AUTOJOE ATJ-CA100 Cordless Digital Inflator Instruction Manual

AUTOJOE ATJ-CA100 Cordless Digital Inflat

IMPORTANT!

Safety Instructions

WARNING! Read all safety warnings, instructions, illustrations and specifications
provided with this device.

General Safety
WARNING! When using the device, basic safety precautions should always be followed. Failure to follow all instructions listed below may result in electric shock, fire and/or serious injury.

• Work area – Keep your work area clean and well lit.
• Device condition – Keep the device dry, clean and free from oil and grease.
• Explosion hazard – Do not operate the device in explosive atmospheres, such as in the presence of flammable liquids, gases or dust.
• Bystanders – All bystanders, children and pets should be kept a safe distance away from the work area.
• Stay alert – Remain alert at all time, use common sense and do not operate the device when tired, or under the influence of drugs or alcohol.
• Dress properly – Do not wear loose clothing or jewelry. They can get caught in moving parts. Non-slip footwear are recommended when working outdoors.
• Do not overreach – Keep proper footing and balance at all times.
• Usage – Do not use this device for any use case exept for which it was intended.
• ON/OFF – Do not attempt use the device if it fails to turn on or off
• Storage – When idle, store out of the reach of children and do not allow persons unfamiliar with the device or these instructions to operate it.
• Accessories – Use the device and any accessories in accordance with these instructions, taking into account the working conditions and the work to be performed

Electrical and Battery Safety

WARNING! Do not expose the device to rain or wet conditions. Water entering the unit may damage the device and increase the risk of electric shock.
CAUTION! Recharge only with the charging cable specified by the manufacturer

• Do not abuse the cable – Never carry the device by the cable or yank the cable to disconnect it from the outlet. Keep the cable away from heat, oil, and sharp edges.
• Charging – Do not leave the device unattended when it is plugged into an electrical outlet. Turn off the device, and unplug it before leaving.

WARNING! Under abusive conditions, liquid may be ejected from the battery; avoid contact. If contact accidentally occurs, flush with water. If liquid contacts eyes, seek additional medical help. Liquid ejected from the battery may cause irritation or burns.
WARNING! Do not use the device if damaged or modified. A damaged or modified device may exhibit unpredictable behavior resulting in fire, explosion or risk of injury.
WARNING! Do not expose the device to fire or excessive temperatures. Exposure to fire or high temperatures may cause an explosion.
NOTE: Follow all charging instructions and do not charge the device outside the temperature range of 41°F – 105ºF (5°C – 40.5°C). Do not charge the battery outside in freezing weather; charge it at room temperature.
WARNING! Do not touch the inflator or its charging cords with wet hands.
CAUTION! To reduce the risk of burns, do not open, crush, heat above 122°F (50°C), or incinerate.

Safety Symbols
The following table depicts and describes safety symbols that may appear on this product. Read, understand, and follow all instructions on the machine before attempting to assemble and operate.

Know Your Cordless Digital Inflator
Read the owner’s manual and safety rules carefully before using your Cordless Digital Inflator. Compare the illustration below to the actual unit in order to familiarize yourself with the location of the various controls and attachments. Save this manual for future reference

1. LED light
2. Air outlet
3.  Barrel jack
4. USB-C port
5.  USB-A port
6. PSI volume buttons
7. Tapered nozzle
8. Short tapered nozzle
9. Sports ball needle
10. Presta valve adapter
11. Barrel plug
12. USB-C plug
13. Air hose
14. Air chuck
15. USB-A plug
16. 2V DC plug
17. Mode button
18. Power button
19. LED button
20. LCD display
21. Inflator
22. Storage bag

Technical Data

• Pump …………………………………………………… 40 W
• Battery Capacity …………………………….. 2000 mAh
• Input …………………………………..5V DC | 2A USB-C 12V DC plug
• Output ………………………..5V DC | 2A | 4Ah USB-A
• Inflation Pressure Max. *……………………….. 140 PSI
• Working Pressure …………………………………. 60 PSI
• Duty Cycleɫ …………………………………………..10 min
• Inflation Rate ………………………0.4 CFM (10 L/min)
• Net Weight ………………………………. 1.3 lbs (0.6 kg)

**Unpacking

**

Carton Contents

• Inflator
• Air hose
• Tapered nozzle
• Short tapered nozzle
• Sports ball needle
• Presta valve adapter
• Storage bag
• 12V DC plug
• USB-A to USB-C cable
• Manual and registration card

1. Carefully remove the inflator and check to see that all of the above items are supplied.
2. Inspect the product carefully to make sure no breakage or damage occurred during shipping. If you find damaged or missing parts, DO NOT return the unit to the store. Please call the Snow Joe® + Sun Joe® customer service center at 1-866-SNOW JOE (1-866-766-9563).

NOTE: Do not discard the shipping carton and packaging material until you are ready to use your new cordless digital inflator. The packaging is made of recyclable materials. Properly dispose of these materials in accordance with local regulations.

IMPORTANT! The equipment and packaging material are not toys. Do not let children play with plastic bags, foils, or small parts. These items can be swallowed and pose a suffocation risk!
Charging over USB

NOTE: This power station should be fully charged before use or storage. Check the battery level indicator for the remaining charge in the battery.
Using the included USB-A to USB-C cable, plug the smaller USB-C connector into the corresponding USB-C port of inflator. Then plug the other end of the cable (USB-A) into a USB port on your vehicle, or alternatively into a USB adapter (not included) for charging at an electrical outlet (Fig. 1).

NOTE: To maximize charging speed, use a USB adapter rated at 10W or higher.
NOTE: You may also use other USB ports such as those on computers, wall outlets and power banks to charge your inflator.

Power over 12V DC
NOTE: The 12V DC auto power cable only provides working power to the device and does not charge the internal battery. To charge the battery use the USB-A to USB-C cable instead.
Using the included 12V DC auto power cable, plug the barrel plug into the barrel jack of the inflator. Then plug the 12V DC plug into the 12V DC socket of your vehicle (Fig. 2).

Battery Level Indicator
The battery level indicator can be found on the LCD display, which will illuminate and indicate the charge level when the unit is being used, and when the unit is being charged.

• The three bars on the indicator correspond to low, medium and high.
• The three bars will cycle from left to right while charging.
• Once the battery is fully charged, the three bars will remain static at which point unplug the USB-A to USB-C cable from the inflator.
  NOTE: Timely recharging of the tool will help prolong its battery life.

WARNING! The chargers do not automatically turn off when the battery is fully charged. Please take care not to leave the inflator plugged in. Unplug the charging cables when charging is complete.
IMPORTANT! Never allow the tool to become fully discharged as this will degrade the battery life over time.
WARNING! Continued and excessive overuse of the ON/OFF button can permanently damage the lithium-ion battery.

• During the charging procedure, the inflator will feel slightly warm to the touch. This is normal.
• When no further use is planned for an extended period of time, disconnect the charging cable from the unit and the electrical outlet/12V DC socket.
• Do not use the device while charging.

Battery Charging Tips

• To obtain the longest possible battery life, we suggest the following:
• Store and charge your inflator in a cool area. Temperatures above or below normal room temperature will shorten battery life.
• Never store the inflator with the battery in a discharged condition. Recharge the unit immediately after it is discharged.
• All batteries gradually lose their charge. The higher the temperature is, the faster they lose their charge. If you store your inflator for long periods of time without using it, recharge the battery every 6 months. This will extend its battery life.

NOTE: The inflator has been shipped in a low charge condition and should be fully charged before use.

Operation

1. To turn on the inflator, long press the power button until the LCD display illuminates (Fig. 3).
   NOTE: The LCD display will automatically turn off when not in use for 150 seconds or more.

2. Press the mode button to cycle between 4 different modes: ball, bicycle, motorcycle and car (Fig. 4).

3. The + and – buttons allow you to manually adjust the inflation pressure. This determines the pressure at which the inflator will pump
   up to. Press either the + or – buttons to increase or decrease pressure by increments of 0.5 PSI, or long press to quickly cycle the psi value up or down (Fig 5).

4. Once the desired PSI has been set, short press the power button to initiate inflation (Fig. 3).
   NOTE : Should the pump fail to reach the desired pressure setting within 15 minutes, the pump will automatically shut off.

Inflating with the Air Hose

Schrader valves (cars, motorcycles and mountain bikes) can be attached directly to the air chuck without any additional attachments.

1. Screw the air hose clockwise into the air outlet of the inflator (Fig. 6).
2. Unscrew the valve cap from the valve stem (Schrader) of your tire (Fig. 7).
3. Place the air chuck onto the threaded valve stem (Schrader), then press down on the air chuck clamp to secure the chuck onto the valve (Fig. 8).
4. Set the appropriate PSI according to the label on the driver’s side door or the vehicle’s user manual. Then short press the power button to initiate inflation (Fig. 3).

Inflating with Adapters
The air hose can be used with the provided adapters to inflate a variety of items. To use the adapters lift up the air chuck clamp, insert your adapter of choice into the air chuck, then press down on the air chuck clamp to secure the adapter in place (Fig 9).

Presta Valve Adapter
Presta valves are commonly used on road bikes and some mountain bikes. To inflate a bicycle tire, you will need to use the Presta valve adapter

1. Loosen the Presta valve locking nut on your bike’s valve stem (Fig. 10).
2. Thread the female end of the Presta valve adapter onto valve stem of the bicycle tire.
3. Clamp the end of the air chuck down onto the Presta valve adapter by pressing the air chuck clamp down until it locks into place (Fig. 11).
4. Set the appropriate PSI according to the bicycle’s tire wall. Then short press the power button to initiate inflation (Fig. 3).
5. After inflation, remove the air chuck and tighten the locking nut (Fig. 10).

Sports Ball Needle
Inflate all kinds of sports balls with the Sports ball needle (Fig. 12).

Tapered Nozzles
Inflate small plastic or rubber inflatables such as pool rings, beach balls, air mattresses, travel pillows and more with either of the two provided tapered nozzles (Fig. 13).

USB Power Bank
The Cordless Digital Inflator may also be used as a portable battery bank for remote, on-the-go charging of smartphones, tablets, speakers and more. Devices may be charged through the USB-A port (Fig. 14). Charging will start automatically upon connection.

LED Light
The LED button (labelled ) controls the LED light on the top of the inflator (Fig. 15). Follow the table below to activate the three different modes.

Care and Maintenance

Use the included storage bag to protect the digital inflator when not in use.
WARNING! Store the inflator away from hot surfaces or under direct sunlight to reduce the risk of a short circuit.
CAUTION! Have your device serviced by a qualified repair person using only identical replacement parts.
WARNING! Do not allow brake fluids, gasoline, petroleum-based products, solvents, etc., come in contact with plastic parts. Chemicals can damage, weaken or destroy plastic, which could result in personal injury.

Disposal

Recycling the tool

• Do not dispose of electrical devices as unsorted municipal waste. Use separate collection facilities.
• Contact your local government agency for information regarding the collection systems available.
• If electrical devices are disposed of in landfills or dumps, hazardous substances can leak into the groundwater and get into the food chain, damaging your health and well-being.

Recycling + Disposal
The product comes in a package that protects it against damage during shipping. Keep the package until you are sure that all parts have been delivered and the product is functioning properly. Recycle the package afterward or keep it for long-term storage. WEEE symbol. Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist. Check with your local authority or local store for recycling regulations.

Service + Support

If your Auto Joe™ ATJ-CA100 Cordless Digital Inflator requires service or maintenance, please call Snow Joe® + Sun Joe® customer service at 1-866-SNOWJOE (1-866-766-9563) for assistance.

Model + Serial Numbers
When contacting the company or arranging service from an authorized dealer, you will need to provide the model and serial numbers, which can be found on the registration card. Copy these numbers into the space provided below.

SNOW JOE® + SUN JOE® CUSTOMER PROMISE
ABOVE ALL ELSE, Snow Joe, LLC (“Snow Joe”) is dedicated to you, our customer. We strive to make your experience as pleasant as possible. Unfortunately, there are times when a Snow Joe®, Sun Joe®, or Aqua Joe® product (“Product”) does not work or breaks under normal operating conditions. We think it’s important that you know what you can expect from us. That’s why we have a Limited Warranty (“Warranty”) for our Products.

OUR WARRANTY:

Snow Joe warrants new, genuine, powered and non-powered Products to be free from defects in material or workmanship when used for ordinary household use for a period of two years from the date of purchase by the original, end-user purchaser when purchased from Snow Joe or from one of Snow Joe’s authorized sellers with proof of purchase. Because Snow Joe is unable to control the quality of its Products sold by unauthorized sellers, unless otherwise prohibited by law, this Warranty does not cover Products purchased from unauthorized sellers. If your Product does not work or there’s an issue with a specific part that is covered by the terms of this Warranty, Snow Joe will elect to either (1) send you a free replacement part, (2) replace the Product with a new or comparable product at no charge, or (3) repair the Product. How cool is that!
This Warranty gives you specific legal rights, and you may also have other rights which vary from State to State.

PRODUCT REGISTRATION:
Snow Joe strongly encourages you to register your Product. You can register online at snowjoe.com/register, or by printing and mailing in a registration card available online from our website, or calling our Customer Service Department at 1-866-SNOW JOE (1-866-766-9563), or by emailing us at [email protected]. Failure to register your Product will not diminish your warranty rights. However, registering your Product will allow Snow Joe to better serve you with any of your customer service needs.

WHO CAN SEEK LIMITED WARRANTY COVERAGE:
This Warranty is extended by Snow Joe to the original purchaser and original owner of the Product.

WHAT IS NOT COVERED?
This Warranty does not apply if the Product has been used commercially or for non-household or rental applications. This warranty also does not apply if the Product was purchased from an unauthorized seller. This warranty also does not cover cosmetic changes that do not affect performance. Wearing parts like belts, augers, chains and tines are not covered under this Warranty, and can be purchased at snowjoe.com or by calling 1-866-SNOW JOE (1-866-766-9563).

References

• Snow Joe: America's #1 Leader In Cordless Equipment, Pressure Washers & Snow Throwers
• Register Your Product | Product Registration For Your Snow Joe®, Sun Joe®, Aqua Joe®
• Snow Joe: America's #1 Leader In Cordless Equipment, Pressure Washers & Snow Throwers

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>