE INSTRUCTIONS.
USE AND CARE INSTRUCTIONS
- Before using or reusing, inspect the product carefully. Discard any products that have cut, damaged, or frayed wire insulation or cords, cracks in the lamp holders or enclosures, loose connections, or exposed copper wire.
- When storing the product, carefully remove the product from wherever it is placed, including trees, branches, or bushes, to avoid any undue strain or stress on the product conductors, connections, and wires.
- When not in use, store neatly in a cool, dry location protected from sunlight.
USER SERVICING INSTRUCTIONS
To replace the fuse:
- Grasp plug and remove from the receptacle or other outlet device. Do not unplug by pulling on the cord.
- Open fuse cover. Slide open fuse access cover on top of attachment plug towards blades.
- Remove fuse carefully. Turn the fuse holder over to remove the fuse.
- RISK OF FIRE. Replace fuse only with 3 Amp, 125Volt fuse (provided with the product.)
- Close fuse cover. Slide closed the fuse access cover on top of the attachment plug.
- RISK OF FIRE. Do not replace the attachment plug. Contains a safety device (fuse) that should not be removed. Discard the product if the attachment plug is damaged.
CAUTION
This string is rated 24Watts ( 0.2Amps ), do not overload. Connect other
Lighting Strings or decorative outfits end-to-end up to a maximum of 216 Watts
(1.8 Amps) total.
If connecting to a lighting string that does not have a wattage (W) rating
(found on the tag within 6 inches of the plug), Calculate The wattage (W) as
follows: Multiply the current (0.2A) which is on the flag type tag Within 6
inches of the plug, by 120.
For example, the string is rated 120V, 60Hz, 0.2Amps, 0.2×120=24 Watts.
Add the wattage of each light string together for a total of 216 Watts or
less. (Do not exceed 216 Watts) Total amount of wattage that can be connected
is 216W-24W=192W.
CAUTION
To reduce the risk of fire or electric shock, do not attempt to replace lamps
or modify the string.
FOR INDOOR AND OUTDOOR USE
PACKAGE CONTENTS
Topper | 3 pieces |
---|---|
Pole | 3 pieces |
Stake | 3 pieces |
Extra fuse, 3A,125V | 2 pieces |
PREPARATION
Before beginning assembly, remove all parts from the carton. Compare the parts list and diagram above. If any part is missing or damaged, do not attempt to assemble or use the roduct.
- Estimated assembly time: 10-15 minutes.
ASSEMBLY INSTRUCTIONS
- Set out all contents on a clear, flat surface.
- Begin assembly by securing the stake into the ground.
- Place the pole on top of the stake. (see illustration)
- Attach the topper to the pole. (see illustration)
- Repeat the process until complete.
- Plug the power cord into a standard wall socket.
NOTE: This item is not a toy and should be used for decorative purposes only.
WARNING
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
CAUTION: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the distance between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help with an important announcement
Important Note:
Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
a minimum distance of 20cm between the radiator and your body.
This transmitter must not be co-located or operating in conjunction with any
other antenna or transmitter.
THESE INSTRUCTIONS ARE FOR THESE ITEM NUMBERS
880108
QD ID:91274
FCC Caution.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference, and
- this device must accept any interference received, including interference that may cause undesired operation.
Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance 20cm between the radiator & your body.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>